drm/i915/tv: Fix TV mode

Commit 1fd4a5a36f9f ("drm/connector: Rename legacy TV property") failed
to update all the users of the struct drm_tv_connector_state mode field,
which resulted in a build failure in i915.

However, a subsequent commit in the same series reintroduced a mode
field in that structure, with a different semantic but the same type,
with the assumption that all previous users were updated.

Since that didn't happen, the i915 driver now compiles, but mixes
accesses to the legacy_mode field and the newer mode field, but with the
previous semantics.

This obviously doesn't work very well, so we need to update the accesses
that weren't in the legacy renaming commit.

Fixes: 1fd4a5a36f9f ("drm/connector: Rename legacy TV property")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220131251.453060-1-mripard@kernel.org

drm/i915: Disable hotplug detection handlers during driver init/shutdown

As described in the previous two patches an unexpected connector
detection can happen during the init/shutdown sequences. Prevent these
by returning the connector's current status from the detection handlers.

Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-10-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>

drm/i915: Init DRM connector polled field early

After an HPD IRQ storm on a connector intel_hpd_irq_storm_detect() will
set the connector's HPD pin state to HPD_MARK_DISABLED and the IRQ gets
disabled. Subsequently intel_hpd_irq_storm_switch_to_polling() will
enable polling for these connectors, setting the pin state to
HPD_DISABLED, but only if the connector's base.polled field is set to
DRM_CONNECTOR_POLL_HPD. intel_hpd_irq_storm_reenable_work() will
reenable the IRQ - after 2 minutes - if the pin state is HPD_DISABLED.

The connectors will be created with their base.polled field set to 0,
which gets initialized only later in i915_hpd_poll_init_work() (using
intel_connector::polled). If a storm is detected on a connector after
it's created and IRQs are enabled on it - by intel_hpd_init() - and
before its bease.polled field is initialized in the above work, the
connector's HPD pin will stay in the HPD_MARK_DISABLED state - leaving
the IRQ disabled indefinitely - and polling will not get enabled on it as
intended.

I can't see a reason for initializing base.polled in a delayed manner,
so do this already when creating the connector, to prevent the above
race condition.

Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-2-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>

drm/i915/tv: use DISPLAY_VER instead of GRAPHICS_VER

Display code should not care about graphics version. It's only comments
here, but update anyway.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240104174350.823605-5-jani.nikula@intel.com

drm/i915/tv: Fix TV mode

Commit 1fd4a5a36f9f ("drm/connector: Rename legacy TV property") failed
to update all the users of the struct drm_tv_connector_state mode field,
which resulted in a build failure in i915.

However, a subsequent commit in the same series reintroduced a mode
field in that structure, with a different semantic but the same type,
with the assumption that all previous users were updated.

Since that didn't happen, the i915 driver now compiles, but mixes
accesses to the legacy_mode field and the newer mode field, but with the
previous semantics.

This obviously doesn't work very well, so we need to update the accesses
that weren't in the legacy renaming commit.

Fixes: 1fd4a5a36f9f ("drm/connector: Rename legacy TV property")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220131251.453060-1-mripard@kernel.org
(cherry picked from commit bf7626f19d6ff14b9722273e23700400cc4d78ba)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915/tv: Drop redundant null checks

Neither 'tv_mode' or 'color_conversion' can be NULL,
so drop the pointless checks.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231207193441.20206-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Skip some timing checks on BXT/GLK DSI transcoders

Apparently some BXT/GLK systems have DSI panels whose timings
don't agree with the normal cpu transcoder hblank>=32 limitation.
This is perhaps fine as there are no specific hblank/etc. limits
listed for the BXT/GLK DSI transcoders.

Move those checks out from the global intel_mode_valid() into
into connector specific .mode_valid() hooks, skipping BXT/GLK
DSI connectors. We'll leave the basic [hv]display/[hv]total
checks in intel_mode_valid() as those seem like sensible upper
limits regardless of the transcoder used.

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9720
Fixes: 8f4b1068e7fc ("drm/i915: Check some transcoder timing minimum limits")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Skip some timing checks on BXT/GLK DSI transcoders

Apparently some BXT/GLK systems have DSI panels whose timings
don't agree with the normal cpu transcoder hblank>=32 limitation.
This is perhaps fine as there are no specific hblank/etc. limits
listed for the BXT/GLK DSI transcoders.

Move those checks out from the global intel_mode_valid() into
into connector specific .mode_valid() hooks, skipping BXT/GLK
DSI connectors. We'll leave the basic [hv]display/[hv]total
checks in intel_mode_valid() as those seem like sensible upper
limits regardless of the transcoder used.

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9720
Fixes: 8f4b1068e7fc ("drm/i915: Check some transcoder timing minimum limits")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit e0ef2daa8ca8ce4dbc2fd0959e383b753a87fd7d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: convert INTEL_DISPLAY_ENABLED() into a function

There's no need for this to be a macro. Add some documentation too.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/480b9b697b2ffa0c8677115bd443ba633801c6c1.1696336887.git.jani.nikula@intel.com

drm/i915/irq: split out display irq handling

Split (non-hotplug) display irq handling out of i915_irq.[ch] into
display/intel_display_irq.[ch].

v3:
- Preserve [I915_MAX_PIPES] harder (kernel test robot)

v2:
- Rebase
- Preserve [I915_MAX_PIPES] in functions (kernel test robot)

Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230515101738.2399816-3-jani.nikula@intel.com

drm/i915/display: Add new member to configure PCON color conversion

The decision to use DFP output format conversion capabilities should be
during compute_config phase.

This patch adds new member to crtc_state to represent the final
output_format to the sink. In case of a DFP this can be different than
the output_format, as per the format conversion done via the PCON.

This will help to store only the format conversion capabilities of the
DP device in intel_dp->dfp, and use crtc_state to compute and store the
configuration for color/format conversion for a given mode.

v2: modified the new member to crtc_state to represent the final
output_format that eaches the sink, after possible conversion by
PCON kind of devices. (Ville)

v3: Addressed comments from Ville:
-Added comments to clarify difference between sink_format and
output_format.
-Corrected the order of setting sink_format and output_format.
-Added readout for sink_format in get_pipe_config hooks.

v4: Set sink_format for intel_sdvo too. (Ville)

v5: Rebased.

v6: Fixed condition to go for YCbCr420 format for dp and hdmi. (Ville)

v7: Fix the condition to set sink_format for HDMI.
Set hdmi output_format simply as sink_format. (Ville)

Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-2-ankit.k.nautiyal@intel.com

drm/i915/display: throw out struct intel_load_detect_pipe

An error-valued pointer can handle all in one without the wrapper
struct.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230417153741.1074692-2-jani.nikula@intel.com

drm/i915/display: split out load detect to a separate file

Load detect is shared between tv and crt but otherwise isolated in
intel_display.c.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230417153741.1074692-1-jani.nikula@intel.com

drm/i915/tv: split out TV regs to a separate file

Clean up i915_reg.h by splitting out TV regs to display/intel_tv_regs.h.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/be4a946a7772f5b4483ad9e078cb62158849683e.1678973282.git.jani.nikula@intel.com

drm/i915/display/misc: use intel_de_rmw if possible

The helper makes the code more compact and readable.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230110113656.4050491-1-andrzej.hajda@intel.com

drm/connector: Rename drm_mode_create_tv_properties

drm_mode_create_tv_properties(), among other things, will create the
"mode" property that stores the analog TV mode that connector is
supposed to output.

However, that property is getting deprecated, so let's rename that
function to mention it's deprecated. We'll introduce a new variant of
that function creating the property superseeding it in a later patch.

Reviewed-by: Lyude Paul <lyude@redhat.com> # nouveau
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Tested-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Acked-in-principle-or-something-like-that-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://lore.kernel.org/r/20220728-rpi-analog-tv-properties-v10-4-256dad125326@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/connector: Rename legacy TV property

The current tv_mode has driver-specific values that don't allow to
easily share code using it, either at the userspace or kernel level.

Since we're going to introduce a new, generic, property that fit the
same purpose, let's rename this one to legacy_tv_mode to make it
obvious we should move away from it.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com> # nouveau
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Tested-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Acked-in-principle-or-something-like-that-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://lore.kernel.org/r/20220728-rpi-analog-tv-properties-v10-2-256dad125326@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/i915: stop including i915_irq.h from i915_trace.h

Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.

Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.

Also some places actually needed i915_irq.h too.

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com

drm/i915/display: remove drm_device aliases

drm_device pointers are unwelcome.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221006204844.2831303-1-andrzej.hajda@intel.com

drm/i915: Clean up connector->*_allowed setup

All the connectors are zero initialized so no need to clear
the *_allowed flags we don't support. Only leave the ones we want
to set. And while at it switch to booleans instead of ints.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Extract intel_tv_add_properties()

Pull all the TV connector property setup into its own neat function.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Fix TV encoder clock computation

The TV encoder has its own special clocking strategy,
which means we can't just use intel_crtc_dotclock() to
figure out what the resulting dotclock will be given
the actual DPLL port_clock. Additionally the DPLL can't
always generate exactly the frequency we initially asked
for. This results in us computing a bogus dotclock/etc.,
and it won't match the readout which is handled by the
encoder itself properly. Naturally the state checker
becomes unhappy with the mismatch.

To do this sanely we'll need to move the DPLL computation
into encoder->compute_config() so that all the derived
state gets correctly computed based on the actual DPLL
output frequency. Start doing that just for the TV encoder
initally as intel_crtc_dotclock() should be able to handle
other encoder types well enough. Though eventually this
should be done for all encoder types rather than
doing it from intel_crtc_compute_config().

With this we actually do some of the DPLL state computation
twice, but we can skip the second actual .find_dpll() search
by flagging .clock_set=true after we've done it once. We also
still need to avoid clobbering the correct
adjusted_mode.crtc_clock set up by encoder->compute_config()
when called a second time from intel_crtc_compute_config().

Fixes: 665a7b04092c ("drm/i915: Feed the DPLL output freq back into crtc_state")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220909205932.32537-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Use DRM_MODE_FMT+DRM_MODE_ARG()

Replace all drm_mode_debug_printmodeline() calls with
DRM_MODE_FMT+DRM_MODE_ARG(). Makes the debug output a bit more
terse in places where we previously had a newline in the precedeing
drm_dbg_kms(), and avoids anything else sneaking in between the two
printk()s in all cases.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323182935.4701-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/trace: split out display trace to a separate file

Add display/intel_display_trace.[ch] for defining display
tracepoints. The main goal is to reduce cross-includes between gem and
display. It would be possible split up tracing even further, but that
would lead to more boilerplate.

We end up having to include intel_crtc.h in a few places because it was
pulled in implicitly via intel_de.h -> i915_trace.h -> intel_crtc.h, and
that's no longer the case.

There should be no changes to tracepoints.

v3:
- Rebase

v2:
- Define TRACE_INCLUDE_PATH relative to define_trace.h (Chris)
- Remove useless comments (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7862ad764fbd0748d903c76bc632d3d277874e5b.1638961423.git.jani.nikula@intel.com

drm/i915/display: add intel_crtc_wait_for_next_vblank() and use it

intel_wait_for_vblank() goes through a pipe to crtc lookup, while in
most cases we already have the crtc available. Avoid the extra lookups
by adding an intel_crtc based helper.

v2:
- Add intel_crtc_wait_for_next_vblank() helper (Ville)

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/90cfbd8c3e79a742b0ee9e3ae75493acb0785dbb.1638366969.git.jani.nikula@intel.com

drm/i915: s/pipe/transcoder/ when dealing with PIPECONF/TRANSCONF

PIPECONF becamse TRANSCONF when HSW introduced the EDP transcoder.
Bigjoiner is making life even more confusing by introducing
a N:1 relationship between pipes and transcoders. In that case
we only enable/configure the transcoder corresponding to the
master pipe. Let's do some renames to make it clear we're dealing
with the transcoder rather than pipe when it comes to
PIPECONF/TRANSCONF.

I decided to leave the _cpu_ part out from the function/macro
names since the PCH transcoder related stuff already has a
_pch_ in their name. So shouldn't be possible to confuse them.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: s/intel_crtc/crtc/

Clear out the straggler 'intel_crtc' variables.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210609085632.22026-7-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915/display: replace IS_GEN() in commented code

Since we are replacing IS_GEN() with GRAPHICS_VER(), make sure we take
care of the comments as well.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210603165428.3625495-8-lucas.demarchi@intel.com

drm/i915: Don't include intel_de.h from intel_display_types.h

Hoist the intel_de.h include from intel_display_types.h one
level up. I need this in order to untangle the include order
so that I can add tracepoints into intel_de.h.

This little cocci script did most of the work for me:
@find@
@@
(
intel_de_read(...)
|
intel_de_read_fw(...)
|
intel_de_write(...)
|
intel_de_write_fw(...)
)

@has_include@
@@
(
#include "intel_de.h"
|
#include "display/intel_de.h"
)

@depends on find && !has_include@
@@
+ #include "intel_de.h"
#include "intel_display_types.h"

@depends on find && !has_include@
@@
+ #include "display/intel_de.h"
#include "display/intel_display_types.h"

Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com

drm/i915/display: rename display version macros

While converting the rest of the driver to use GRAPHICS_VER() and
MEDIA_VER(), following what was done for display, some discussions went
back on what we did for display:

1) Why is the == comparison special that deserves a separate
macro instead of just getting the version and comparing directly
like is done for >, >=, <=?

2) IS_DISPLAY_RANGE() is weird in that it omits the "_VER" for
brevity. If we remove the current users of IS_DISPLAY_VER(), we
could actually repurpose it for a range check

With (1) there could be an advantage if we used gen_mask since multiple
conditionals be combined by the compiler in a single and instruction and
check the result. However a) INTEL_GEN() doesn't use the mask since it
would make the code bigger everywhere else and b) in the cases it made
sense, it also made sense to convert to the _RANGE() variant.

So here we repurpose IS_DISPLAY_VER() to work with a [ from, to ] range
like was the IS_DISPLAY_RANGE() and convert the current IS_DISPLAY_VER()
users to use == and != operators. Aside from the definition changes,
this was done by the following semantic patch:

@@ expression dev_priv, E1; @@
- !IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) != E1

@@ expression dev_priv, E1; @@
- IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) == E1

@@ expression dev_priv, from, until; @@
- IS_DISPLAY_RANGE(dev_priv, from, until)
+ IS_DISPLAY_VER(dev_priv, from, until)

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Jani: Minor conflict resolve while applying.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210413051002.92589-4-lucas.demarchi@intel.com

drm/i915/display: Eliminate most usage of INTEL_GEN()

Use Coccinelle to convert most of the usage of INTEL_GEN() and IS_GEN()
in the display code to use DISPLAY_VER() comparisons instead. The
following semantic patch was used:

@@ expression dev_priv, E; @@
- INTEL_GEN(dev_priv) == E
+ IS_DISPLAY_VER(dev_priv, E)

@@ expression dev_priv; @@
- INTEL_GEN(dev_priv)
+ DISPLAY_VER(dev_priv)

@@ expression dev_priv; expression E; @@
- IS_GEN(dev_priv, E)
+ IS_DISPLAY_VER(dev_priv, E)

@@
expression dev_priv;
expression from, until;
@@
- IS_GEN_RANGE(dev_priv, from, until)
+ IS_DISPLAY_RANGE(dev_priv, from, until)

There are still some display-related uses of INTEL_GEN() in intel_pm.c
(watermark code) and i915_irq.c. Those will be updated separately.

v2:
- Use new IS_DISPLAY_RANGE and IS_DISPLAY_VER helpers. (Jani)

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-4-matthew.d.roper@intel.com

drm/i915: Reduce INTEL_DISPLAY_ENABLED to just treat outputs as disconnected

Since the display hardware is all there even when INTEL_DISPLAY_ENABLED
return false we have to be capable of shutting it down cleanly so
as to not anger the hw. To that end let's reduce the effect of
!INTEL_DISPLAY_ENABLE to just treating all outputs as disconnected.
Should prevent anyone from automagically enabling any of them, while
still allowing us to cleanly shut them down.

v2: Put the check into the right place for CRT

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910164256.25983-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Stop using mode->private_flags

Replace the use of mode->private_flags with a truly private bitmaks
in our own crtc state. We also need a copy in the crtc itself so the
vblank code can get at it. We already have scanline_offset in there
for a similar reason, as well as the vblank->hwmode which is assigned
via drm_calc_timestamping_constants(). Fortunately we now have a
nice place for doing the crtc_state->crtc copy in
intel_crtc_update_active_timings() which gets called both for
modesets and init/resume readout.

The one slightly iffy spot is the INHERITED flag which we want to
preserve until userspace/fb_helper does the first proper commit after
actually calling .detecti() on the connectors. Otherwise we don't have
the full sink capabilities (audio,infoframes,etc.) when .compute_config()
gets called and thus we will fail to enable those features when the
first userspace commit happens. The only internal commit we do prior to
that should be from intel_initial_commit() and there we can simply
preserve the INHERITED flag from the readout.

v2: Deal with INHERITED in sanitize_watermarks() as well

CC: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429103904.11727-1-ville.syrjala@linux.intel.com

drm: Nuke mode->vrefresh

Get rid of mode->vrefresh and just calculate it on demand. Saves
a bit of space and avoids the cached value getting out of sync
with reality.

Mostly done with cocci, with the following manual fixups:
- Remove the now empty loop in drm_helper_probe_single_connector_modes()
- Fix __MODE() macro in ch7006_mode.c
- Fix DRM_MODE_ARG() macro in drm_modes.h
- Remove leftover comment from samsung_s6d16d0_mode
- Drop the TODO

@@
@@
struct drm_display_mode {
...
- int vrefresh;
...
};

@@
identifier N;
expression E;
@@
struct drm_display_mode N = {
- .vrefresh = E
};

@@
identifier N;
expression E;
@@
struct drm_display_mode N[...] = {
...,
{
- .vrefresh = E
}
,...
};

@@
expression E;
@@
{
DRM_MODE(...),
- .vrefresh = E,
}

@@
identifier M, R;
@@
int drm_mode_vrefresh(const struct drm_display_mode *M)
{
...
- if (M->vrefresh > 0)
- R = M->vrefresh;
- else
if (...) {
...
}
...
}

@@
struct drm_display_mode *p;
expression E;
@@
(
- p->vrefresh = E;
|
- p->vrefresh
+ drm_mode_vrefresh(p)
)

@@
struct drm_display_mode s;
expression E;
@@
(
- s.vrefresh = E;
|
- s.vrefresh
+ drm_mode_vrefresh(&s)
)

@@
expression E;
@@
- drm_mode_vrefresh(E) ? drm_mode_vrefresh(E) : drm_mode_vrefresh(E)
+ drm_mode_vrefresh(E)

@find_substruct@
identifier X;
identifier S;
@@
struct X {
...
struct drm_display_mode S;
...
};

@@
identifier find_substruct.S;
expression E;
identifier I;
@@
{
.S = {
- .vrefresh = E
}
}

@@
identifier find_substruct.S;
identifier find_substruct.X;
expression E;
identifier I;
@@
struct X I[...] = {
...,
.S = {
- .vrefresh = E
}
,...
};

v2: Drop TODO
v3: Rebase
v4: Rebase

Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jerry Han <hanxu5@huaqin.corp-partner.google.com>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Stefan Mavrodiev <stefan@olimex.com>
Cc: Robert Chiras <robert.chiras@nxp.com>
Cc: "Guido Günther" <agx@sigxcpu.org>
Cc: Purism Kernel Team <kernel@puri.sm>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428171940.19552-4-ville.syrjala@linux.intel.com

drm/i915: Pass atomic state to encoder hooks

We're going to want access to the atomic state for iterating
the slave crtcs when enabling the port sync master crtc. Pass
the atomic state all the way down.

The alternative would be yet another encoder hook which we'll
have to call after all the normal modeset stuff is done. Not
really a fan of yet another hook just for this.

Note that during readout state sanitation we are now going
to pass NULL as the atomic state since we don't have one.
We need to change that and then we can also s/crtc_state/crtc/
and s/conn_state/conn/ for the encoder hooks as well.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-13-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915/tv: use struct drm_device based logging

Convert all the DRM_* logging macros to the struct drm_device based
macros to provide device specific logging.

No functional changes.

Generated using the following semantic patch, originally written by
Wambui Karuga <wambui.karugax@gmail.com>, with manual fixups on top:

@@
identifier fn, T;
@@

fn(...,struct drm_i915_private *T,...) {
<+...
(
-DRM_INFO(
+drm_info(&T->drm,
...)
|
-DRM_NOTE(
+drm_notice(&T->drm,
...)
|
-DRM_ERROR(
+drm_err(&T->drm,
...)
|
-DRM_WARN(
+drm_warn(&T->drm,
...)
|
-DRM_DEBUG_DRIVER(
+drm_dbg(&T->drm,
...)
|
-DRM_DEBUG_KMS(
+drm_dbg_kms(&T->drm,
...)
|
-DRM_DEBUG_ATOMIC(
+drm_dbg_atomic(&T->drm,
...)
)
...+>
}

@@
identifier fn, T;
@@

fn(...) {
...
struct drm_i915_private *T = ...;
<+...
(
-DRM_INFO(
+drm_info(&T->drm,
...)
|
-DRM_NOTE(
+drm_notice(&T->drm,
...)
|
-DRM_ERROR(
+drm_err(&T->drm,
...)
|
-DRM_WARN(
+drm_warn(&T->drm,
...)
|
-DRM_DEBUG_DRIVER(
+drm_dbg(&T->drm,
...)
|
-DRM_DEBUG_KMS(
+drm_dbg_kms(&T->drm,
...)
|
-DRM_DEBUG_ATOMIC(
+drm_dbg_atomic(&T->drm,
...)
)
...+>
}

Cc: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e08dbd1933e1dbbd8e9f1954f5b0a9db946c4e7d.1584714939.git.jani.nikula@intel.com

drm/i915: significantly reduce the use of <drm/i915_drm.h>

The #include has been splattered all over the place, but there are
precious few places, all .c files, that actually need it.

v2: remove leftover double newlines

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225133131.3301-1-jani.nikula@intel.com

drm/i915/tv: automatic conversion to drm_device based logging macros.

Converts most uses of the printk based logging macros to the struct
drm_device based logging macros in i915/display/intel_tv.c using the
following coccinelle script that matches based on the existence of a
drm_i915_private device pointer:
@@
identifier fn, T;
@@

fn(...) {
...
struct drm_i915_private *T = ...;
<+...
(
-DRM_INFO(
+drm_info(&T->drm,
...)
|
-DRM_ERROR(
+drm_err(&T->drm,
...)
|
-DRM_WARN(
+drm_warn(&T->drm,
...)
|
-DRM_DEBUG(
+drm_dbg(&T->drm,
...)
|
-DRM_DEBUG_KMS(
+drm_dbg_kms(&T->drm,
...)
|
-DRM_DEBUG_DRIVER(
+drm_dbg(&T->drm,
...)
|
-DRM_DEBUG_ATOMIC(
+drm_dbg_atomic(&T->drm,
...)
)
...+>
}

@@
identifier fn, T;
@@

fn(...,struct drm_i915_private *T,...) {
<+...
(
-DRM_INFO(
+drm_info(&T->drm,
...)
|
-DRM_ERROR(
+drm_err(&T->drm,
...)
|
-DRM_WARN(
+drm_warn(&T->drm,
...)
|
-DRM_DEBUG(
+drm_dbg(&T->drm,
...)
|
-DRM_DEBUG_DRIVER(
+drm_dbg(&T->drm,
...)
|
-DRM_DEBUG_KMS(
+drm_dbg_kms(&T->drm,
...)
|
-DRM_DEBUG_ATOMIC(
+drm_dbg_atomic(&T->drm,
...)
)
...+>
}

Checkpatch warnings were fixed manually.

Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200130083229.12889-6-wambui.karugax@gmail.com

drm/i915/tv: use intel_de_*() functions for register access

The implicit "dev_priv" local variable use has been a long-standing pain
point in the register access macros I915_READ(), I915_WRITE(),
POSTING_READ(), I915_READ_FW(), and I915_WRITE_FW().

Replace them with the corresponding new display engine register
accessors intel_de_read(), intel_de_write(), intel_de_posting_read(),
intel_de_read_fw(), and intel_de_write_fw().

No functional changes.

Generated using the following semantic patch:

@@
expression REG, OFFSET;
@@
- I915_READ(REG)
+ intel_de_read(dev_priv, REG)

@@
expression REG, OFFSET;
@@
- POSTING_READ(REG)
+ intel_de_posting_read(dev_priv, REG)

@@
expression REG, OFFSET;
@@
- I915_WRITE(REG, OFFSET)
+ intel_de_write(dev_priv, REG, OFFSET)

@@
expression REG;
@@
- I915_READ_FW(REG)
+ intel_de_read_fw(dev_priv, REG)

@@
expression REG, OFFSET;
@@
- I915_WRITE_FW(REG, OFFSET)
+ intel_de_write_fw(dev_priv, REG, OFFSET)

Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e6238e75f5a4155b1021736937b1fd7a0756a00.1579871655.git.jani.nikula@intel.com

drm/i915: Pass intel_connector to intel_attached_*()

Life is usually easier when we pass around intel_ types instead
of drm_ types. In this case it might not be, but I think being
consistent is a good thing anyway. Also some of this might get
cleaned up a bit more later as we keep propagating the intel_
types further.

@find@
identifier F =~ "^intel_attached_.*";
identifier C;
@@
F(struct drm_connector *C)
{
...
}

@@
identifier find.F;
identifier find.C;
@@
F(
- struct drm_connector *C
+ struct intel_connector *connector
)
{
<...
- C
+ &connector->base
...>
}

@@
identifier find.F;
expression C;
@@
- F(C)
+ F(to_intel_connector(C))

@@
expression C;
@@
- to_intel_connector(&C->base)
+ C

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-3-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>

drm/i915: Pass cpu_transcoder to assert_pipe_disabled() always

I missed a few assert_pipe_disabled() cases when changing it to
take enum transcoder instead of enum pipe, making sparse unhappy.
Convert the leftovers.

Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108145616.7349-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Perform automated conversions for crtc uapi/hw split, base -> uapi.

Split up crtc_state->base to uapi. This is done using the following patch,
ran after the previous commit that splits out any hw references:

@@
struct intel_crtc_state *T;
@@
-T->base
+T->uapi

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-5-maarten.lankhorst@linux.intel.com

drm/i915: Perform automated conversions for crtc uapi/hw split, base -> hw.

Split up crtc_state->base to hw where appropriate. This is done using the following patch:

@@
struct intel_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-T->base.x
+T->hw.x

@@
struct drm_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-to_intel_crtc_state(T)->base.x
+to_intel_crtc_state(T)->hw.x

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-4-maarten.lankhorst@linux.intel.com

drm/i915: Simplify pipe_mask setup even further

Just set pipe_mask=~0 for the non-special cases where any pipe
will do. intel_encoder_possible_crtcs() will anyway drop out
anything that doesn't exist.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002162505.30716-5-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>

drm/i915: s/crtc_mask/pipe_mask/

Rename the encoder->crtc_mask to encoder->pipe_mask to better
reflect what it actually contains.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002162505.30716-3-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>

drm/i915: Nuke 'mode' argument to intel_get_load_detect_pipe()

We always pass mode==NULL to intel_get_load_detect_pipe(). Remove
the pointless function argument.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029132323.18113-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Clean up encoder->crtc_mask setup

Use BIT(pipe) for better legibility when populating the crtc_mask
for encoders.

Also remove the redundant possible_crtcs setup for the TV encoder.

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708162048.4286-11-ville.syrjala@linux.intel.com

drm/i915: Polish intel_tv_mode_valid()

Drop the tv_mode NULL check since intel_tv_mode_find() never
actually returns NULL, and flip the condition around so that
the MODE_OK case is at the end, which is customary to all
the other .mode_valid() implementations.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191001154629.11063-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: rename intel_drv.h to display/intel_display_types.h

Everything about the file is about display, and mostly about types
related to display. Move under display/ as intel_display_types.h to
reflect the facts.

There's still plenty to clean up, but start off with moving the file
where it logically belongs and naming according to contents.

v2: fix the include guard name in the renamed file

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190806113933.11799-1-jani.nikula@intel.com

drm/i915: move modesetting output/encoder code under display/

Add a new subdirectory for display code, and start off by moving
modesetting output/encoder code. Judging by the include changes, this is
a surprisingly clean operation.

v2:
- move intel_sdvo_regs.h too
- use tabs for Makefile file lists and sort them

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190613084416.6794-2-jani.nikula@intel.com