drm/i915: Disable hotplug detection handlers during driver init/shutdown

As described in the previous two patches an unexpected connector
detection can happen during the init/shutdown sequences. Prevent these
by returning the connector's current status from the detection handlers.

Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-10-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>

drm/i915/display: Move panel_use_ssc module parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-8-jouni.hogander@intel.com

drm/i915: convert INTEL_DISPLAY_ENABLED() into a function

There's no need for this to be a macro. Add some documentation too.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/480b9b697b2ffa0c8677115bd443ba633801c6c1.1696336887.git.jani.nikula@intel.com

drm/i915: Relocate is_in_vrr_range()

Move is_in_vrr_range() into intel_vrr.c in anticipation of
more users, and rename it accordingly.

Cc: Manasi Navare <navaremanasi@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901130440.2085-8-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <navaremanasi@chromium.org>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>

drm/i915: Namespace pfit registers properly

Give the PFIT_CONTROL bits a consistent namespace.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230418175528.13117-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Use REG_BIT() & co for the pre-ilk pfit registers

Modernize the gmch pfit register definitions using REG_BIT/etc.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230418175528.13117-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Allow arbitrary refresh rates with VRR eDP panels

If the panel supports VRR it must be capable of accepting
timings with arbitrary vblank length, within the valid VRR
range. Use that fact to allow the user to request any refresh
rate they like. We simply pick the next highest fixed mode
from our list, and adjust the vblank to get the desired refresh
rate in the end.

Of course currently everything to do with the vrefresh is
using 1Hz precision, so might not be exact. But we can improve
that in the future by just upping our vrefresh precision.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230404175431.23064-1-ville.syrjala@linux.intel.com
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>

drm/i915/lvds: Extract intel_lvds_regs.h

Extract the integrated LVDS port register definitions
into their own header file.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130180540.8972-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/panel: move panel fixed EDID to struct intel_panel

It's a bit confusing to have two cached EDIDs in struct intel_connector
with slightly different purposes. Make the distinction a bit clearer by
moving the EDID cached for eDP and LVDS panels at connector init time to
struct intel_panel, and name it fixed_edid. That's what it is, a fixed
EDID for the panels.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/328350ef918638928a8286cdbab3107c8258332d.1674643465.git.jani.nikula@intel.com

drm/i915: Try to use the correct power sequencer intiially on bxt/glk

Currently on bxt/glk we just grab the power sequencer index from
the VBT data even though it may not have been parsed yet. That
could lead us to using the incorrect power sequencer during the
initial panel probe.

To avoid that let's try to read out the current state of the
power sequencer from the hardware. Unfortunately the power
sequencer no longer has anything in its registers to associate
it with the port, so the best we can do is just iterate through
the power sequencers and pick the first one. This should be
sufficient for single panel cases.

For the dual panel cases we probably need to go back to
parsing the VBT before the panel probe (and hope that
panel_type=0xff is never a thing in those cases). To that
end the code always prefers the VBT panel sequencer, if
available.

v2: Restructure a bit for upcoming icp+ dual PPS support

Cc: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125173156.31689-5-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>

drm/i915: Do panel VBT init early if the VBT declares an explicit panel type

Lots of ADL machines out there with bogus VBTs that declare
two eDP child devices. In order for those to work we need to
figure out which power sequencer to use before we try the EDID
read. So let's do the panel VBT init early if we can, falling
back to the post-EDID init otherwise.

The post-EDID init panel_type=0xff approach of assuming the
power sequencer should already be enabled doesn't really work
with multiple eDP panels, and currently we just end up using
the same power sequencer for both eDP ports, which at least
confuses the wakeref tracking, and potentially also causes us
to toggle the VDD for the panel when we should not.

Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125173156.31689-3-ville.syrjala@linux.intel.com

drm/i915: Introduce intel_panel_init_alloc()

Introduce a place where we can initialize connector->panel
after it's been allocated. We already have a intel_panel_init()
so had to get creative with the name and came up with
intel_panel_init_alloc().

Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125173156.31689-2-ville.syrjala@linux.intel.com

drm/i915: stop including i915_irq.h from i915_trace.h

Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.

Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.

Also some places actually needed i915_irq.h too.

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com

drm/i915: Allow panel fixed modes to have differing sync polarities

Apparently some panels declare multiple modes with random
sync polarities. Seems a bit weird, but looks like Windows/GOP
doesn't care, so let follow suit and accept alternate fixed
modes regardless of their sync polarities.

v2: Don't pollute the DRM_ namespace with a define (Jani)

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6968
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221020093938.27200-1-ville.syrjala@linux.intel.com

drm/i915: Setup final panel drrs_type already during init

Now that we track the VBT drrs type per-panel we can move the
has_drrs_modes() check to the panel init rather than doing it
for every intel_panel_drrs_type() call.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221003113249.16213-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Tighten DRRS capability reporting

Only report DRRS capability for the connector if its fixed_modes
list contains at least two modes capable of seamless DRRS switch
between them.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221003113249.16213-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Simplify intel_panel_add_edid_alt_fixed_modes()

Since commit a5810f551d0a ("drm/i915: Allow more varied alternate
fixed modes for panels") intel_panel_add_edid_alt_fixed_modes()
no longer considers vrr vs. drrs separately. So no reason to
pass them as separate parameters either.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220927180615.25476-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Simplify intel_panel_add_edid_alt_fixed_modes()

Since commit a5810f551d0a ("drm/i915: Allow more varied alternate
fixed modes for panels") intel_panel_add_edid_alt_fixed_modes()
no longer considers vrr vs. drrs separately. So no reason to
pass them as separate parameters either.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220927180615.25476-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit eb89e83c152b122a94e79527d63cb7c79823c37e)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Add intel_panel_highest_mode()

Add a function to get the fixed_mode with the highest clock.
The plan is to use this for the link bw calculation on seamless
DRRS panels so that we alwasy end up with the same link params
regardless of the requested refresh rate. This will allow fastset
to do seamless refresh rate changes based on userspace request
instead of having to go for a full modeset.

TODO: the function name isn't great

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907091057.11572-15-ville.syrjala@linux.intel.com

drm/i915: Allow more varied alternate fixed modes for panels

On some systems the panel reports alternate modes with
different blanking periods. If the EDID reports them and VBT
doesn't tell us otherwise then I can't really see why they
should be rejected. So allow their use for the purposes of
static DRRS.

For seamless DRRS we still require a much more exact match
of course. But that logic only kicks in when selecting the
downclock mode (or in the future when determining whether
we can do a seamless refresh rate change due to a user
modeset).

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6374
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220830212436.2021-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/quirks: abstract checking for display quirks

Add intel_has_quirk() for checking if a display quirk is present. Avoid
accessing i915->quirks all over the place.

v2: Rebase

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/74f954ca81a8068033141a15686dffd01ad9b0f9.1661779055.git.jani.nikula@intel.com

drm/i915: move vbt to display.vbt

Move display VBT related members under drm_i915_private display
sub-struct.

v2: Rebase

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/db4b648b201ea0b79654fec2028120999a735db0.1661779055.git.jani.nikula@intel.com

drm/i915: Accept more fixed modes with VRR panels

It seem that when dealing with VRR capable eDP panels we need
to accept fixed modes with variable vblank length (which is what
VRR varies dynamically). Typically the preferred mode seems to be
a non-VRR more (lowish dotclock/refresh rate + short vblank).

We also have examples where it looks like even the hblank length
is a bit different between the preferred mode vs. VRR mode(s).
So let's just accept anything that has matching hdisp+vdisp+flags.

v2: Document that is_alt_drrs_mode() is a subset of is_alt_vrr_mode() (Jani)

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/125
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220531191844.11313-4-ville.syrjala@linux.intel.com

drm/i915: Print out rejected fixed modes

To help with debugging DRRS/VRR panel init let's dump out all
the fixed modes we rejected for whatever reason.

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220531191844.11313-3-ville.syrjala@linux.intel.com

drm/i915/bios: Split VBT data into per-panel vs. global parts

Move the panel specific VBT parsing to happen during the
output probing stage. Needs to be done because the VBT
parsing will need to look at the EDID to determine
the correct panel_type on some machines.

We split the parsed VBT data (i915->vbt) along the same
boundary. For the moment we just hoist all the panel
specific stuff into connector->panel.vbt since that seems
like the most convenient place for eg. the backlight code.

Note that we simply drop the drrs type check from
intel_drrs_frontbuffer_update() since that operates on the whole
device rather than a specific connector/encoder. But the check
was just a micro optimization so removing it doesn't actually
mattter for correctness.

TODO: Lot's of cleanup to be done in the future. Eg. most of
the DSI stuff could probably be eliminated entirely and just
parsed on demand during DSI init.

v2: Note the intel_drrs_frontbuffer_update() change

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510104242.6099-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Respect VBT seamless DRRS min refresh rate

Make sure our choice of downclock mode respects the VBT
seameless DRRS min refresh rate limit.

v2: s/vrefesh/vrefresh/ (Jani)

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220504150440.13748-10-ville.syrjala@linux.intel.com

drm/i915: Allow higher refresh rate alternate fixed modes

We shouldn't restrict ourselves to just downclock modes with
lower refresh rate than the preferred mode. Laptops these
days can offer higher refresh rate modes as well.

Remove the arbitrary limit and allow all modes that, apart
from the clock, match the preferred mode.

v2: s/add_edid_downclock_modes/add_edid_alt_fixed_modes/ (Jani)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331112822.11462-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Allow an arbitrary number of downclock modes

Remove the "two fixed modes only" limit and grab as many
downclock modes from the EDID as we can find.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331112822.11462-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Stop duplicating the EDID fixed/downclock modes

Instead of duplicating the fixed/downclock modes we can just grab
the originals straight from the probed_modes list and keep them.
The next .get_modes() is going to repopulate the probed_modes list
anyway so whatever we leave there is just going to sit around until
that time wasting memory. In fact let's clear out the probed modes
list entirely to make sure we get 100% consistent behaviour starting
already from the very first real .get_modes().

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331112822.11462-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Combine the EDID fixed_mode+downclock_mode lookup into one

The intel_panel_add_edid_fixed_mode() vs.
intel_panel_add_edid_downclock_mode() split is not really
helpful. Let's just roll those into a single function so
that the connector init code doesn't have to care too much
about this. All we need to know is whether DRRS should be
allowed or not.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331112822.11462-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Nuke intel_drrs_init()

intel_drrs_init() is a mostly pointless wrapper around
intel_panel_add_edid_downclock_mode(), get rid of it.

The only really useful thing left in there is the debug
print regarding the DRRS type supported by the connector.
Let's just move that into intel_panel_init().

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331112822.11462-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Refactor non-EDID fixed mode duplication

All the non-EDID fixed mode functions basically do the exact
same thing. Let's refactor the common bits into a shared
function.

There are minor differences on how the mode types are populated,
whether the display info physical size is updated, and the debug
print. The differences are purely accidental, so unifying them is
actually a good thing.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331112822.11462-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Put fixed modes directly onto the panel's fixed_modes list

Rather than having the connector init get the fixed mode back from
intel_panel and then feed it straight back into intel_panel_init()
let's just make the fixed mode lookup put the mode directly onto
the panel's fixed_modes list. Avoids the pointless round trip and
opens the door for further enhancements to the fixed mode handling.

v2: Make the debug message correct by using intel_panel_drrs_type() (Jani)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331112822.11462-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Extract intel_panel_encoder_fixed_mode()

Apart from the EDID and VBT based mechanism we also sometimes
use the encoder's current mode as the panel fixed mode. We
currently have the same code for that duplicated in two places.
Let's unify.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323182935.4701-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Extract intel_panel_vbt_sdvo_fixed_mode()

We have a function for duplicating the VBT LFP mode. Add the same
for the VBT SDVO mode.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323182935.4701-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Rename intel_panel_vbt_fixed_mode()

Rename intel_panel_vbt_fixed_mode() to
intel_panel_vbt_lfp_fixed_mode() to be more descriptive.
We'll have another VBT fixed mode function soon and we
don't want to confuse the two.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323182935.4701-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Use DRM_MODE_FMT+DRM_MODE_ARG()

Replace all drm_mode_debug_printmodeline() calls with
DRM_MODE_FMT+DRM_MODE_ARG(). Makes the debug output a bit more
terse in places where we previously had a newline in the precedeing
drm_dbg_kms(), and avoids anything else sneaking in between the two
printk()s in all cases.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323182935.4701-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Pass intel_connector to intel_panel_{init,fini}()

All the other intel_panel functions take struct intel_connector,
so might as well make init()/fini() take one as well.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323182935.4701-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Convert fixed_mode/downclock_mode into a list

Store the fixed_mode and downclock_mode as a real list,
in preparation for exposing other supported modes as well.

v2: Init the list in intel_sdvo_connector_alloc() too
v3: Use list_first_entry_or_null() (Jani)

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220314152737.9125-1-ville.syrjala@linux.intel.com

drm/i915: Implement static DRRS

Let's start supporting static DRRS by trying to match the refresh
rate the user has requested, assuming the panel supports suitable
timings.

For now we stick to just our current two timings:
- fixed_mode: the panel's preferred mode
- downclock_mode: the lowest refresh rate mode we found
Some panels may support more timings than that, but we'll
have to convert our fixed_mode/downclock_mode pointers
into a full list before we can handle that.

v2: Rebase due to intel_panel_get_modes()

Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220311172428.14685-16-ville.syrjala@linux.intel.com

drm/i915: Introduce intel_panel_drrs_type()

Add a helper to determine which type of DRRS the panel supports.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220311172428.14685-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Introduce intel_panel_preferred_fixed_mode()

There are a couple of cases where we essentially just want to
get/check the preferred fixed mode of the panel. Add a small
helper for that to abstract away the direct pointer lookup.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220311172428.14685-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Introduce intel_panel_get_modes()

Several connectors want to return the fixed_mode from .get_modes(),
add a helper to do that (and hide the details inside intel_panel.c).

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220311172428.14685-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Introduce intel_panel_{fixed,downclock}_mode()

Abstract away the details on where we store the fixed/downclock
modes, and also how we select them. Will be useful for static
DRRS (aka. allowing the user to select the refresh rate for the
panel).

We pass in the user requested mode to intel_panel_fixed_mode()
so that in the future it may try to match the refresh rate.
And intel_panel_downclock_mode() gets passed the adjusted_mode
we actually chose to use so that it may find a suitable lower
resresh rate variant.

v2: Hook it up for all encoders
s/fixed_mode/adjusted_mode/ in intel_panel_downclock_mode() (Jani)
Elaborate on the choice or arguments for the functions (Jani)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220311172428.14685-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Start tracking PIPESRC as a drm_rect

Instead of just having the pipe_src_{w,h} let's use a full
drm_rect for it. This will be particularly useful to astract
away some bigjoiner details.

v2: No hweight() stuff yet

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223131315.18016-11-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>

drm/i915: Reject user modes that don't match fixed mode's refresh rate

When using a panel with a fixed mode we don't change the refresh
rate of the display. Reject any user requested mode which doesn't
match that fixed refresh rate.

Unfortunately when Xorg sees the scaling_mode property on the
connecor it likes to automagically cook up modes whose refresh
rate is a fair bit off from the fixed refresh rate we use. So
we have to give it some extra latitude so that we don't start to
reject all of it.

v2: sDVO now uses intel_panel_compute_config() too
v3: Add a debug message to inform the user what happened

References: https://gitlab.freedesktop.org/drm/intel/-/issues/2939
References: https://gitlab.freedesktop.org/drm/intel/-/issues/3969
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929184536.8332-1-ville.syrjala@linux.intel.com

drm/i915: Introduce intel_panel_compute_config()

Let's introduce a compute_config() helper for fixed mode panels.
For now all it does is the fixed_mode->adjusted_mode copy.

Note that with sDVO we have to ask the external encoder chip
to spit out our actual display timings for us, so the fixed_mode
to adjusted_mode copy done by intel_panel_compute_config() is
redundant, but we still want to use it to do other checks for us
later. We'll be fine so long as we only call it before
intel_sdvo_get_preferred_input_mode() overwrites adjusted_mode
with the timings from the encoder.

v2: Use intel_panel_compute_config() with sDVO

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210927185207.13620-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Reject modes that don't match fixed_mode vrefresh

When using a fixed mode we won't change the refresh rate ever.
So filter out all modes that don't match the fixed_mode's refresh
rate.

I'm going to declare the "rounded to nearest Hz refresh
rates must match" approach good enough for now.

Note that we could start supporting multiple refresh rates
with panels that can do it, but that would mean replacing
the single fixed mode concept with a list of fixed modes.
Then we could look for the closest match to the user's
requested refresh rate and use that. But all of that would
be a fair bit of work so we'll leave it for later.

References: https://gitlab.freedesktop.org/drm/intel/-/issues/2939
References: https://gitlab.freedesktop.org/drm/intel/-/issues/3969
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210923200109.4459-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Extract intel_panel_mode_valid()

Extract intel_panel_mode_valid() from the eDP code to a generic helper.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210923200109.4459-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/panel: mass rename functions to have intel_panel_ prefix

Follow the usual naming conventions. Also pull HAS_GMCH() check to
intel_panel_fitting(). No functional changes.

Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9ff6e42e377bdb0c9349f50d9ea79671059633c7.1629888677.git.jani.nikula@intel.com

drm/i915/backlight: mass rename functions to have intel_backlight_ prefix

Follow the usual naming conventions. As a drive-by cleanup, also pass
intel_connector instead of drm_connector to intel_backlight_setup(). No
functional changes.

Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ea1c22370210abdd4f5547af73c71b902061ea50.1629888677.git.jani.nikula@intel.com

drm/i915/backlight: extract backlight code to a separate file

In a long overdue refactoring, split out backlight code to new
intel_backlight.[ch]. Simple code movement, leave renames for follow-up
work. No functional changes.

Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/97d310848f03061473b9b2328e2c5c4dcf263cfa.1629888677.git.jani.nikula@intel.com

drm/i915/panel: move intel_panel_use_ssc() out of headers

There's no performance reason to have it as static inline; move it out
of intel_display_types.h to reduce clutter and dependency on i915_drv.h.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6f2c05005e4fa43a5572b02b3f41363725ffdb4f.1629281426.git.jani.nikula@intel.com

drm/i915: Don't include intel_de.h from intel_display_types.h

Hoist the intel_de.h include from intel_display_types.h one
level up. I need this in order to untangle the include order
so that I can add tracepoints into intel_de.h.

This little cocci script did most of the work for me:
@find@
@@
(
intel_de_read(...)
|
intel_de_read_fw(...)
|
intel_de_write(...)
|
intel_de_write_fw(...)
)

@has_include@
@@
(
#include "intel_de.h"
|
#include "display/intel_de.h"
)

@depends on find && !has_include@
@@
+ #include "intel_de.h"
#include "intel_display_types.h"

@depends on find && !has_include@
@@
+ #include "display/intel_de.h"
#include "display/intel_display_types.h"

Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com

drm/i915/backlight: use unique backlight device names

Registering multiple backlight devices with intel_backlight name will
obviously fail, regardless of whether they're two connectors in the same
drm device or two different drm devices.

It would be preferrable to switch to completely unique names, and sunset
the generic intel_backlight name. However, there are apparently users
out there that hardcode the name, so the change would break backward
compatibility.

As a compromise, register the first device with intel_backlight name. In
the common case, this is the only backlight device anyway. From the
second device on, use card%d-%s-backlight format, for example
card0-eDP-2-backlight, to make the name unique.

This approach does not preclude us from registering the first device
using the same naming scheme in the future.

v2: Keep using intel_backlight name for first backlight device

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2794
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7dc3f6974711ce44522189dc9db05d1e6e24e6d8.1619604743.git.jani.nikula@intel.com

drm/i915/backlight: clean up backlight device register

Add connector and backlight device name to logging, and propagate error
code from backlight_device_register() instead of flattening to
-ENODEV. Storing the name in an allocated buffer is unnecessary here,
but makes follow-up work on names much cleaner.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/271206461d9c0f42755792236330b588df3b532e.1619604743.git.jani.nikula@intel.com

drm/i915/display: rename display version macros

While converting the rest of the driver to use GRAPHICS_VER() and
MEDIA_VER(), following what was done for display, some discussions went
back on what we did for display:

1) Why is the == comparison special that deserves a separate
macro instead of just getting the version and comparing directly
like is done for >, >=, <=?

2) IS_DISPLAY_RANGE() is weird in that it omits the "_VER" for
brevity. If we remove the current users of IS_DISPLAY_VER(), we
could actually repurpose it for a range check

With (1) there could be an advantage if we used gen_mask since multiple
conditionals be combined by the compiler in a single and instruction and
check the result. However a) INTEL_GEN() doesn't use the mask since it
would make the code bigger everywhere else and b) in the cases it made
sense, it also made sense to convert to the _RANGE() variant.

So here we repurpose IS_DISPLAY_VER() to work with a [ from, to ] range
like was the IS_DISPLAY_RANGE() and convert the current IS_DISPLAY_VER()
users to use == and != operators. Aside from the definition changes,
this was done by the following semantic patch:

@@ expression dev_priv, E1; @@
- !IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) != E1

@@ expression dev_priv, E1; @@
- IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) == E1

@@ expression dev_priv, from, until; @@
- IS_DISPLAY_RANGE(dev_priv, from, until)
+ IS_DISPLAY_VER(dev_priv, from, until)

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Jani: Minor conflict resolve while applying.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210413051002.92589-4-lucas.demarchi@intel.com

drm/i915/display: Eliminate IS_GEN9_{BC,LP}

Now that we've eliminated INTEL_GEN(), IS_GEN_RANGE(), etc. from the
display code, we should also kill off our use of the IS_GEN9_* macros
too. We'll do the conversion manually this time instead of using
Coccinelle since the most logical substitution can depend heavily on the
code context, and sometimes we can keep the code simpler if we make
additional adjustments such as swapping the order of if/else arms.

v2:
- Restore a lost negation in intel_pll_is_valid().

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210407203945.1432531-1-matthew.d.roper@intel.com
(cherry picked from commit 70bfb30743d5da73058b0a2271e9c127a84fb494)
[Jani: cherry picked to topic branch to reduce conflicts]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/display: Eliminate IS_GEN9_{BC,LP}

Now that we've eliminated INTEL_GEN(), IS_GEN_RANGE(), etc. from the
display code, we should also kill off our use of the IS_GEN9_* macros
too. We'll do the conversion manually this time instead of using
Coccinelle since the most logical substitution can depend heavily on the
code context, and sometimes we can keep the code simpler if we make
additional adjustments such as swapping the order of if/else arms.

v2:
- Restore a lost negation in intel_pll_is_valid().

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210407203945.1432531-1-matthew.d.roper@intel.com

drm/i915/display: Eliminate most usage of INTEL_GEN()

Use Coccinelle to convert most of the usage of INTEL_GEN() and IS_GEN()
in the display code to use DISPLAY_VER() comparisons instead. The
following semantic patch was used:

@@ expression dev_priv, E; @@
- INTEL_GEN(dev_priv) == E
+ IS_DISPLAY_VER(dev_priv, E)

@@ expression dev_priv; @@
- INTEL_GEN(dev_priv)
+ DISPLAY_VER(dev_priv)

@@ expression dev_priv; expression E; @@
- IS_GEN(dev_priv, E)
+ IS_DISPLAY_VER(dev_priv, E)

@@
expression dev_priv;
expression from, until;
@@
- IS_GEN_RANGE(dev_priv, from, until)
+ IS_DISPLAY_RANGE(dev_priv, from, until)

There are still some display-related uses of INTEL_GEN() in intel_pm.c
(watermark code) and i915_irq.c. Those will be updated separately.

v2:
- Use new IS_DISPLAY_RANGE and IS_DISPLAY_VER helpers. (Jani)

Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-4-matthew.d.roper@intel.com

drm/i915: Remove references to struct drm_device.pdev

Using struct drm_device.pdev is deprecated. Convert i915 to struct
drm_device.dev. No functional changes.

v6:
* also remove assignment in selftests/ in a later patch (Chris)
v5:
* remove assignment in later patch (Chris)
v3:
* rebased
v2:
* move gt/ and gvt/ changes into separate patches

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128133127.2311-2-tzimmermann@suse.de

drm/i915/dp: Enable Intel's HDR backlight interface (only SDR for now)

So-recently a bunch of laptops on the market have started using DPCD
backlight controls instead of the traditional DDI backlight controls.
Originally we thought we had this handled by adding VESA backlight
control support to i915, but the story ended up being a lot more
complicated then that.

Simply put-there's two main backlight interfaces Intel can see in the
wild. Intel's proprietary HDR backlight interface, and the standard VESA
backlight interface. Note that many panels have been observed to report
support for both backlight interfaces, but testing has shown far more
panels work with the Intel HDR backlight interface at the moment.
Additionally, the VBT appears to be capable of reporting support for the
VESA backlight interface but not the Intel HDR interface which needs to
be probed by setting the right magic OUI.

On top of that however, there's also actually two different variants of
the Intel HDR backlight interface. The first uses the AUX channel for
controlling the brightness of the screen in both SDR and HDR mode, and
the second only uses the AUX channel for setting the brightness level in
HDR mode - relying on PWM for setting the brightness level in SDR mode.

For the time being we've been using EDIDs to maintain a list of quirks
for panels that safely do support the VESA backlight interface. Adding
support for Intel's HDR backlight interface in addition however, should
finally allow us to auto-detect eDP backlight controls properly so long
as we probe like so:

* If the panel's VBT reports VESA backlight support, assume it really
does support it
* If the panel's VBT reports DDI backlight controls:
* First probe for Intel's HDR backlight interface
* If that fails, probe for VESA's backlight interface
* If that fails, assume no DPCD backlight control
* If the panel's VBT reports any other backlight type: just assume it
doesn't have DPCD backlight controls

Changes since v4:
* Fix checkpatch issues
Changes since v3:
* Stop using drm_device and use drm_i915_private instead
* Don't forget to return from intel_dp_aux_hdr_get_backlight() if we fail
to read the current backlight mode from the DPCD
* s/uint8_t/u8/
* Remove unneeded parenthesis in intel_dp_aux_hdr_enable_backlight()
* Use drm_dbg_kms() in intel_dp_aux_init_backlight_funcs()

Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210114221709.2261452-4-lyude@redhat.com

drm/i915: Keep track of pwm-related backlight hooks separately

Currently, every different type of backlight hook that i915 supports is
pretty straight forward - you have a backlight, probably through PWM
(but maybe DPCD), with a single set of platform-specific hooks that are
used for controlling it.

HDR backlights, in particular VESA and Intel's HDR backlight
implementations, can end up being more complicated. With Intel's
proprietary interface, HDR backlight controls always run through the
DPCD. When the backlight is in SDR backlight mode however, the driver
may need to bypass the TCON and control the backlight directly through
PWM.

So, in order to support this we'll need to split our backlight callbacks
into two groups: a set of high-level backlight control callbacks in
intel_panel, and an additional set of pwm-specific backlight control
callbacks. This also implies a functional changes for how these
callbacks are used:

* We now keep track of two separate backlight level ranges, one for the
high-level backlight, and one for the pwm backlight range
* We also keep track of backlight enablement and PWM backlight
enablement separately
* Since the currently set backlight level might not be the same as the
currently programmed PWM backlight level, we stop setting
panel->backlight.level with the currently programmed PWM backlight
level in panel->backlight.pwm_funcs->setup(). Instead, we rely
on the higher level backlight control functions to retrieve the
current PWM backlight level (in this case, intel_pwm_get_backlight()).
Note that there are still a few PWM backlight setup callbacks that
do actually need to retrieve the current PWM backlight level, although
we no longer save this value in panel->backlight.level like before.

Additionally, we drop the call to lpt_get_backlight() in
lpt_setup_backlight(), and avoid unconditionally writing the PWM value that
we get from it and only write it back if we're in CPU mode, and switching
to PCH mode. The reason for this is because in the original codepath for
this, it was expected that the intel_panel_bl_funcs->setup() hook would be
responsible for fetching the initial backlight level. On lpt systems, the
only time we could ever be in PCH backlight mode is during the initial
driver load - meaning that outside of the setup() hook, lpt_get_backlight()
will always be the callback used for retrieving the current backlight
level. After this patch we still need to fetch and write-back the PCH
backlight value if we're switching from CPU mode to PCH, but because
intel_pwm_setup_backlight() will retrieve the backlight level after setup()
using the get() hook, which always ends up being lpt_get_backlight(). Thus
- an additional call to lpt_get_backlight() in lpt_setup_backlight() is
made redundant.

v9:
* Drop the intel_panel_invert_pwm_level() call in lpt_setup_backlight()
* Remove leftover detritus from lpt_setup_backlight()
v8:
* Go back to getting initial brightness level with
intel_pwm_get_backlight(), the other fix we had was definitely wrong.
v7:
* Use panel->backlight.pwm_funcs->get() to get the backlight level in
intel_pwm_setup_backlight(), lest we upset lockdep
* Rebase
* Rename intel_panel_sanitize_pwm_level() to intel_panel_invert_pwm_level()
v6:
* Make sure to grab connection_mutex before calling
intel_pwm_get_backlight() in intel_pwm_setup_backlight()
v5:
* Fix indenting warnings from checkpatch
v4:
* Fix commit message
* Remove outdated comment in intel_panel.c
* Rename pwm_(min|max) to pwm_level_(min|max)
* Use intel_pwm_get_backlight() in intel_pwm_setup_backlight() instead of
indirection
* Don't move intel_dp_aux_init_bcklight_funcs() call to bottom of
intel_panel_init_backlight_funcs() quite yet
v3:
* Reuse intel_panel_bl_funcs() for pwm_funcs
* Explain why we drop lpt_get_backlight()

Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210114221709.2261452-3-lyude@redhat.com

drm/i915: Pass port to intel_panel_bl_funcs.get()

In the next commit where we split PWM related backlight functions from
higher-level backlight functions, we'll want to be able to retrieve the
backlight level for the current display panel from the
intel_panel_bl_funcs->setup() function using pwm_funcs->get(). Since
intel_panel_bl_funcs->setup() is called before we've fully read in the
current hardware state into our atomic state, we can't grab atomic
modesetting locks safely anyway in intel_panel_bl_funcs->setup(), and some
PWM backlight functions (vlv_get_backlight() in particular) require knowing
the currently used pipe we need to be able to discern the current display
pipe through other means. Luckily, we're already passing the current
display pipe to intel_panel_bl_funcs->setup() so all we have to do in order
to achieve this is pass down that parameter to intel_panel_bl_funcs->get().

So, fix this by accepting an additional pipe parameter in
intel_panel_bl_funcs->get(), and leave figuring out the current display
pipe up to the caller.

Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210114221709.2261452-2-lyude@redhat.com

drm/i915/backlight: fix CPU mode backlight takeover on LPT

The pch_get_backlight(), lpt_get_backlight(), and lpt_set_backlight()
functions operate directly on the hardware registers. If inverting the
value is needed, using intel_panel_compute_brightness(), it should only
be done in the interface between hardware registers and
panel->backlight.level.

The CPU mode takeover code added in commit 5b1ec9ac7ab5
("drm/i915/backlight: Fix backlight takeover on LPT, v3.") reads the
hardware register and converts to panel->backlight.level correctly,
however the value written back should remain in the hardware register
"domain".

This hasn't been an issue, because GM45 machines are the only known
users of i915.invert_brightness and the brightness invert quirk, and
without one of them no conversion is made. It's likely nobody's ever hit
the problem.

Fixes: 5b1ec9ac7ab5 ("drm/i915/backlight: Fix backlight takeover on LPT, v3.")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v5.1+
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108152841.6944-1-jani.nikula@intel.com

drm/i915: Pass down brightness values to enable/disable backlight callbacks

Instead of using intel_panel->backlight.level, have the caller provide us
with the current panel backlight value. We'll need this for when we
separate PWM-related backlight callbacks from other means of backlight
control (like DPCD backlight controls), as the caller of each PWM callback
will be responsible for converting the current brightness value to it's
respective PWM level.

Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204223603.249878-4-lyude@redhat.com

drm/i915: Rename pwm_* backlight callbacks to ext_pwm_*

Since we're going to need to add a set of lower-level PWM backlight
control hooks to be shared by normal backlight controls and HDR
backlight controls in SDR mode, let's add a prefix to the external PWM
backlight functions so that the difference between them and the high
level PWM-only backlight functions is a bit more obvious.

This introduces no functional changes.

Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Cc: thaytan@noraisin.net
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204223603.249878-3-lyude@redhat.com

drm/i915: refactor panel backlight control functions. (v2)

This moves the functions into static const instead of having
funcs and data in the same struct.

It leaves the power callback alone, as it is used in a different
manner.

v2: leave power callback alone (Jani)

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130210945.31850-1-airlied@gmail.com

drm/i915/backlight: fix CPU mode backlight takeover on LPT

The pch_get_backlight(), lpt_get_backlight(), and lpt_set_backlight()
functions operate directly on the hardware registers. If inverting the
value is needed, using intel_panel_compute_brightness(), it should only
be done in the interface between hardware registers and
panel->backlight.level.

The CPU mode takeover code added in commit 5b1ec9ac7ab5
("drm/i915/backlight: Fix backlight takeover on LPT, v3.") reads the
hardware register and converts to panel->backlight.level correctly,
however the value written back should remain in the hardware register
"domain".

This hasn't been an issue, because GM45 machines are the only known
users of i915.invert_brightness and the brightness invert quirk, and
without one of them no conversion is made. It's likely nobody's ever hit
the problem.

Fixes: 5b1ec9ac7ab5 ("drm/i915/backlight: Fix backlight takeover on LPT, v3.")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v5.1+
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108152841.6944-1-jani.nikula@intel.com
(cherry picked from commit 0d4ced1c5bfe649196877d90442d4fd618e19153)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Reduce INTEL_DISPLAY_ENABLED to just treat outputs as disconnected

Since the display hardware is all there even when INTEL_DISPLAY_ENABLED
return false we have to be capable of shutting it down cleanly so
as to not anger the hw. To that end let's reduce the effect of
!INTEL_DISPLAY_ENABLE to just treating all outputs as disconnected.
Should prevent anyone from automagically enabling any of them, while
still allowing us to cleanly shut them down.

v2: Put the check into the right place for CRT

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910164256.25983-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: panel: Use atomic PWM API for devs with an external PWM controller

Now that the PWM drivers which we use have been converted to the atomic
PWM API, we can move the i915 panel code over to using the atomic PWM API.

The removes a long standing FIXME and this removes a flicker where
the backlight brightness would jump to 100% when i915 loads even if
using the fastset path.

Note that this commit also simplifies pwm_disable_backlight(), by dropping
the intel_panel_actually_set_backlight(..., 0) call. This call sets the
PWM to 0% duty-cycle. I believe that this call was only present as a
workaround for a bug in the pwm-crc.c driver where it failed to clear the
PWM_OUTPUT_ENABLE bit. This is fixed by an earlier patch in this series.

After the dropping of this workaround, the usleep call, which seems
unnecessary to begin with, has no useful effect anymore, so drop that too.

Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-18-hdegoede@redhat.com

drm/i915: panel: Honor the VBT PWM min setting for devs with an external PWM controller

So far for devices using an external PWM controller (devices using
pwm_setup_backlight()), we have been hardcoding the minimum allowed
PWM level to 0. But several of these devices specify a non 0 minimum
setting in their VBT.

Change pwm_setup_backlight() to use get_backlight_min_vbt() to get
the minimum level.

Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-17-hdegoede@redhat.com

drm/i915: panel: Honor the VBT PWM frequency for devs with an external PWM controller

So far for devices using an external PWM controller (devices using
pwm_setup_backlight()), we have been hardcoding the period-time passed to
pwm_config() to 21333 ns.

I suspect this was done because many VBTs set the PWM frequency to 200
which corresponds to a period-time of 5000000 ns, which greatly exceeds
the PWM_MAX_PERIOD_NS define in the Crystal Cove PMIC PWM driver, which
used to be 21333.

This PWM_MAX_PERIOD_NS define was actually based on a bug in the PWM
driver where its period and duty-cycle times where off by a factor of 256.

Due to this bug the hardcoded CRC_PMIC_PWM_PERIOD_NS value of 21333 would
result in the PWM driver using its divider of 128, which would result in
a PWM output frequency of 6000000 Hz / 256 / 128 = 183 Hz. So actually
pretty close to the default VBT value of 200 Hz.

Now that this bug in the pwm-crc driver is fixed, we can actually use
the VBT defined frequency.

This is important because:

a) With the pwm-crc driver fixed it will now translate the hardcoded
CRC_PMIC_PWM_PERIOD_NS value of 21333 ns / 46 Khz to a PWM output
frequency of 23 KHz (the max it can do).

b) The pwm-lpss driver used on many models has always honored the
21333 ns / 46 Khz request

Some panels do not like such high output frequencies. E.g. on a Terra
Pad 1061 tablet, using the LPSS PWM controller, the backlight would go
from off to max, when changing the sysfs backlight brightness value from
90-100%, anything under aprox. 90% would turn the backlight fully off.

Honoring the VBT specified PWM frequency will also hopefully fix the
various bug reports which we have received about users perceiving the
backlight to flicker after a suspend/resume cycle.

Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-16-hdegoede@redhat.com

drm/i915: panel: Add get_vbt_pwm_freq() helper

Factor the code which checks and drm_dbg_kms-s the VBT PWM frequency
out of get_backlight_max_vbt().

This is a preparation patch for honering the VBT PWM frequency for
devices which use an external PWM controller (devices using
pwm_setup_backlight()).

Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-15-hdegoede@redhat.com

treewide: Use fallthrough pseudo-keyword

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>

drm/i915/params: switch to device specific parameters

Start using device specific parameters instead of module parameters for
most things. The module parameters become the immutable initial values
for i915 parameters. The device specific parameters in i915->params
start life as a copy of i915_modparams. Any later changes are only
reflected in the debugfs.

The stragglers are:

* i915.force_probe and i915.modeset. Needed before dev_priv is
available. This is fine because the parameters are read-only and never
modified.

* i915.verbose_state_checks. Passing dev_priv to I915_STATE_WARN and
I915_STATE_WARN_ON would result in massive and ugly churn. This is
handled by not exposing the parameter via debugfs, and leaving the
parameter writable in sysfs. This may be fixed up in follow-up work.

* i915.inject_probe_failure. Only makes sense in terms of the module,
not the device. This is handled by not exposing the parameter via
debugfs.

v2: Fix uc i915 lookup code (Michał Winiarski)

Cc: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Cc: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200618150402.14022-1-jani.nikula@intel.com

drm/i915: Use 64-bit division macro

Since the PWM framework is switching struct pwm_state.duty_cycle's
datatype to u64, prepare for this transition by using DIV_ROUND_UP_ULL
to handle a 64-bit dividend.

Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>

drm/i915: avoid unused scale_user_to_hw() warning

After the function is no longer marked 'inline', there
is now a new warning pointing out that the only caller
is inside of an #ifdef:

drivers/gpu/drm/i915/display/intel_panel.c:493:12: warning: 'scale_user_to_hw' defined but not used [-Wunused-function]
493 | static u32 scale_user_to_hw(struct intel_connector *connector,
| ^~~~~~~~~~~~~~~~

Move the function itself into that #ifdef as well.

Fixes: 81b55ef1f47b ("drm/i915: drop a bunch of superfluous inlines")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428213106.3139170-1-arnd@arndb.de
(cherry picked from commit 794bdcf71f47b98f6e003190069d5064123067ed)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: avoid unused scale_user_to_hw() warning

After the function is no longer marked 'inline', there
is now a new warning pointing out that the only caller
is inside of an #ifdef:

drivers/gpu/drm/i915/display/intel_panel.c:493:12: warning: 'scale_user_to_hw' defined but not used [-Wunused-function]
493 | static u32 scale_user_to_hw(struct intel_connector *connector,
| ^~~~~~~~~~~~~~~~

Move the function itself into that #ifdef as well.

Fixes: 81b55ef1f47b ("drm/i915: drop a bunch of superfluous inlines")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428213106.3139170-1-arnd@arndb.de

drm/i915: Have pfit calculations return an error code

Change intel_{gmch,pch}_panel_fitting() to return a normal
error vs. success int. We'll need this later to validate that
the margin properties aren't misconfigured.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-6-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>

drm/i915: Pass connector state to pfit calculations

Pass the entire connector state to intel_{gmch,pch}_panel_fitting().
For now we just need to get at .scaling_mode but in the future we'll
want access to the margin properties as well.

v2: Deal with intel_dp_ycbcr420_config()

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-5-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>

drm/i915: s/pipe_config/crtc_state/ in pfit functions

Follow the new naming convention and call the crtc state
"crtc_state", and while at it drop the redundant crtc argument.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-4-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>

drm/i915: Use drm_rect to store the pfit window pos/size

Make things a bit more abstract by replacing the pch_pfit.pos/size
raw register values with a drm_rect. Makes it slighly more convenient
to eg. compute the scaling factors.

v2: Use drm_rect_init()

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-3-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>

drm/i915: drop a bunch of superfluous inlines

Remove a number of inlines from .c files, and let the compiler decide
what's best. There's more to do, but need to start somewhere, and need
to start setting the example.

Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200420140438.14672-2-jani.nikula@intel.com

drm/i915/panel: use struct drm_device based logging

Convert all the DRM_* logging macros to the struct drm_device based
macros to provide device specific logging.

No functional changes.

Generated using the following semantic patch, originally written by
Wambui Karuga <wambui.karugax@gmail.com>, with manual fixups on top:

@@
identifier fn, T;
@@

fn(...,struct drm_i915_private *T,...) {
<+...
(
-DRM_INFO(
+drm_info(&T->drm,
...)
|
-DRM_NOTE(
+drm_notice(&T->drm,
...)
|
-DRM_ERROR(
+drm_err(&T->drm,
...)
|
-DRM_WARN(
+drm_warn(&T->drm,
...)
|
-DRM_DEBUG_DRIVER(
+drm_dbg(&T->drm,
...)
|
-DRM_DEBUG_KMS(
+drm_dbg_kms(&T->drm,
...)
|
-DRM_DEBUG_ATOMIC(
+drm_dbg_atomic(&T->drm,
...)
)
...+>
}

@@
identifier fn, T;
@@

fn(...) {
...
struct drm_i915_private *T = ...;
<+...
(
-DRM_INFO(
+drm_info(&T->drm,
...)
|
-DRM_NOTE(
+drm_notice(&T->drm,
...)
|
-DRM_ERROR(
+drm_err(&T->drm,
...)
|
-DRM_WARN(
+drm_warn(&T->drm,
...)
|
-DRM_DEBUG_DRIVER(
+drm_dbg(&T->drm,
...)
|
-DRM_DEBUG_KMS(
+drm_dbg_kms(&T->drm,
...)
|
-DRM_DEBUG_ATOMIC(
+drm_dbg_atomic(&T->drm,
...)
)
...+>
}

Cc: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200402114819.17232-2-jani.nikula@intel.com

drm/i915: Pass atomic state to encoder hooks

We're going to want access to the atomic state for iterating
the slave crtcs when enabling the port sync master crtc. Pass
the atomic state all the way down.

The alternative would be yet another encoder hook which we'll
have to call after all the normal modeset stuff is done. Not
really a fan of yet another hook just for this.

Note that during readout state sanitation we are now going
to pass NULL as the atomic state since we don't have one.
We need to change that and then we can also s/crtc_state/crtc/
and s/conn_state/conn/ for the encoder hooks as well.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-13-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: panel: Use intel_panel_compute_brightness() from pwm_setup_backlight()

Use intel_panel_compute_brightness() from pwm_setup_backlight() so that
we correctly take i915_modparams.invert_brightness and/or
QUIRK_INVERT_BRIGHTNESS into account when setting + getting the initial
brightness value.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221172927.510027-1-hdegoede@redhat.com

drm/i915: Parametrize PFIT_PIPE

Make the PFIT_PIPE stuff less ugly via parametrization.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200212161738.28141-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Read rawclk_freq earlier

Read the rawclk_freq during runtime info probing, prior to its first use
in computing the CS timestamp frequency. Then store it in the runtime
info, and include it in the debug printouts.

Closes: https://gitlab.freedesktop.org/drm/intel/issues/834
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200216163445.555786-1-chris@chris-wilson.co.uk

drm/i915/panel: automatic conversion to drm_device based logging macros.

Converts various instances of the printk based drm logging macros to the
struct drm_device based logging macros in i915/display/intel_panel.c
using the following coccinelle script that transforms based on the
existence of a struct drm_i915_private device pointer:
@@
identifier fn, T;
@@

fn(...) {
...
struct drm_i915_private *T = ...;
<+...
(
-DRM_INFO(
+drm_info(&T->drm,
...)
|
-DRM_ERROR(
+drm_err(&T->drm,
...)
|
-DRM_WARN(
+drm_warn(&T->drm,
...)
|
-DRM_DEBUG(
+drm_dbg(&T->drm,
...)
|
-DRM_DEBUG_KMS(
+drm_dbg_kms(&T->drm,
...)
|
-DRM_DEBUG_DRIVER(
+drm_dbg(&T->drm,
...)
|
-DRM_DEBUG_ATOMIC(
+drm_dbg_atomic(&T->drm,
...)
)
...+>
}

@@
identifier fn, T;
@@

fn(...,struct drm_i915_private *T,...) {
<+...
(
-DRM_INFO(
+drm_info(&T->drm,
...)
|
-DRM_ERROR(
+drm_err(&T->drm,
...)
|
-DRM_WARN(
+drm_warn(&T->drm,
...)
|
-DRM_DEBUG(
+drm_dbg(&T->drm,
...)
|
-DRM_DEBUG_DRIVER(
+drm_dbg(&T->drm,
...)
|
-DRM_DEBUG_KMS(
+drm_dbg_kms(&T->drm,
...)
|
-DRM_DEBUG_ATOMIC(
+drm_dbg_atomic(&T->drm,
...)
)
...+>
}

Checkpatch warnings were addressed manually.

Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200130083229.12889-13-wambui.karugax@gmail.com

drm/i915/display/panel: Make WARN* drm specific where drm_priv ptr is available

drm specific WARN* calls include device information in the
backtrace, so we know what device the warnings originate from.

Covert all the calls of WARN* with device specific drm_WARN*
variants in functions where drm_i915_private struct pointer is readily
available.

The conversion was done automatically with below coccinelle semantic
patch.

@rule1@
identifier func, T;
@@
func(...) {
...
struct drm_i915_private *T = ...;
<+...
(
-WARN(
+drm_WARN(&T->drm,
...)
|
-WARN_ON(
+drm_WARN_ON(&T->drm,
...)
|
-WARN_ONCE(
+drm_WARN_ONCE(&T->drm,
...)
|
-WARN_ON_ONCE(
+drm_WARN_ON_ONCE(&T->drm,
...)
)
...+>
}

@rule2@
identifier func, T;
@@
func(struct drm_i915_private *T,...) {
<+...
(
-WARN(
+drm_WARN(&T->drm,
...)
|
-WARN_ON(
+drm_WARN_ON(&T->drm,
...)
|
-WARN_ONCE(
+drm_WARN_ONCE(&T->drm,
...)
|
-WARN_ON_ONCE(
+drm_WARN_ON_ONCE(&T->drm,
...)
)
...+>
}

Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128181603.27767-16-pankaj.laxminarayan.bharadiya@intel.com

drm/i915/panel: use intel_de_*() functions for register access

The implicit "dev_priv" local variable use has been a long-standing pain
point in the register access macros I915_READ(), I915_WRITE(),
POSTING_READ(), I915_READ_FW(), and I915_WRITE_FW().

Replace them with the corresponding new display engine register
accessors intel_de_read(), intel_de_write(), intel_de_posting_read(),
intel_de_read_fw(), and intel_de_write_fw().

No functional changes.

Generated using the following semantic patch:

@@
expression REG, OFFSET;
@@
- I915_READ(REG)
+ intel_de_read(dev_priv, REG)

@@
expression REG, OFFSET;
@@
- POSTING_READ(REG)
+ intel_de_posting_read(dev_priv, REG)

@@
expression REG, OFFSET;
@@
- I915_WRITE(REG, OFFSET)
+ intel_de_write(dev_priv, REG, OFFSET)

@@
expression REG;
@@
- I915_READ_FW(REG)
+ intel_de_read_fw(dev_priv, REG)

@@
expression REG, OFFSET;
@@
- I915_WRITE_FW(REG, OFFSET)
+ intel_de_write_fw(dev_priv, REG, OFFSET)

Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/efd117ff0a63ef6ec1a4514f2ee133ca33b3f0a0.1579871655.git.jani.nikula@intel.com

drm/i915: DSI: select correct PWM controller to use based on the VBT

At least Bay Trail (BYT) and Cherry Trail (CHT) devices can use 1 of 2
different PWM controllers for controlling the LCD's backlight brightness.
Either the one integrated into the PMIC or the one integrated into the
SoC (the 1st LPSS PWM controller).

So far in the LPSS code on BYT we have skipped registering the LPSS PWM
controller "pwm_backlight" lookup entry when a Crystal Cove PMIC is
present, assuming that in this case the PMIC PWM controller will be used.

On CHT we have been relying on only 1 of the 2 PWM controllers being
enabled in the DSDT at the same time; and always registered the lookup.

So far this has been working, but the correct way to determine which PWM
controller needs to be used is by checking a bit in the VBT table and
recently I've learned about 2 different BYT devices:
Point of View MOBII TAB-P800W
Acer Switch 10 SW5-012

Which use a Crystal Cove PMIC, yet the LCD is connected to the SoC/LPSS
PWM controller (and the VBT correctly indicates this), so here our old
heuristics fail.

This commit fixes using the wrong PWM controller on these devices by
calling pwm_get() for the right PWM controller based on the
VBT dsi.config.pwm_blc bit.

Note this is part of a series which contains 2 other patches which renames
the PWM lookup for the 1st SoC/LPSS PWM from "pwm_backlight" to
"pwm_pmic_backlight" and the PWM lookup for the Crystal Cove PMIC PWM
from "pwm_backlight" to "pwm_pmic_backlight".

Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216202906.1662893-4-hdegoede@redhat.com

drm/i915: Perform automated conversions for crtc uapi/hw split, base -> uapi.

Split up crtc_state->base to uapi. This is done using the following patch,
ran after the previous commit that splits out any hw references:

@@
struct intel_crtc_state *T;
@@
-T->base
+T->uapi

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-5-maarten.lankhorst@linux.intel.com

drm/i915: Perform automated conversions for crtc uapi/hw split, base -> hw.

Split up crtc_state->base to hw where appropriate. This is done using the following patch:

@@
struct intel_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-T->base.x
+T->hw.x

@@
struct drm_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-to_intel_crtc_state(T)->base.x
+to_intel_crtc_state(T)->hw.x

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-4-maarten.lankhorst@linux.intel.com

drm/i915: rename intel_drv.h to display/intel_display_types.h

Everything about the file is about display, and mostly about types
related to display. Move under display/ as intel_display_types.h to
reflect the facts.

There's still plenty to clean up, but start off with moving the file
where it logically belongs and naming according to contents.

v2: fix the include guard name in the renamed file

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190806113933.11799-1-jani.nikula@intel.com

drm/i915: move modesetting output/encoder code under display/

Add a new subdirectory for display code, and start off by moving
modesetting output/encoder code. Judging by the include changes, this is
a surprisingly clean operation.

v2:
- move intel_sdvo_regs.h too
- use tabs for Makefile file lists and sort them

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190613084416.6794-2-jani.nikula@intel.com