drm/i915/dp: Fix connector DSC HW state readout

The DSC HW state of DP connectors is read out during driver loading and
system resume in intel_modeset_update_connector_atomic_state(). This
function is called for all connectors though and so the state of DSI
connectors will also get updated incorrectly, triggering a WARN there
wrt. the DSC decompression AUX device.

Fix the above by moving the DSC state readout to a new DP connector
specific sync_state() hook. This is anyway the logical place to update
the connector object's state vs. the connector's atomic state.

Fixes: b2608c6b3212 ("drm/i915/dp_mst: Enable MST DSC decompression for all streams")
Reported-and-tested-by: Drew Davenport <ddavenport@chromium.org>
Closes: https://lore.kernel.org/all/Zb0q8IDVXS0HxJyj@chromium.org
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240205132631.1588577-1-imre.deak@intel.com
(cherry picked from commit a62e145981500996ea76af3d740ce0c0d74c5be0)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915/dp_mst: Enable MST DSC decompression for all streams

Enable DSC decompression for all streams. In particular atm if a sink is
connected to a last branch device that is downstream of the first branch
device connected to the source, decompression is not enabled for it.
Similarly it's not enabled if the sink supports this with the last
branch device passing through the compressed stream to it.

Enable DSC in the above cases as well. Since last branch devices may
handle the decompression for multiple ports, toggling DSC needs to be
refcounted, add this using the DSC AUX device as a reference.

v2:
- Fix refcounting, setting/clearing
connector->dp.dsc_decompression_enabled always as needed. (Stan)
- Make the refcounting more uniform for the SST vs. MST case.
- Add state checks for connector->dp.dsc_decompression_enabled and
connector crtc.
- Sanitize connector DSC decompression state during HW setup.
- s/use_count/ref_count/
v3:
- Remove stale TODO: comment to set the actual decompression_aux.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231107001505.3370108-6-imre.deak@intel.com

drm/i915/mtl: Add support for PM DEMAND

MTL introduces a new way to instruct the PUnit with
power and bandwidth requirements of DE. Add the functionality
to program the registers and handle waits using interrupts.
The current wait time for timeouts is programmed for 10 msecs to
factor in the worst case scenarios. Changes made to use REG_BIT
for a register that we touched(GEN8_DE_MISC_IER _MMIO).

Wa_14016740474 is added which applies to Xe_LPD+ display

v2: checkpatch warning fixes, simplify program pmdemand part

v3: update to dbufs and pipes values to pmdemand register(stan)
Removed the macro usage in update_pmdemand_values()

v4: move the pmdemand_pre_plane_update before cdclk update
pmdemand_needs_update included cdclk params comparisons
pmdemand_state NULL check (Gustavo)
pmdemand.o in sorted order in the makefile (Jani)
update pmdemand misc irq handler loop (Gustavo)
active phys bitmask and programming correction (Gustavo)

v5: simplify pmdemand_state structure
simplify methods to find active phys and max port clock
Timeout in case of previou pmdemand task pending (Gustavo)

v6: rebasing
updates to max_ddiclk calculations (Gustavo)
updates to active_phys count method (Gustavo)

v7: use two separate loop to iterate throug old and new
crtc states to calculate the active phys (Gustavo)

v8: use uniform function names (Gustavo)

v9: For phys change iterate through connectors (Imre)
Look for change in phys for pmdemand update (Gustavo, Imre)
Some more stlying changes (Imre)
Update pmdemand state during HW readout/sanitize (Imre)

v10: Fix CI checkpatch warnings

v11: use correct pmdemand object pointer during hw readout,
simplify the check for phys need update (Gustavo)

v12: Handle possible non serialize cases (Imre)
Initialise also pmdemand params HW readout (Imre)
Update active phys mask during sanitize calls (Imre)
Check TC/encoder changes to limit connector update (Imre)

v13: Check display version before accessing pmdemand functions

v14: Move is_serialized to intel_global_state.c
simplify update params and other stlying issues (Imre)

Bspec: 66451, 64636, 64602, 64603
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v4
Acked-by: Gustavo Sousa <gustavo.sousa@intel.com> #v11
Reviewed-by: Imre Deak <imre.deak@intel.com>
[RK: Fixed minor typo in one of the comments. s/qclck_gc/qclk_gv/]
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606201032.347449-1-vinod.govindapillai@intel.com

drm/i915/tc: Reset TypeC PHYs left enabled in DP-alt mode after the sink disconnects

If the output on a DP-alt link with its sink disconnected is kept
enabled for too long (about 20 sec), then some IOM/TCSS firmware timeout
will cause havoc on the PCI bus, at least for other GFX devices on it
which will stop powering up. Since user space is not guaranteed to do a
disabling modeset in time, switch such disconnected but active links to
TBT mode - which is without such shortcomings - with a 2 second delay.

If the above condition is detected already during the driver load/system
resume sanitization step disable the output instead, as at that point no
user space or kernel client depends on a consistent output state yet and
because subsequent atomic modeset on such connectors - without the
actual sink capabilities available - can fail.

An active/disconnected port as above will also block the HPD status of
other active/disconnected ports to get updated (stuck in the connected
state), until the former port is disabled, its PHY is disconnected and
a ~10 ms delay has elapsed. This means the link state for all TypeC
ports/CRTCs must be rechecked after a CRTC is disabled due to the above
reason. For this disconnect the PHY synchronously after the CRTC/port is
disabled and recheck all CRTCs for the above condition whenever such a
port is disabled.

To account for a race condition during driver loading where the sink is
disconnected after the above sanitization step and before the HPD
interrupts get enabled, do an explicit check/link reset if needed from
the encoder's late_register hook, which is called after the HPD
interrupts are enabled already.

v2:
- Handle an active/disconnected port blocking the HPD state update of
another active/disconnected port.
- Cancel the delayed work resetting the link also from the encoder
enable/suspend/shutdown hooks.
- Rebase on the earlier intel_modeset_lock_ctx_retry() addition,
fixing here the missed atomic state reset in case of a retry.
- Fix handling of an error return from intel_atomic_get_crtc_state().
- Recheck if the port needs to be reset after all the atomic state
is locked and async commits are waited on.

v3:
- Add intel_crtc_needs_link_reset(), instead of open-coding it,
keep intel_crtc_has_encoders(). (Ville)
- Fix state dumping and use a bitmask to track disabled CRTCs in
intel_sanitize_all_crtcs(). (Ville)
- Set internal in intel_atomic_state right after allocating it.
(Ville)
- Recheck all CRTCs (not yet force-disabled) after a CRTC is
force-disabled for any reason (not only due to a link state)
in intel_sanitize_all_crtcs().
- Reduce delay after CRTC disabling to 20ms, and use the simpler
msleep().
- Clarify code comment about HPD behaviour in
intel_sanitize_all_crtcs().
- Move all the TC link reset logic to intel_tc.c .
- Cancel the link reset work synchronously during system suspend,
driver unload and shutdown.

v4:
- Rebased on previous patch, which allows calling the TC port
suspend/cleanup handlers without modeset locks held; remove the
display driver suspended assert from the link reset work
accordingly.

v5: (Ville)
- Remove reset work canceling from intel_ddi_pre_pll_enable().
- Track a crtc vs. pipe mask in intel_sanitize_all_crtcs().
- Add reset_link_commit() to clarify the
intel_modeset_lock_ctx_retry loop.

Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5860
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512195513.2699-2-imre.deak@intel.com

drm/i915: Add support for disabling any CRTCs during HW readout/sanitization

During HW readout/sanitization CRTCs can be disabled only if they don't
have an attached encoder (and so the encoder disable hooks don't need to
be called). An upcoming patch will need to disable CRTCs also with an
attached encoder, so add support for this.

For bigjoiner configs the encoder disabling hooks require the slave CRTC
states, so add these too to the atomic state. Since the connector atomic
state is already up-to-date when the CRTC is disabled the connector
state needs to be updated (reset) after the CRTC is disabled, make this
so. Follow the proper order of disabling first all bigjoiner slaves,
then any port synced CRTC slaves followed by the CRTC originally
requested to be disabled.

v2:
- Fix calculating the bigjoiner_masters mask in a port sync config,
(Ville)
- Keep _noatomic suffix in intel_crtc_disable_noatomic(). (Ville)
- Rebase on full CRTC state reset in this patchset, not requiring
resetting the bigjoiner state separately and (instead) resetting
the full atomic CRTC and related global state after all linked
pipes got disabled.
- Disable portsync slaves before a portsync master.
- Disable a portsync master if a linked portsync slave is disabled.

v3: (Ville)
- Use s/u32/u8 for transcoder and pipe masks.
- Use is_power_of_2() instead of hweight()==1.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-8-imre.deak@intel.com

drm/i915: Factor out set_encoder_for_connector()

Factor out a function setting the encoder and CRTC in the connector
atomic state, required by a follow up patch.

No functional changes.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-7-imre.deak@intel.com

drm/i915: Separate intel_crtc_disable_noatomic_begin/complete()

Split calling the CRTC/encoder disabling hooks and updating the CRTC and
DPLL object states from updating the CRTC and atomic state and other
global state (BW, CDCLK, DBUF) into separate functions. When disabling a
bigjoiner configuration the latter step can be done only after all the
linked pipes are disabled, so this change prepares for that.

No functional changes.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-6-imre.deak@intel.com

drm/i915: Update connector atomic state before crtc sanitize-disabling

During HW state readout/sanitization an up-to-date connector atomic
state will be required by a follow-up patch, which can disable CRTCs
with an encoder (and calling the correct encoder hooks happens via the
connector atomic state encoder pointer). So update the connector state
already before the CRTC sanitize/disable step. For now this doesn't make
a difference, since intel_modeset_update_connector_atomic_state() will
update/enable the atomic state only for connectors that have an enabled
encoder/CRTC. Such CRTCs/encoders will not be affected by
intel_sanitize_crtc().

v2: Add comment about why the connector state needs to be up-to-date.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-5-imre.deak@intel.com

drm/i915: Make the CRTC state consistent during sanitize-disabling

Make sure that the CRTC state is reset correctly, as expected after
disabling the CRTC.

In particular this change will:
- Zero all the CSC blob pointers after intel_crtc_free_hw_state()
has freed them.
- Zero the shared DPLL and port PLL pointers and clear the
corresponding CRTC reference flag in the PLL state.
- Reset all the transcoder and pipe fields.

v2:
- Reset fully the CRTC state. (Ville)
- Clear pipe active flags in the DPLL state.

v3:
- Clear only the CRTC reference flag and add a helper for this.
(Ville)

v4:
- Rebased on previous patch, adding
intel_unreference_shared_dpll_crtc() separately. (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-4-imre.deak@intel.com

drm/i915: Flag purely internal commits to not clear crtc_state->inherited

If we have to force the hardware to go through a full modeset
due to eg. cdclk reprogramming, we need to preserve
crtc_state->inherited for all crtcs that have not otherwise
gone through the whole compute_config() stuff after connectors
have been detected.

Otherwise eg. cdclk induced modeset glk_force_audio_cdclk()
will clear the inherited flag, and thus the first real commit
coming from userspace later on will not be forced through
the full .compute_config() path and so eg. audio state may
not get properly recomputed.

But instead of adding all kinds of ad-hoc crtc_state->inherited
preservation hacks all over, let's change things so that we
only clear it for the crtcs directly included in userspace/client
initiated commits.

Should be far less fragile since now we just need to remember
to flag the internal commits, and not worry about where new
crtcs might get pulled in.

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5260
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230328122357.1697-1-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>

drm/i915/vrr: Tell intel_crtc_update_active_timings() about VRR explicitly

In order to move VRR enable/disable to a place where it's also
applicable to fastsets we need to be prepared to configure
the pipe into non-VRR mode initially, and then later switch
to VRR mode. To that end allow the active timings to be configured
in non-VRR mode temporarily even when the crtc_state says we're
going to be using VRR.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320203352.19515-5-ville.syrjala@linux.intel.com
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>

drm/i915: Move shared DPLL disabling into CRTC disable hook

The spec requires disabling the PLL on TC ports before disconnecting the
port's PHY. Prepare for that by moving the PLL disabling to the CRTC
disable hook, while disconnecting the PHY will be moved to the
post_pll_disable() encoder hook in the next patch.

v2: Move the call from intel_crtc_disable_noatomic() as well.

Reviewed-by: Mika Kahola <mika.kahola@intel.com> # v1
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-27-imre.deak@intel.com

drm/i915: Relocate intel_crtc_update_active_timings()

Move intel_crtc_update_active_timings() into intel_vblank.c
where it more properly belongs.

Also do the s/dev_priv/i915/ modernization rename while at it.

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230310235828.17439-3-ville.syrjala@linux.intel.com

drm/i915/dmc: allocate dmc structure dynamically

sizeof(struct intel_dmc) > 1024 bytes, allocated on all platforms as
part of struct drm_i915_private, whether they have DMC or not.

Allocate struct intel_dmc dynamically, and hide all the dmc details
behind an opaque pointer in intel_dmc.c.

Care must be taken to take into account all cases: DMC not supported on
the platform, DMC supported but not initialized, and DMC initialized but
not loaded. For the second case, we need to move the wakeref out of
struct intel_dmc.

v2:
- Rebase to kzalloc dmc after runtime pm get (Imre)

Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230301122944.1298929-4-jani.nikula@intel.com

drm/i915: remove unnecessary intel_pm.h includes

As intel_pm.[ch] used to contain much more, intel_pm.h was included in a
lot of places. Many of them are now unnecessary. Remove.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ab9a7147b0cd63d95b9f27ed40615b9c9be18f84.1677678803.git.jani.nikula@intel.com

drm/i915: Mark FIFO underrun disabled earlier

At least on some platforms (tested on ctg) the way
vgacon does screen blanking seems to flag constant
FIFO underruns, which means we have to be prepared
for them while the driver is loading. Currently
there is a time window between drm_crtc_init() and
intel_sanitize_fifo_underrun_reporting() during
which FIFO underrun reporting is in fact marked as
enabled. Thus we may end up mistakenly detecting
these bogus underruns during driver init.

Close the race by marking FIFO underrun reporting
as disabled prior to even registering the crtc.
intel_sanitize_fifo_underrun_reporting()/etc. will
re-enable it later if needed.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125185234.21599-2-ville.syrjala@linux.intel.com
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>

drm/i915/display/core: use intel_de_rmw if possible

The helper makes the code more compact and readable.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230105131046.2173431-1-andrzej.hajda@intel.com

drm/i915/wm: add .get_hw_state to watermark funcs

Get rid of the if ladder in intel_modeset_setup_hw_state() and hide a
number of functions by adding a .get_hw_state() hook to watermark
functions. At least for now, combine the platform specific sanitization
to the hw state readouts on the relevant platforms instead of adding a
separate hook for that.

There's a functional change on PCH split platforms: If i9xx_wm_init()
fails to read plane latency and chooses the nop functions,
ilk_wm_get_hw_state() won't get called for readout. Add the
ilk_init_lp_watermarks() call on that path which now won't be called in
.get_hw_state(), as it looks like the only thing that could make a
difference.

v2:
- Add missing static (kernel test robot)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6da32831e40606cc8b90491b83196917f2ce36ab.1676317696.git.jani.nikula@intel.com

drm/i915/wm: move remaining watermark code out of intel_pm.c

Add new files intel_wm.[ch] and i9xx_wm.[ch] under display/ to hold
generic and pre-SKL watermark code, respectively. SKL+ watermark code
has already been split out to skl_watermark.[ch].

Use the _wm.[ch] naming for brevity; we may want to rename
skl_watermark.[ch] later accordingly.

Add new intel_wm_init() to call either skl_wm_init() or
i9xx_wm_init(i915) depending on the platform, the latter comprising of
the remains of intel_init_pm().

Sprinkle in some minor checkpatch fixes while moving the code.

v2:
- Rebase
- Fix copyright year

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ddf04a07a37f0368b3fef85d4ebb924082fec6cd.1676317696.git.jani.nikula@intel.com

drm/i915: Enable a PIPEDMC whenever its corresponding pipe is enabled

Make sure that PIPEDMCs are enabled whenever the corresponding pipe is
enabled.

This is required at least by the latest ADLP v2.18 firmware, which adds
a new handler enabled by default and running whenever the pipe is
enabled at the vertical referesh rate.

Bspec: 50344, 67620

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230102183324.862279-1-imre.deak@intel.com

drm/i915: stop including i915_irq.h from i915_trace.h

Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.

Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.

Also some places actually needed i915_irq.h too.

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com

drm/i915: Introduce crtc_state->{pre,post}_csc_lut

Add an extra remapping step between the logical state of the LUTs
(hw.(de)gamma_lut) as specified via uapi/bigjoiner copy vs.
the actual state of the LUTs programmed into the hardware.

With this we should be finally able finish the (de)gamma
readout/state checker support for the remaining platforms
(ilk-skl) where the same hardware LUT can be positioned
either before or after the pipe CSC unit. Where we position
it depends on factors such as presence of the logical degamma
LUT, RGB vs. YCbCr output, full vs. limited RGB quantization
range.

Without the extra remapping step the state readout doesn't
really know whether the LUT read from the hardware is the
degamma or gamma LUT, and so we is unable to accurately store
it into our crtc state. With the remapping step we know
exactly where to put it given the order of the LUT vs. CSC
in the hardware state.

Only the initial hw->uapi state readout done during driver
load/resume still has the problem of not really knowing
what to do with the LUT(s). But we can just assume 1:1
mapping there and let subsequent commits fix things up.

Another benefit is that we now have a place for purely
internal LUTs, without complicating the bigjoiner uapi->hw
copy logic. This should prove useful for streamlining
glk degamma LUT handling.

Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221024161514.5340-3-ville.syrjala@linux.intel.com

drm/i915: Remove one use macro

Remove one use macro for_each_connector_on_encoder which
is only being used at intel_encoder_find_connector.

Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221020104635.874860-2-suraj.kandpal@intel.com

drm/i915: Extract skl_watermark.c

Pull all the skl+ watermark code (and the dbuf/sagv/ipc code
since it's all sort of intertwined and I'm too lazy to think
of a finer grained split right now) into its own file from the
catch-all intel_pm.c.

Also sneak in the s/dev_priv/i915/ rename while at it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908191646.20239-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: move dbuf under display sub-struct

Move display dbuf related members under drm_i915_private display
sub-struct.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3363a516c12bd8bfb240131e9eb9fc3a0f3057a3.1661779055.git.jani.nikula@intel.com

drm/i915: move and group cdclk under display.cdclk

Move display cdclk related members under drm_i915_private display
sub-struct.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7df23655be5dc70fb1a2b43ce41e1682e40395d8.1661779055.git.jani.nikula@intel.com

drm/i915: move and group max_bw and bw_obj under display.bw

Move display bandwidth related members under drm_i915_private display
sub-struct.

v2: Rebase

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c8b9e2fdc5c226ffb71759a20e561c832a774ba5.1661779055.git.jani.nikula@intel.com

drm/i915: add display sub-struct to drm_i915_private

In another long-overdue cleanup, add a display sub-struct to
drm_i915_private, and start moving display related members there. Start
with display funcs that need a rename anyway to not collide with the new
display member.

Add a new header under display/ for defining struct intel_display.

Rename struct drm_i915_display_funcs to intel_display_funcs while at it.

v2:
- Fix multi-line comment style (Arun)
- Use display as the member name

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d44cae096b664f7015f8c797d6dfd4964226d4f8.1661346845.git.jani.nikula@intel.com

drm/i915/display: convert modeset setup to struct drm_i915_private *i915

Pass struct drm_i915_private * instead of struct drm_device *, and
rename dev_priv to i915.

v2: Rebase

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220617094817.3466584-2-jani.nikula@intel.com

drm/i915/display: split out hw state readout and sanitize

Split out the modeset hardware state readout and sanitize, or state
setup, to a separate file.

Do some drive-by checkpatch fixes while at it.

v2: Rebase

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220617094817.3466584-1-jani.nikula@intel.com