drm/amd/display: Add shared firmware state for DMUB IPS handshake

[Why]
Read modify write hazards can occur when using a single shared scratch
register between driver and firmware leading to driver accessing DCN
in IPS2 and a system hang.

[How]
Add infrastructure for using REGION6 as a shared firmware state between
driver and firmware. This region is uncachable.

Replace the existing get/set idle calls with reads/writes to the
(volatile) shared firmware state blocks that a separated by at least
a cache line between firmware and driver.

Remove the workarounds that required rewriting/checking read modify
write hazards.

Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add helpers to get DMUB FW boot options

[Why & How]
To query the bits and print them out for debug purposes.

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Cruise Hung <cruise.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Set minimum requirement for using PSR-SU on Rembrandt

A number of parade TCONs are causing system hangs when utilized with
older DMUB firmware and PSR-SU. Some changes have been introduced into
DMUB firmware to add resilience against these failures.

Don't allow running PSR-SU unless on the newer firmware.

Cc: stable@vger.kernel.org
Cc: Sean Wang <sean.ns.wang@amd.com>
Cc: Marc Rossi <Marc.Rossi@amd.com>
Cc: Hamza Mahfooz <Hamza.Mahfooz@amd.com>
Cc: Tsung-hua (Ryan) Lin <Tsung-hua.Lin@amd.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2443
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Restore rptr/wptr for DMCUB as workaround

[Why]
States may be desync after resume.

[How]
Sync sw state with hw state.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Wait DMCUB to idle state before reset.

[WHY]
Very low rate to cause memory access issue while resetting
DMCUB after the halt command was sent to it.
The process of stopping fw of DMCUB may be timeout, that means
it is not in idle state, such as the window frames may still be
kept in cache, so reset by force will cause MMHUB hang.

[HOW]
After the halt command was sent, keep checking the DMCUB state until
it is idle.

Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: hengzhou <Hengyong.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add periodic detection when zstate is enabled

[Why]
When system is in Z10 HPD interrupts cannot fire, we may miss display
configuration changes.

[How]
When Zstate is enabled, if DMUB indicate DCN has lost power, do a
complete detection periodically.

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: DMUB Outbound Interrupt Process-X86

[Why]
dmub would notify x86 response time violation by GPINT_DATAOUT

[How]
1. Use GPINT_DATAOUT to trigger x86 interrupt
2. Register GPINT_DATAOUT interrupt handler.
3. Trigger ACR while GPINT_DATAOUT occurred.

Signed-off-by: Chun-Liang Chang <Chun-Liang.Chang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Extend DMUB diagnostic logging to DCN3.1

[Why & How]
Extend existing support for DCN2.1 DMUB diagnostic logging to
DCN3.1 so we can collect useful information if the DMUB hangs.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DCN3.1 DMCUB

DMCU-B (Display Micro-Controller Unit B) is a display microcontroller
used for shared display functionality with BIOS and for advanced
power saving display features.

Extends the command header to include new DCN3.1 functionality.

Adds new interfaces to DC dmub interface as well for z-state support.

Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>