drm/amd/display: To adjust dprefclk by down spread percentage

[Why]
Panels show corruption with high refresh rate timings when ssc is
enabled.

[How]
Read down-spread percentage from lut to adjust dprefclk. Issues come
from S0i3 with this commit has been fixed by SMU.

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add function for dumping clk registers

[why]
Allow devs to check raw clk register values by dumping them on the log

[how]
Add clk register dump implementation

Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Johnson Chen <johnson.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add a check for idle power optimization

[why]
Need a helper function to check idle power is allowed
so that dc doesn't access any registers that are power-gated.

[how]
Implement helper function to check idle power optimization.
Enable a hook to check if detection is allowed.

V2:
Add function hooks for set and get idle states.
Check if function hook was properly initialized.

Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Choi <nicholas.choi@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Revert "Improve x86 and dmub ips handshake"

This reverts commit 1288d702080949f87688d49dfeeacc99f40adc9b.

Causes intermittent hangs during reboot stress testing.

Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Improve x86 and dmub ips handshake

[Why]
There is a race condition between x86 and dmcub fw when attempting to exit
IPS2. Scenarios including exiting IPS2 before IPS2 has been entered. This
can cause unexpected hang when DMCUB attempt to exit while PMFW still
tries to enter IPS2.

[How]
A new design has been introduced to remove race conditions and improve the
handshake between x86 and DMCUB. An AON scratch register is borrowed from
PMFW to determine whether DMCUB has committed to IPS entry or not.

In the case when dmcub has committed IPS entry, x86 must poll until an exit
event occurred either from DMCUB(IPS1) or PMFW(IPS2). x86 will wait
upperbound of evaluation and IPS entry time to ensure IPS2 exit event has
been sent to PMFW.

Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add IPS control flag

[why]
Currently, driver is not aware if IPS is supported. After PMFW helps
implement new message query functionality, driver will set IPS
capability flag.

[how]
Create new SMU hook function to query IPS capability. Based on the cap,
set appropriate flags to false for power-gating purposes. This will
avoid keeping SMU busy and offloading tasks to DMUB/driver.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix some non-initialized register mask and setting

[why]
fix some non-initialized register mask and update golden setting

Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DCN35 CLK_MGR

[Why & How]
Add CLK_MGR handling for DCN35.

v2: Drop stale SMU interfaces (Alex)

Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Enable dc mode clock switching for DCN32x

- DC mode clock switch interface was previously only executed
for DCN303. Enable it for DCN32x so that the interface is called
correctly
- Assign function pointers for DCN32x that are used in the dc mode
interface
- Update the dc mode interface to work generically for each ASIC
- In update_clocks, make sure to consider softmax if we're in DC mode

Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Filter out AC mode frequencies on DC mode systems

Why:
Limit maximum clock speeds to DC mode limits for DC mode systems
How:
Store DC mode limits when individual clocks are initialized and
cap the values when building the clock table

Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Austin Zheng <austin.zheng@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: On clock init, maintain DISPCLK freq

[Description]
- On init if a display is connected, we need to maintain the DISPCLK
frequency
- Even though DPG_EN=1, the display still requires the correct
timing or it could cause audio corruption (if DISPCLK freq
is reduced)
- Read the current DISPCLK freq and request the same value to ensure
the timing is valid and unchanged
- However, add option to do a full pipe power down (including link)
which will also avoid audio related issues
- Disabled for the time being on dcn32

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Acquire FCLK DPM levels on DCN32

[Why & How]
Acquire FCLK DPM levels to properly construct DML clock limits. Further
add new logic to keep number of indices for each clock in clk_mgr.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Correct dram channel width for dcn314

[Why]
The interpretation of the number of memory channels
differ by memory type, and this affects channel width
for the DML input.

[How]
Set dram channel width according to memory type for
dcn314.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Correct dram channel width for dcn314

[Why]
The interpretation of the number of memory channels
differ by memory type, and this affects channel width
for the DML input.

[How]
Set dram channel width according to memory type for
dcn314.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix __floatunsidf undefined for 32 bit compilation

When we tried to compile DCN32/321 for 32-bit architecture, we got this
error message:

ERROR: modpost: "__floatunsidf" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!

This was caused because we were trying to assign an unsigned int to a
double value which causes issues for 32-bit architecture. This issue can
be fixed by changing the value type.

Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Fixes: 265280b99822 ("drm/amd/display: add CLKMGR changes for DCN32/321")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Get VCO frequency from registers

Add support to get VCO frequency from registers.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add CLKMGR changes for DCN32/321

Add support for managing DCN3.2.x clocks.

v2: squash in smu interface updates (Alex)
v3: Drop unused SMU header (Alex)

Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: revert Blank eDP on disable/enable drv

why and how:
Revert this change. It was causing a black screen with certain blocks

Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Leung, Martin <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: update dcn315 clk table read

Clean up the sequence by making sure clk_mgr always builds a
reasonable clock table regardless of what we read from smu
by moving all defaults from resource soc struct to clk_mgr.

Now the only thing resource soc update does is read
the clock table and apply any DC specific policy decisions
to how clocks are populated in dml soc.

Reviewed-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: implement dc_mode_memclk

why:
Need interface to lower clocks when in dc (power save)
mode. Must be able to work with p_state unsupported cases
Can cause flicker when OS notifies us of dc state change

how:
added dal3 interface for KMD
added pathway to query smu for this softmax
added blank before clock change to override underflow
added logic to change clk based on pstatesupport and softmax
added logic in prepare/optimize_bw to conform while changing
clocks

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/display: fold DRM_AMD_DC_DCN3_1 into DRM_AMD_DC_DCN

No need for a separate flag now that DCN3.1 is not in bring up.
Fold into DRM_AMD_DC_DCN like previous DCN IPs.

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DCN3.1 clock manager support

Adds support for clock requests for the various parts of the DCN3.1 IP
and the interfaces and definitions for sending messages to SMU/PMFW.

Includes new support for z9/10, detecting SMU timeout and p-state
support enablement.

Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Disable MALL when SMU not present

[Why]
Bring-up purpose code to disable DMUB calling into
SMU and timeout for MALL when SMU is not present.

[How]
Disable MALL when SMU is not present.

Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: hide VGH asic specific structs

The pmfw structs are specific to the asic and should not be
present in base clk_mgr struct

v2: squash in SI fix (Alex)

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fold CONFIG_DRM_AMD_DC_DCN3* into CONFIG_DRM_AMD_DC_DCN (v3)

Avoids confusion in configurations.

v2: fix build when CONFIG_DRM_AMD_DC_DCN is disabled
v3: rebase on latest code

Reviewed-by: Luben Tuikov <luben.tuikov@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add dcn3.01 support to DC (v2)

Update dc for vangogh support.

v2: fix compilation without DCN 301 set.

Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Send DISPLAY_OFF after power down on boot

[WHY]
update_clocks might not be called on headless adapters. This means
DISPLAY_OFF may not be sent in headless cases.

[HOW]
If hardware is powered down on boot because it is headless (mode set
does not happen on that adapter) also send DISPLAY_OFF notification.

Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Send DISPLAY_OFF after power down on boot

[WHY]
update_clocks might not be called on headless adapters. This means
DISPLAY_OFF may not be sent in headless cases.

[HOW]
If hardware is powered down on boot because it is headless (mode set
does not happen on that adapter) also send DISPLAY_OFF notification.

Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Request PHYCLK adjustment on PHY enable/disable

[Why]
Currently we don't explicitly send a request for a minimum PHYCLK, and
we hope that the dependencies other clocks have will raise PHYCLK when
needed.

[How]
- new clk_mgr function to keep track of PHYCLK requirements
- request maximum requirement across all links
- remove PHYCLK from clock state comparator, as it doesn't come from DML

Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add support for per-state dummy-pstate latency

[why]
Dummy pstate latency actually varies between different
UCLK frequencies, when calculating watermark C, if DAL
always assumes worst case, then it can lead to dummy
pstate not supported scenarios.

[how]
Rather than statically calculating dummy pstate using
worst case, we store the entire table of UCLK to dummy
pstate relationships. On a per mode basis, we calculate
the actual UCLK lower limit, and use the dynamic worst
case dummy pstate latency. This prevents the situation
where we don't support full p-state (which will force
high DPM), but still use low DPM dummy pstate latency.

Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DCN3 CLK_MGR

Adds support for handling of clocking relevant to the DCN3 block

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add wm ranges to clk_mgr

[WHY & HOW]
Having watermark ranges saved inside clk_mgr to be
available for debug at all times would be useful.
Add it to the clk_mgr_internal struct for reference.
Only populated for Renoir, unused for other asics.

Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: update sr and pstate latencies for Renoir

[Why]
DF team has produced more optimized latency numbers.

[How]
Add sr latencies to the wm table, use different latencies
for different wm sets.
Also fix bb override from registery key for these latencies.

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix dprefclk and ss percentage reading on RN

[Why]
Before was using HW counter value to determine the dprefclk. Which
take into account ss, but has large variation, not good enough for
generating audio dto. Also, the bios parser code to get the ss
percentage was not working.

[How]
After this change, dprefclk is hard coded, same as on RV. We don't
expect this to change on Renoir. Modified bios parser code to get
the right ss percentage.

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: update sr and pstate latencies for Renoir

[Why]
DF team has produced more optimized latency numbers.

[How]
Add sr latencies to the wm table, use different latencies
for different wm sets.
Also fix bb override from registery key for these latencies.

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Drop CONFIG_DRM_AMD_DC_DCN2_1 flag

[Why]

DCN21 is stable enough to be build by default. So drop the flags.

[How]

Remove them using the unifdef tool. The following commands were executed
in sequence:

$ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DCN2_1 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_1 '{}' ';'
$ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DCN2_1 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_1 '{}' ';'

In addition:

* Remove from kconfig, and replace any dependencies with DCN1_0.
* Remove from any makefiles.
* Fix and cleanup Renoir definitions in dal_asic_id.h
* Expand DCN1 ifdef to include DCN21 code in the following files:
* clk_mgr/clk_mgr.c: dc_clk_mgr_create()
* core/dc_resources.c: dc_create_resource_pool()
* gpio/hw_factory.c: dal_hw_factory_init()
* gpio/hw_translate.c: dal_hw_translate_init()

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: move wm ranges reporting to end of init hw

[Why]
SMU does not keep the wm table across S3, S4, need to re-send
the table. Also defer sending the cable to after DCN bave initialized

[How]
Send table at end of init hw

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: move dispclk vco freq to clk mgr base

This value will be needed by dml and therefore should be externally
accessible.

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add renoir specific watermark range and clk helper

Doing this allows us to split it for diffrent asics. This design will
be helpful for future Asciis.

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: exit PSR during detection

[Why]
If 48mhz refclk is turned off during PSR, we will have issue doing
link training during detection.

[How]
Get out of PSR before detection

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add explicit comparator as default optimization check

[why]
memcmp is vulnerable to regression due to dc_clocks structures not being
organized properly (not "current" clock related structures being at the beginning
of the structure) and causes unnecessary setting of the optimize bit

[how]
add a dcn sepcific comparator, implement for dcn2

Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add Renoir clock manager

Controls display clocks and interfaces with powerplay for
clock and power requirements.

Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add set and get clock for testing purposes

add dc_set_clock
add dc_get_clock

this is for testing and diagnostics to get/set DPPCLK and DISPCLK.

Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix null-deref on vega20 with xgmi

[Why]
After clkmgr rework it gets initialized after resource pool.
The clkmgr is used in resource pool init for xgmi path.
That causes driver crash on Vega20 with xgmi due to NULL deref.

[How]
Move xgmi compensation code to dce121_clk_mgr_construct()
That also allows to make dce121_clock_patch_xgmi_ss_info()
internal static function.

Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Refactor clk_mgr functions

[Why]
Some HW specific implementations can be pulled out into clk_mgr.c.

[How]
* Pull get_active_display_cnt out to clk_mgr.
* Pull out shared logic in set_dispclk and set_dprefclk

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: make clk mgr soc specific

[Why]
First step of refactoring clk mgr to better handle different
ways of handling clock operations. Clock operation policies are
soc specific and not just DCN vesion specific. It is not a hw resource,
should not be in the resource pool.

[How]
Change clock manager creation to be based on HW internal ID, rename
clock manager members to be more clear. Move clock manager out of
resource.

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Set dispclk and dprefclock directly

[Why]
To simply logic for setting DCN specific clocks, we will send
SMU message directly through the VBIOS message box.

[How]
Add new structure in pp_smu to hold functions to set clocks
through vbios message box

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Create clock funcs

Create dccg_init and init_clocks for future use

Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: rename dccg to clk_mgr

In preparation for adding the actual dccg block since the
current implementation of dccg is mor eof a clock manager
than a hw block

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>