drm/amd/display: Fix potential null pointer dereference in dc_dmub_srv

Fixes potential null pointer dereference warnings in the
dc_dmub_srv_cmd_list_queue_execute() and dc_dmub_srv_is_hw_pwr_up()
functions.

In both functions, the 'dc_dmub_srv' variable was being dereferenced
before it was checked for null. This could lead to a null pointer
dereference if 'dc_dmub_srv' is null. The fix is to check if
'dc_dmub_srv' is null before dereferencing it.

Thus moving the null checks for 'dc_dmub_srv' to the beginning of the
functions to ensure that 'dc_dmub_srv' is not null when it is
dereferenced.

Found by smatch & thus fixing the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:133 dc_dmub_srv_cmd_list_queue_execute() warn: variable dereferenced before check 'dc_dmub_srv' (see line 128)
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:1167 dc_dmub_srv_is_hw_pwr_up() warn: variable dereferenced before check 'dc_dmub_srv' (see line 1164)

Fixes: 028bac583449 ("drm/amd/display: decouple dmcub execution to reduce lock granularity")
Fixes: 65138eb72e1f ("drm/amd/display: Add DCN35 DMUB")
Cc: JinZe.Xu <jinze.xu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Josip Pavic <josip.pavic@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add shared firmware state for DMUB IPS handshake

[Why]
Read modify write hazards can occur when using a single shared scratch
register between driver and firmware leading to driver accessing DCN
in IPS2 and a system hang.

[How]
Add infrastructure for using REGION6 as a shared firmware state between
driver and firmware. This region is uncachable.

Replace the existing get/set idle calls with reads/writes to the
(volatile) shared firmware state blocks that a separated by at least
a cache line between firmware and driver.

Remove the workarounds that required rewriting/checking read modify
write hazards.

Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Disable idle reallow as part of command/gpint execution

[Why]
Workaroud for a race condition where DMCUB is in the process of
committing to IPS1 during the handshake causing us to miss the
transition into IPS2 and touch the INBOX1 RPTR causing a HW hang.

[How]
Disable the reallow to ensure that we have enough of a gap between entry
and exit and we're not seeing back-to-back wake_and_executes.

Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Disable timeout in more places for dc_dmub_srv

[Why]
We're still missing a few and we'd like to avoid continuining when
a hang occurs for debug purposes.

[How]
Add the loop anywhere we try to wait on rptr == wptr in dc_dmub_srv.

Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Populate invalid split index to be 0xF

[why]
There exists scenarios where the split index for subvp can be
pipe index 0. The assumption in FW is that the split index
won't be 0 but this is incorrect.

[how]
Instead populate non-split cases to be 0xF to differentiate
between split and non-split.

Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: use correct phantom pipe when populating subvp pipe info

[why]
In current code, we recognize a pipe as a phantom pipe if it references
the same phantom stream. However it can also a phantom split pipe.
If the phantom split pipe has a smaller pipe index than the phantom pipe
we will mistakenly use the phantom split pipe as the phantom pipe. This
causes an incorrect subvp configuration where the first half of the
screen is flashing solid white image.

[how]
Add additional check that the pipe needs to be an OTG master pipe.

Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Wait before sending idle allow and after idle disallow

[Why]
We want acknowledgment of the driver idle disallow from DMCUB before
continuing with any further programming.

For idle allow we want to minimize the chance of DMCUB actively
interacing with other firmware components on the system (eg. PMFW)
at the same time.

[How]
Ensure that DMCUB isn't in the middle of processing other command
submissions prior to allowing idle and after disallowing idle by
inserting a wait before the allow and by changing the wait type for
the idle disallow.

Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix potential null pointer dereference in dc_dmub_srv

Fixes potential null pointer dereference warnings in the
dc_dmub_srv_cmd_list_queue_execute() and dc_dmub_srv_is_hw_pwr_up()
functions.

In both functions, the 'dc_dmub_srv' variable was being dereferenced
before it was checked for null. This could lead to a null pointer
dereference if 'dc_dmub_srv' is null. The fix is to check if
'dc_dmub_srv' is null before dereferencing it.

Thus moving the null checks for 'dc_dmub_srv' to the beginning of the
functions to ensure that 'dc_dmub_srv' is not null when it is
dereferenced.

Found by smatch & thus fixing the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:133 dc_dmub_srv_cmd_list_queue_execute() warn: variable dereferenced before check 'dc_dmub_srv' (see line 128)
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:1167 dc_dmub_srv_is_hw_pwr_up() warn: variable dereferenced before check 'dc_dmub_srv' (see line 1164)

Fixes: 028bac583449 ("drm/amd/display: decouple dmcub execution to reduce lock granularity")
Fixes: 65138eb72e1f ("drm/amd/display: Add DCN35 DMUB")
Cc: JinZe.Xu <jinze.xu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Josip Pavic <josip.pavic@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Address function parameter 'context' not described in 'dc_state_rem_all_planes_for_stream' & 'populate_subvp_cmd_drr_info'

Fixes the following gcc with W=1:

drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_state.c:524: warning: Function parameter or member 'state' not described in 'dc_state_rem_all_planes_for_stream'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_state.c:524: warning: Excess function parameter 'context' description in 'dc_state_rem_all_planes_for_stream'
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:540: warning: Function parameter or member 'context' not described in 'populate_subvp_cmd_drr_info'

Suggested-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Dillon Varone <dillon.varone@amd.com>
Cc: Jun Lei <jun.lei@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Srinath Rao <srinath.rao@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Verify disallow bits were cleared for idle

[Why]
A hang was observed where a read-modify-write access occurred due to the
register for idle state being shared between DMCUB and driver.

dmcub read - idle allow / no commit
driver read - idle allow / no commit
driver write - idle disallow / no commit
dmcub write - idle allow / commit

Resulting in DMCUB re-entering IPS after a disable and keeping the allow
high.

[How]
Long term we need to split commit/allow into two registers or use shared
DRAM state, but short term we can reduce the repro rate by ensuring that
the disallow went through by bounding the expected worst case scenario.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Switch DMCUB notify idle command to NO_WAIT

[Why]
Race condition between notification of driver idle and the command being
processed. We could theoretically enter idle between the submission and
the wait for idle that occurs after.

[How]
Switch the notification to NO_WAIT to avoid the RPTR access.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Wait forever for DMCUB to wake up

[Why]
If we time out waiting for PMFW to finish the exit sequence and touch
the DMCUB register the system will hang in a hard locked state.

[How]
Pol forever. This covers the case where things take too long but also
enables for debugging to occur since the cores won't be hardlocked.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Always exit DMCUB idle when called

[Why]
dc->idle_optimizations_allowed may be desynced with the hardware state.

[How]
Make sure we always exit out when dc_dmub_srv_exit_low_power_state is
called by removing the check.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Refactor phantom resource allocation

[WHY?]
Phantom streams and planes were previously not referenced explcitly on creation.

[HOW?]
To reduce memory management complexity, add an additional phantom streams and planes
reference into dc_state, and move mall_stream_config to stream_status inside
the state to make it safe to modify in shallow copies. Also consildates any logic
that is affected by this change to dc_state.

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Refactor dc_state interface

[WHY?]
Part of the dc_state interface that deals with adding streams and planes should
remain public, while others that deal with internal status' and subvp should be
private to DC.

[HOW?]
Move and rename the public functions to dc_state.h and private functions to
dc_state_priv.h. Also add some additional functions for extracting subvp meta
data from the state.

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Wake DMCUB before executing GPINT commands

[Why]
DMCUB can be in idle when we attempt to interface with the HW through
the GPINT mailbox resulting in a system hang.

[How]
Add dc_wake_and_execute_gpint() to wrap the wake, execute, sleep
sequence.

If the GPINT executes successfully then DMCUB will be put back into
sleep after the optional response is returned.

It functions similar to the inbox command interface.

Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Wake DMCUB before sending a command

[Why]
We can hang in place trying to send commands when the DMCUB isn't
powered on.

[How]
For functions that execute within a DC context or DC lock we can
wrap the direct calls to dm_execute_dmub_cmd/list with code that
exits idle power optimizations and reallows once we're done with
the command submission on success.

For DM direct submissions the DM will need to manage the enter/exit
sequencing manually.

We cannot invoke a DMCUB command directly within the DM execution
helper or we can deadlock.

Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Refactor DMCUB enter/exit idle interface

[Why]
We can hang in place trying to send commands when the DMCUB isn't
powered on.

[How]
We need to exit out of the idle state prior to sending a command,
but the process that performs the exit also invokes a command itself.

Fixing this issue involves the following:

1. Using a software state to track whether or not we need to start
the process to exit idle or notify idle.

It's possible for the hardware to have exited an idle state without
driver knowledge, but entering one is always restricted to a driver
allow - which makes the SW state vs HW state mismatch issue purely one
of optimization, which should seldomly be hit, if at all.

2. Refactor any instances of exit/notify idle to use a single wrapper
that maintains this SW state.

This works simialr to dc_allow_idle_optimizations, but works at the
DMCUB level and makes sure the state is marked prior to any notify/exit
idle so we don't enter an infinite loop.

3. Make sure we exit out of idle prior to sending any commands or
waiting for DMCUB idle.

This patch takes care of 1/2. A future patch will take care of wrapping
DMCUB command submission with calls to this new interface.

Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: skip error logging when DMUB is inactive from S3

[Why]
On resume from S3, while DMUB is inactive, DMUB queue and execute
calls will not work. Skip reporting errors in these scenarios

[How]
Add new return code during DMUB queue and execute calls when DMUB
is in S3 state. Skip logging errors in these scenarios

Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: do not send commands to DMUB if DMUB is inactive from S3

[Why]
On resume from S3, may get apply_idle_optimizations call while DMUB
is inactive which will just time out.

[How]
Set and track power state in dmub_srv and check power state before
sending commands to DMUB. Add interface in both dmub_srv and
dc_dmub_srv

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add disable timeout option

[WHY]
Driver continues running whenever there is
is timeout from smu or dmcub.

It is difficult to track failure state
when dcn, dc or dmcub changes on root failure.

[HOW]
Add disable_timeout option to halt driver
whenever there is a failure in response.

Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Negate IPS allow and commit bits

[WHY]
On s0i3, IPS mask isn't saved and restored.
It is reset to zero on exit.

If it is cleared unexpectedly, driver will
proceed operations while DCN is in IPS2 and
cause a hang.

[HOW]
Negate the bit logic. Default value of
zero indicates it is still in IPS2. Driver
must poll for the bit to assert.

Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: decouple dmcub execution to reduce lock granularity

[Why]
On some systems dmub commands run at high IRQ, so long running
commands will block other interrupts.

[How]
Decouple wait_for_idle from dmcub queue/execute/wait.

Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: JinZe.Xu <jinze.xu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix IPS handshake for idle optimizations

[Why]
Intermittent reboot hangs are observed introduced by
"Improve x86 and dmub ips handshake".

[How]
Bring back the commit but fix the polling.

Avoid hanging in place forever by bounding the delay and ensure that
we still message DMCUB on IPS2 exit to notify driver idle has been
cleared.

Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Revert "Improve x86 and dmub ips handshake"

This reverts commit 1288d702080949f87688d49dfeeacc99f40adc9b.

Causes intermittent hangs during reboot stress testing.

Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: switch DC over to the new DRM logging macros

For multi-GPU systems it is difficult to tell which GPU a particular
message is being printed for and that is undesirable because it
complicates debugging efforts. Also, the new macros allow us to enable
logging for particular parts of the codebase more selectively (since we
no longer need to throw everything at DRM_DEBUG_KMS()). So, for the
reasons outlined above we should switch to the new macros.

We can accomplish this by using the existing DC_LOGGER code to pass
around the relevant `struct drm_device` which will be fed to the new
macros in logger_types.h. Also, we must get rid of all instances of the
DC_LOG_.*() functions that are currently in amdgpu_dm since we don't use
the DC logger there and we can simply refer to the macros directly
there instead.

Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Improve x86 and dmub ips handshake

[Why]
There is a race condition between x86 and dmcub fw when attempting to exit
IPS2. Scenarios including exiting IPS2 before IPS2 has been entered. This
can cause unexpected hang when DMCUB attempt to exit while PMFW still
tries to enter IPS2.

[How]
A new design has been introduced to remove race conditions and improve the
handshake between x86 and DMCUB. An AON scratch register is borrowed from
PMFW to determine whether DMCUB has committed to IPS entry or not.

In the case when dmcub has committed IPS entry, x86 must poll until an exit
event occurred either from DMCUB(IPS1) or PMFW(IPS2). x86 will wait
upperbound of evaluation and IPS entry time to ensure IPS2 exit event has
been sent to PMFW.

Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Update driver and IPS interop

[Why]
Two issues fixed:

1. Currently, driver does not allow idle prior to PSR entry. Once
PSR1+IPS is enabled, there is intermittent hang due to DCN access
from IrqMgr during IPS2.

2. Driver is sending multiple commands to PMFW and dmcub to exit IPS
even during IPS0.

[How]
1. Set driver allow optimization prior to entering PSR mode with the
condition for eDP display only. Unregister all interrupts before
allowing driver idle and re-register interrupts when exiting from
idle. This will prevent IrqMgr to access DCN during IPS2.

2. Block sending PMFW and dmcub exit low power state commands when
driver is not in idle state.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add check for vrr_active_fixed

Why:
vrr_active_fixed should also be checked when
determining if DRR is in use

How:
Add check for vrr_active_fixed when allow_freesync
and vrr_active_variable are also checked

Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Austin Zheng <austin.zheng@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DCN35 DMUB

[Why & How]
Add DMUB handling for DCN35.

Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: ensure FS is enabled before sending request to DMUB for FS changes

[Why]
ignore_msa_timing_param indicates FS is capable but not necessarily enabled

[How]
add check for either allow_freesync or vrr_active_variable to confirm FS is enabled

Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Write flip addr to scratch reg for subvp

[Description]
SubVP needs to "calculate" the earliest in use META address
by using the current primary / meta addresses, but this leads
to a race condition where FW and driver can read/write the
address at the same time and intermittently produce inconsistent
address offsets. To mitigate this issue without locking (too slow),
save each surface flip addr into scratch registers and use this
to keep track of the earliest in use META addres.

Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: implement pipe type definition and adding accessors

[why]
There is a lack of encapsulation of pipe connection representation in pipe context.
This has caused many challenging bugs and coding errors with repeated
logic to identify the same pipe type.

[how]
Formally define pipe types and provide getters to identify a pipe type and
find a pipe based on specific requirements. Update existing logic in non dcn
specific files and dcn32 and future versions to use the new accessors.

Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add Replay supported/enabled checks

- Add checks for Cursor update and dirty rects (sending updates to dmub)
- Add checks for dc_notify_vsync, and fbc and subvp

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add interface to enable DPIA trace

[Why]
DPIA traces from DMUB is not enabled by default, which is
less convenient to debug DPIA related issues because we have
to resort to other debug tools to enable DPIA trace.

[How]
Exposes interfaces to update trace mask from the DMUB GPINT commands.
Also provides DC implementations to enable DPIA trace.

Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Skip querying caps when DMCUB emulation is in use

[Why]
Workaround to avoid accessing DMCUB state too early if the emulator
is in use - we don't support any of the features the caps are querying
with emulation anyway.

[How]
Guard the query if emulation is in use.

Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Set minimum requirement for using PSR-SU on Rembrandt

A number of parade TCONs are causing system hangs when utilized with
older DMUB firmware and PSR-SU. Some changes have been introduced into
DMUB firmware to add resilience against these failures.

Don't allow running PSR-SU unless on the newer firmware.

Cc: stable@vger.kernel.org
Cc: Sean Wang <sean.ns.wang@amd.com>
Cc: Marc Rossi <Marc.Rossi@amd.com>
Cc: Hamza Mahfooz <Hamza.Mahfooz@amd.com>
Cc: Tsung-hua (Ryan) Lin <Tsung-hua.Lin@amd.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2443
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix DMUB debugging print issue

[Why]
The DMUB diagnostic data was not printed out correctly.

[How]
Print the DMUB diagnostic data line by line.

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Cruise Hung <cruise.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix possible NULL dereference in dc_dmub_srv_cmd_run_list()

We have a NULL check for 'dc_dmub_srv' in dc_dmub_srv_cmd_run_list()
but we are dereferencing it before checking.

Fix this moving the dereference next to NULL check.

This issue is found with Smatch(static analysis tool).

Fixes: e97cc04fe0fb ("drm/amd/display: refactor dmub commands into single function")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: return status of dmub_srv_get_fw_boot_status

gcc with W=1 reports
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:
In function ‘dc_dmub_srv_optimized_init_done’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:184:26:
error: variable ‘dmub’ set but not used [-Werror=unused-but-set-variable]
184 | struct dmub_srv *dmub;
| ^~~~

The return status is never set.
It looks like a call to dmub_srv_get_fw_boot_status is missing.

Fixes: 499e4b1c722e ("drm/amd/display: add mechanism to skip DCN init")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add mechanism to skip DCN init

[Why]
If optimized init is done in FW. DCN init can be skipped in driver. This
need to be communicated between driver and fw and maintain backwards
compatibility.

[How]
Use DMUB scratch 0 bit 2 to indicate optimized init done in fw and
use DMUB scatch 4 bit 0 to indicate drive supports the optimized flow
so FW will perform it.

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: drain dmub inbox if queue is full

[Why & How]
If dmub command queuing fails due to the inbox being full, flush the
inbox and resubmit the comamnd. This was previously the default behavior
but was lost in a refactor.

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: refactor dmub commands into single function

[Why & How]
Consolidate dmub access to a single interface. This makes it easier to
add code in the future that needs to run every time a dmub command is
requested (e.g. instrumentation, locking etc).

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add FPO + VActive support

[Description]
- When determining FPO support, include FPO + VActive support
- Support FPO + VActive if one display meets regular requirements
for FPO and the second display is able to switch in VACTIVE with
a given amount of margin

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Uncomment assignments after HW headers are promoted

[Description]
Assign the correct info now that FW headers are promoted

Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Use per pipe P-State force for FPO

[Description]
* Pass in pipe index for FPO cmd to DMCUB
- This change will pass in the pipe index for each stream
that is using FPO
- This change is in preparation to enable FPO + VActive

* Use per pipe P-State force for FPO
- For FPO, instead of using max watermarks value for P-State disallow,
use per pipe p-state force instead
- This is in preparation to enable FPO + VActive

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Pass tg and hubp inst instead of pipe index for SubVP

[Description]
- For pipe harvesting cases, the pipe index does not necessarily
match up with the OTG instance, so pass index by OTG Instance instead
- For pipe split cases pass HUBP instance, since the split index is
only used for HUBP programming
- Also check for OPP ID when accessing opp for pipe harvesting cases

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Drop unnecessary DCN guards

[Why & How]
DC is littered with many DCN guards that are not needed.
Drop them.

Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: populate subvp cmd info only for the top pipe

[Why]
System restart observed while changing the display resolution
to 8k with extended mode. Sytem restart was caused by a page fault.

[How]
When the driver populates subvp info it did it for both the pipes using
vblank which caused an outof bounds array access causing the page fault.
added checks to allow the top pipe only to fix this issue.

Co-authored-by: Ayush Gupta <ayush.gupta@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Ayush Gupta <ayush.gupta@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix excess arguments on kernel-doc

Remove arguments present on kernel-doc that are not present on the
function declaration and add the new ones if present.

Signed-off-by: Arthur Grillo <arthurgrillo@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add margin on DRR vblank start for subvp

[Description]
- Add margin for HUBP "jitter" for SubVp + DRR case
- Also do a min transition even if MPO is added on a
non SubVP pipe (i.e. added on DRR pipe for SubVP + DRR)

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add margin for max vblank time for SubVP + DRR

[Description]
- Incorporate FW delays as port of max VTOTAL calculated for
SubVP + DRR cases (since it is part of the microschedule).
- Also add margin for the max VTOTAL possible for SubVP + DRR cases.
- Due to rounding errors in FW (integer arithmetic), the microschedule
calculation can get pushed to the next frame (incorrectly) in cases
where we use the max VTOTAL possible to complete the MCLK switch.
- When the rounding error occurs, we are only off by 1-2 lines,
use 40us margin which is working consistently.

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Cursor update refactor: PSR-SU support condition

[Why]
PSR-SU requires extra conditions while cursor update.

Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Max Tseng <Max.Tseng@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Modify mismatched function name

No functional modification involved.

drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:615: warning: expecting prototype for setup_subvp_dmub_command(). Prototype was for populate_subvp_cmd_pipe_info() instead.

Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2587
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Convert documentation to a kernel-doc

The dc_dmub_srv file has a lot of documentation associated with SubVP
that could be converted to a kernel-doc. This commit just changes the
comment style to a kernel-doc.

Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix watermark calculation

Watermark calculation was incorrect due to missing brackets.

Fixes: 85f4bc0c333c ("drm/amd/display: Add SubVP required code")
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0

drm/amd/display: Use the same cursor info across features

Since different features would need to update cursor registers, However,
they would use different approaches.

To unify varied methods, this refactor is implemented the same update
cursor info method for current varied features.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Max Tseng <Max.Tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Uncomment SubVP pipe split assignment in driver

[Why & How]
Uncomment SubVP pipe split assignment in driver since FW headers
are now promoted

Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: SubVP pipe split case

[Why and How]
For SubVP pipe split case, pass in split index for
main and phantom pipes to ensure that the P-State
sequence will force P-State for all required pipes.

Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Refactor SubVP calculation to remove FPU

Refactor calculation to remove floating point operations from dmub_srv.
To ensure that 32-bit compilation works well, we use the div64 family of
macros to do integer division for SubVP-related timing parameters.

Cc: Maíra Canal <mairacanal@riseup.net>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Isabella Basso <isabbasso@riseup.net>
Cc: Magali Lemes <magalilemes00@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Co-developed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Co-developed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: SubVP missing scaling case

[Description]
For SubVP scaling case we have to combine
the plane scaling and stream scaling.

Use UCLK dummy p-state WM for FCLK WM set C

[Description]
For DCN32/321 program dummy UCLK P-state watermark into FCLK
watermark set C register.

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add support for visual confirm color

[Why]
We want to get the visual confirm color of the bottom-most pipe
for test automation.

[How]
Save the visual confirm color to plane_state before program to MPC;

Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix variable dereferenced before check

Fixes the following smatch warning:

drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:311 dc_dmub_srv_p_state_delegate()
warn: variable dereferenced before check 'dc' (see line 309)

Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: sunliming <sunliming@kylinos.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Uncomment SubVP scaling case

[Description]
Uncomment scaling cmd assignment since
FW headers are now promoted.

Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Refactor SubVP calculation to remove FPU

Refactor calculation to remove floating point operations from dmub_srv.
To ensure that 32-bit compilation works well, we use the div64 family of
macros to do integer division for SubVP-related timing parameters.

Cc: Maíra Canal <mairacanal@riseup.net>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Isabella Basso <isabbasso@riseup.net>
Cc: Magali Lemes <magalilemes00@gmail.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Co-developed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Co-developed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Include scaling factor for SubVP command

[Description]
For SubVP scaling cases, we must include the scaling
info as part of the cmd. This is required when converting
OTG line to HUBP line for the MALL_START_LINE programming.

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add 16 lines margin for SubVP

[Description]
SUBVP_START_LINE must be aligned to 2 swaths, so add
16 lines of margin so the start line can be adjusted by
up to 16 lines for alignment purposes in FW.

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Updates SubVP and SubVP DRR cases

[Description]
- For any DRR cases in SubVP, don't lock for VSYNC flips
- For DCN32/321 use FW to do DRR manual trigger programming
- Add bit in SubVP cmd to indicate if the SubVP pipe is DRR

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: make some dc_dmub_srv functions static

Not used outside of dc_dmub_srv.c.

Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix 32 bit compilation errors in dc_dmub_srv.c

There are several things wrong here. First, none of these
numbers are FP, so there is no need to cast to double. Next
make sure to use proper 64 bit division helpers.

Fixes: 85f4bc0c333c ("drm/amd/display: Add SubVP required code")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix non-x86/PPC64 compilation

Need to protect FP DMCUB code with CONFIG_DRM_AMD_DC_DCN.
Fixes build failures like the following on arm64:
ERROR: modpost: "__floatunsidf" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
ERROR: modpost: "__divdf3" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
ERROR: modpost: "fma" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
ERROR: modpost: "__adddf3" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
ERROR: modpost: "__fixdfsi" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
ERROR: modpost: "__muldf3" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
ERROR: modpost: "__floatsidf" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
ERROR: modpost: "__fixunsdfsi" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!

Fixes: 85f4bc0c333c ("drm/amd/display: Add SubVP required code")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add basic infrastructure for enabling FAMS

We want to enable Firmware Assisted Memory (FAMS) Switching, but first,
we need to add the required code infrastructure in DC before allowing it
in amdgpu_dm.

Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add SubVP required code

This commit enables the SubVP feature. To achieve that, we need to:

- Don't force p-state disallow on SubVP (can't block dummy p-state)
- Send calculated watermark to DMCUB for SubVP
- Adjust CAB mode message to PMFW
- Add a proper locking sequence for SubVP
- Various fixes to SubVP static analysis and determining SubVP config
- Currently SubVP not supported with pipe split so merge all pipes
before setting up SubVp

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Firmware assisted MCLK switch and FS

[WHY]
Memory clock switching has great potential for power savings.

[HOW]
The driver code was modified to notify the DMCUB firmware that it should
stretch the vertical blank of frames when a memory clock switch is about
to start so that no blackouts happen on the screen due to unavailability
of the frame buffer.
The driver logic to determine when such firmware assisted strategy can
be initiated is also implemented and consists on checking prerequisites
of the feature.

Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Felipe Clark <felipe.clark@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DMCUB source files and changes for DCN32/321

DMCUB is the display engine microcontroller which aids in modesetting
and other display related features.

Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Wait for ACK for INBOX0 HW Lock

[Why]
In DC we want to wait for the INBOX0 HW Lock command to ACK before
continuing. This is to ensure that the lock has been successfully
acquired before programming HW in DC.

[How]
Add interfaces to send messages on INBOX0, poll for their completation
and clear the ack.

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/display: fold DRM_AMD_DC_DCN3_1 into DRM_AMD_DC_DCN

No need for a separate flag now that DCN3.1 is not in bring up.
Fold into DRM_AMD_DC_DCN like previous DCN IPs.

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add DMUB registers to crash dump diagnostic data.

[WHY]
Ability to triage DMCUB is improved with availability of certain
dmub registers not currently captured in crash dump diagnostic data.

[HOW]
Add dmub registers to diagnostic data collection.

Thanks Nicholas Kazlauskas for awesome input on this!

Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DCN3.1 DMCUB

DMCU-B (Display Micro-Controller Unit B) is a display microcontroller
used for shared display functionality with BIOS and for advanced
power saving display features.

Extends the command header to include new DCN3.1 functionality.

Adds new interfaces to DC dmub interface as well for z-state support.

Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Implement INBOX0 usage in driver

[Why]
Start using INBOX0 for HW Lock command

[How]
- Implement initial interface for INBOX0 HW lock message

Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Support for DMUB AUX

[WHY]
To process AUX transactions with DMUB using inbox1 and outbox1 mail boxes.

[How]
1) Added inbox1 command DMUB_CMD__DP_AUX_ACCESS to issue AUX commands
to DMUB in dc_process_dmub_aux_transfer_async(). DMUB processes AUX cmd
with DCN and sends reply back in an outbox1 message triggering an
outbox1 interrupt to driver.
2) In existing driver implementation, AUX commands are processed
synchronously by configuring DCN reg. But in DMUB AUX, driver sends an
inbox1 message and waits for a conditional variable (CV) which will be
signaled by outbox1 ISR.
3) DM will retrieve Outbox1 message and send back reply to upper layer
and complete the AUX command

Signed-off-by: Jude Shih <shenshih@amd.com>
Reviewed-by: Hanghong Ma <Hanghong.Ma@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix typo for helpers function name

[why]
Word "helper" was misspelled as "helpes" in
dm_helpes_dmub_outbox0_interrupt_control function.

[how]
Fix the spelling.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fixed read/write pointer issue for get dmub trace

[Why]
Driver get wrap around dmub trace data due to read pointer being
increased incorrectly when there are multiple interrupt
queues with very short interval

[How]
Check read/write pointer before copying data from ring buffer

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Implement dmub trace event

[Why & How]
DMUB FW send trace event via outbox0 interrupt. Driver will handle it.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add dc_dmub_srv helpers for in/out DMCUB commands

[Why]
We added these in DMCUB for runtime feature detection
but we didn't have helpers to call these with DC error
handling/logging.

[How]
Add helpers.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: implement notify stream mask

[Why]
Send stream active state info to DMUB

[How]
Implement GPINT to notify stream mask

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Revert "drm/amd/display: add mechanism to skip DCN init"

To avoid s3 faild at the first cycle on renoir platform, it needs to
revert this patch:
drm/amd/display: add mechanism to skip DCN init

Signed-off-by: changfeng <Changfeng.Zhu@amd.com>
Ackedy-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add mechanism to skip DCN init

[Why]
If optimized init is done in FW. DCN init be skipped in driver. This
need to be communicated between driver and fw and maintain backwards
compatibility.

[How]
Use DMUB scratch 0 bit 2 to indicate optimized init done in fw and
use DMUB scatch 4 bit 0 to indicate drive supports the optimized flow
so FW will perform it.

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: move location of dmub_srv.h file

[Why]
Make a separation of what belongs in the differen dmub
headers

dmub_srv.h is for exposing dmub srv interface to rest of
driver.

other headers inside dmub/inc exposes cmds and definitions
that are owned by the firmware

[How]
keep firmware owned definitions in dmub/inc

move stuff that is purely driver interface headers to dmub/
since those are interface calls that are defined for rest of
driver to use

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Pass command instead of header into DMUB service

[Why]
We read memory that we shouldn't be touching if the struct isn't
a full union dmub_rb_cmd.

[How]
Fix up all the callers and functions that take in the dmub_cmd_header
to use the dmub_rb_cmd instead.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Spin for DMCUB PHY init in DC

[Why]
DCN will hang if we access registers before PHY init is done.

So we need to spin or abort.

[How]
On hardware with DMCUB running and working we shouldn't time out
waiting for this to finish and we shouldn't hit the spin cycle.

If there's no hardware support then we should exit out of the function
early assuming that PHY init was already done elsewhere.

If we hit the timeout then there's likely a bug in firmware or software
and we need to debug - add errors and asserts as appropriate.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Don't spin forever waiting for DMCUB phy/auto init

[Why]
It's an interface violation to use infinite loops within DMUB
service functions and we'll lock up the kernel by doing so.

[How]
Revert the function back to its intended functionality.
Move the infinite loops into DC/DM as necessary.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix spelling mistake "exeuction" -> "execution"

There are spelling mistakes in a DC_ERROR message and a comment.
Fix these.

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DMUB support to DC

DC will use DMUB for command submission and flow control during
initialization.

Register offloading as well as submitting some BIOS commands are part
of the DC internal interface but are guarded behind debug options.

It won't be functional in amdgpu_dm yet since we don't pass the
DMUB service to DC for use.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>