drm/amd/display: add debugfs disallow edp psr

[Why]
fix reading edp rx crc timeout failure. after
bootup, kernel setup psr with dpcd 0x170 = 5. this
notify rx psr enable and let rx fw start checking crc
for fw internal logic. rx fw may not update crc read
count within dpcd 0x246. read count is always 0. this
will lead tx crc reading timeout.

[How]
add debugfs to let test app to disbable rx crc
checking for rx internal logic. then test app can read
rx crc dpcd 0x246 successfully.
expected app sequence is as below:
1. disable eDP PHY and notify eDP rx with dpcd 0x600 = 2.
2. echo 0x1 /sys/kernel/debug/dri/0/eDP-X/disallow_edp_enter_psr
3. enable eDP PHY and notify eDP rx with dpcd 0x600 = 1 but
without dpcd 0x170 = 5.
4. read crc from rx dpcd 0x270, 0x246, etc.
5. echo 0x0 /sys/kernel/debug/dri/0/eDP-X/disallow_edp_enter_psr.
this will let eDP back to normal with psr setup dpcd 0x170 = 5.

Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Address kdoc for eDP Panel Replay feature in 'amdgpu_dm_crtc_set_panel_sr_feature()'

Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_crtc.c:100: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* The DRM vblank counter enable/disable action is used as the trigger
to enable

Cc: Sun peng Li <sunpeng.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Enable Panel Replay for static screen use case

[Why]
Enable the Panel Replay if eDP panel and ASIC support.
(prioritize Panel Replay over PSR)

[How]
- Setup the Panel Replay config during the device init
(prioritize Panel Replay over PSR).
- Separate the Replay init function into two functions
amdgpu_dm_link_setup_replay() and amdgpu_dm_set_replay_caps()
to fix the issue in the earlier commit that cause PSR and Replay
enabled at the same time.

Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix recent checkpatch errors in amdgpu_dm

- Use tabs, not spaces.
- Brace and parentheses placement

Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Re-revert "drm/amd/display: Enable Replay for static screen use cases"

This reverts commit 44e60b14d5a72f91fd0bdeae8da59ae37a3ca8e5.

Since, it causes a regression in which eDP displays with PSR support,
but no Replay support (Sink support <= 0x03), fail to enable PSR and
consequently all IGT amd_psr tests fail. So, revert this until a more
suitable fix can be found.

This got brought back accidently with the backmerge.

Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Ivan Lipski <ivlipski@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix documentation for dm_crtc_additional_color_mgmt()

warning: expecting prototype for drm_crtc_additional_color_mgmt().
Prototype was for dm_crtc_additional_color_mgmt() instead

Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312141801.o9eBCxt9-lkp@intel.com/
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add CRTC gamma TF driver-specific property

Add AMD pre-defined transfer function property to default DRM CRTC gamma
to convert to wire encoding with or without a user gamma LUT. There is
no post-blending regamma ROM for pre-defined TF. When setting Gamma TF
(!= Identity) and LUT at the same time, the color module will combine
the pre-defined TF and the custom LUT values into the LUT that's
actually programmed.

v2:
- enable CRTC prop in the end of driver-specific prop sequence
- define inverse EOTFs as supported regamma TFs
- reword driver-specific function doc to remove shaper/3D LUT

v3:
- spell out TF+LUT behavior in the commit and comments (Harry)

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Co-developed-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add prefix to amdgpu crtc functions

The ftrace debug feature allows filtering functions based on a prefix,
which can be helpful in some complex debug scenarios. The driver can
benefit more from this feature if the function name follows some
patterns; for this reason, this commit adds the prefix amdgpu_dm_crtc_
to all the functions that do not have it in the amdgpu_dm_crtc.c file.

Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Revert "drm/amd/display: Enable Replay for static screen use cases"

This reverts commit 44e60b14d5a72f91fd0bdeae8da59ae37a3ca8e5.

Since, it causes a regression in which eDP displays with PSR support,
but no Replay support (Sink support <= 0x03), fail to enable PSR and
consequently all IGT amd_psr tests fail. So, revert this until a more
suitable fix can be found.

Cc: stable@vger.kernel.org
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Ivan Lipski <ivlipski@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Enable Replay for static screen use cases

- Setup replay config on device init.
- Enable replay if feature is enabled (prioritize replay over PSR, since
it can be enabled in more usecases)
- Add debug masks to enable replay on supported ASICs

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Enable Replay for static screen use cases

- Setup replay config on device init.
- Enable replay if feature is enabled (prioritize replay over PSR, since
it can be enabled in more usecases)
- Add debug masks to enable replay on supported ASICs

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: ensure async flips are only accepted for fast updates

We should be checking to see if async flips are supported in
amdgpu_dm_atomic_check() (i.e. not dm_crtc_helper_atomic_check()). Also,
async flipping isn't supported if a plane's framebuffer changes memory
domains during an atomic commit. So, move the check from
dm_crtc_helper_atomic_check() to amdgpu_dm_atomic_check() and check if
the memory domain has changed in amdgpu_dm_atomic_check().

Cc: stable@vger.kernel.org
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2733
Fixes: c1e18c44dc7f ("drm/amd/display: only accept async flips for fast updates")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: only accept async flips for fast updates

Up until now, amdgpu was silently degrading to vsync when
user-space requested an async flip but the hardware didn't support
it.

The hardware doesn't support immediate flips when the update changes
the FB pitch, the DCC state, the rotation, enables or disables CRTCs
or planes, etc. This is reflected in the dm_crtc_state.update_type
field: UPDATE_TYPE_FAST means that immediate flip is supported.

Silently degrading async flips to vsync is not the expected behavior
from a uAPI point-of-view. Xorg expects async flips to fail if
unsupported, to be able to fall back to a blit. i915 already behaves
this way.

This patch aligns amdgpu with uAPI expectations and returns a failure
when an async flip is not possible.

Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: only accept async flips for fast updates

Up until now, amdgpu was silently degrading to vsync when
user-space requested an async flip but the hardware didn't support
it.

The hardware doesn't support immediate flips when the update changes
the FB pitch, the DCC state, the rotation, enables or disables CRTCs
or planes, etc. This is reflected in the dm_crtc_state.update_type
field: UPDATE_TYPE_FAST means that immediate flip is supported.

Silently degrading async flips to vsync is not the expected behavior
from a uAPI point-of-view. Xorg expects async flips to fail if
unsupported, to be able to fall back to a blit. i915 already behaves
this way.

This patch aligns amdgpu with uAPI expectations and returns a failure
when an async flip is not possible.

Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/amd/display: Fix warning in disabling vblank irq

[Why]
During gpu-reset, we toggle vblank irq by calling dc_interrupt_set()
instead of amdgpu_irq_get/put() because we don't want to change the irq
source's refcount. However, we see the warning when vblank irq is enabled
by dc_interrupt_set() during gpu-reset but disabled by amdgpu_irq_put()
after gpu-reset.

[How]
Only in dm_gpureset_toggle_interrupts() we toggle vblank interrupts by
calling dc_interrupt_set(). Apart from this we call dm_set_vblank()
which uses amdgpu_irq_get/put() to operate vblank irq.

Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alan Liu <haoping.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix warning in disabling vblank irq

[Why]
During gpu-reset, we toggle vblank irq by calling dc_interrupt_set()
instead of amdgpu_irq_get/put() because we don't want to change the irq
source's refcount. However, we see the warning when vblank irq is enabled
by dc_interrupt_set() during gpu-reset but disabled by amdgpu_irq_put()
after gpu-reset.

[How]
Only in dm_gpureset_toggle_interrupts() we toggle vblank interrupts by
calling dc_interrupt_set(). Apart from this we call dm_set_vblank()
which uses amdgpu_irq_get/put() to operate vblank irq.

Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alan Liu <haoping.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Fix desktop freezed after gpu-reset

[Why]
After gpu-reset, sometimes the driver fails to enable vblank irq,
causing flip_done timed out and the desktop freezed.

During gpu-reset, we disable and enable vblank irq in dm_suspend() and
dm_resume(). Later on in amdgpu_irq_gpu_reset_resume_helper(), we check
irqs' refcount and decide to enable or disable the irqs again.

However, we have 2 sets of API for controling vblank irq, one is
dm_vblank_get/put() and another is amdgpu_irq_get/put(). Each API has
its own refcount and flag to store the state of vblank irq, and they
are not synchronized.

In drm we use the first API to control vblank irq but in
amdgpu_irq_gpu_reset_resume_helper() we use the second set of API.

The failure happens when vblank irq was enabled by dm_vblank_get()
before gpu-reset, we have vblank->enabled true. However, during
gpu-reset, in amdgpu_irq_gpu_reset_resume_helper() vblank irq's state
checked from amdgpu_irq_update() is DISABLED. So finally it disables
vblank irq again. After gpu-reset, if there is a cursor plane commit,
the driver will try to enable vblank irq by calling drm_vblank_enable(),
but the vblank->enabled is still true, so it fails to turn on vblank
irq and causes flip_done can't be completed in vblank irq handler and
desktop become freezed.

[How]
Combining the 2 vblank control APIs by letting drm's API finally calls
amdgpu_irq's API, so the irq's refcount and state of both APIs can be
synchronized. Also add a check to prevent refcount from being less then
0 in amdgpu_irq_put().

v2:
- Add warning in amdgpu_irq_enable() if the irq is already disabled.
- Call dc_interrupt_set() in dm_set_vblank() to avoid refcount change
if it is in gpu-reset.

v3:
- Improve commit message and code comments.

Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add prefix to amdgpu_dm_crtc.h functions

Some amdgpu_dm_crtc.h functions didn't have names that indicated where
they were declared.

To better filter results in debug tools like ftrace, prefix these
functions with 'amdgpu_dm_crtc_'.

Signed-off-by: David Tadokoro <davidbtadokoro@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Fix desktop freezed after gpu-reset

[Why]
After gpu-reset, sometimes the driver fails to enable vblank irq,
causing flip_done timed out and the desktop freezed.

During gpu-reset, we disable and enable vblank irq in dm_suspend() and
dm_resume(). Later on in amdgpu_irq_gpu_reset_resume_helper(), we check
irqs' refcount and decide to enable or disable the irqs again.

However, we have 2 sets of API for controling vblank irq, one is
dm_vblank_get/put() and another is amdgpu_irq_get/put(). Each API has
its own refcount and flag to store the state of vblank irq, and they
are not synchronized.

In drm we use the first API to control vblank irq but in
amdgpu_irq_gpu_reset_resume_helper() we use the second set of API.

The failure happens when vblank irq was enabled by dm_vblank_get()
before gpu-reset, we have vblank->enabled true. However, during
gpu-reset, in amdgpu_irq_gpu_reset_resume_helper() vblank irq's state
checked from amdgpu_irq_update() is DISABLED. So finally it disables
vblank irq again. After gpu-reset, if there is a cursor plane commit,
the driver will try to enable vblank irq by calling drm_vblank_enable(),
but the vblank->enabled is still true, so it fails to turn on vblank
irq and causes flip_done can't be completed in vblank irq handler and
desktop become freezed.

[How]
Combining the 2 vblank control APIs by letting drm's API finally calls
amdgpu_irq's API, so the irq's refcount and state of both APIs can be
synchronized. Also add a check to prevent refcount from being less then
0 in amdgpu_irq_put().

v2:
- Add warning in amdgpu_irq_enable() if the irq is already disabled.
- Call dc_interrupt_set() in dm_set_vblank() to avoid refcount change
if it is in gpu-reset.

v3:
- Improve commit message and code comments.

Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/amd/display: don't call dc_interrupt_set() for disabled crtcs

As made mention of in commit 4ea7fc09539b ("drm/amd/display: Do not
program interrupt status on disabled crtc"), we shouldn't program
disabled crtcs. So, filter out disabled crtcs in dm_set_vupdate_irq()
and dm_set_vblank().

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Fixes: 589d2739332d ("drm/amd/display: Use crtc enable/disable_vblank hooks")
Fixes: d2574c33bb71 ("drm/amd/display: In VRR mode, do DRM core vblank handling at end of vblank. (v2)")
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Conversion to bool not necessary

A logical evaluation already results in bool. There is no need for using
a ternary operator based evaluation and bool conversion of the outcome.
Issue identified using boolconv.cocci Coccinelle semantic patch.
This was also reported by the Kernel Test Robot. Hence

Fixes: 473683a03495 ("drm/amd/display: Create a file dedicated for CRTC")

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Deepak R Varma <drv@mailo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: don't enable DRM CRTC degamma property for DCE

DM maps DRM CRTC degamma to DPP (pre-blending) degamma block, but DCE doesn't
support programmable degamma curve anywhere. Currently, a custom degamma is
accepted by DM but just ignored by DCE driver and degamma correction isn't
actually applied. There is no way to map custom degamma in DCE, therefore, DRM
CRTC degamma property shouldn't be enabled for DCE drivers.

Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Implement secure display on DCN21

[Why]
Porting secure display feature from DCN10 to DCN21. Support single
display for now and will extend to multiple displays.

[How]
- use workqueue to offload works for dmub or dmcu firmware
- after receiving ROI update from userspace, set skip_frame_cnt to 1
- refactor amdgpu_dm_crtc_handle_crc_window_irq()
- disable PSR before activating secure_display on a crtc
- check if secure_display is activated before enabling psr
- only work for single display for now.

Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: don't enable DRM CRTC degamma property for DCE

DM maps DRM CRTC degamma to DPP (pre-blending) degamma block, but DCE doesn't
support programmable degamma curve anywhere. Currently, a custom degamma is
accepted by DM but just ignored by DCE driver and degamma correction isn't
actually applied. There is no way to map custom degamma in DCE, therefore, DRM
CRTC degamma property shouldn't be enabled for DCE drivers.

Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/amd/display: Copy crc_skip_count when duplicating CRTC state

[Why]

crc_skip_count is used to track how many frames to skip to allow the OTG
CRC engine to "warm up" before it outputs correct CRC values.
Experimentally, this seems to be 2 frames.

When duplicating CRTC states, this value was not copied to the
duplicated state. Therefore, when this state is committed, we will
needlessly wait 2 frames before outputing CRC values. Even if the CRC
engine is already warmed up.

[How]

Copy the crc_skip_count as part of dm_crtc_duplicate_state.

Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Create a file dedicated for CRTC

[Why]
The amdgpu_dm file contains most of the code that works as an interface
between DRM API and DC. As a result, this file becomes very large since
it comprises multiple abstractions such as CRTC manipulation.

[How]
This commit extracts the CRTC code to its specific file named
amdgpu_dm_crtc. This change does not change anything inside the
functions; the only exception is converting some static functions to a
global function.

v2: fix ifdef merge mix up (Alex)

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>