firmware: ti_sci: rm: Add new ops for ring configuration

The sysfw ring configuration message has been extended to include virtid
and asel value for the ring.
Add the ASEL_VALID to TI_SCI_MSG_VALUE_RM_ALL_NO_ORDER as it is required
for DMA rings.

Instead of extending the current .config() ops - which would need same
patch change in the ringacc driver - add ti_sci_msg_rm_ring_cfg struct and
a new ops using it to configure the ring.

This will allow easy update path in case new members are added for the ring
configuration.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>

firmware: ti_sci: rm: Remove ring_get_config support

The ring_get_cfg (0x1111 message) is not used and it is not supported by
sysfw for a long time.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>

firmware: ti_sci: rm: Add support for extended_ch_type for tx channel

Sysfw added 'extended_ch_type' to the tx_ch_cfg_req message which should be
used when BCDMA block copy channels are configured:
extended_ch_type = 0 : the channel is split tx channel (tchan)
extended_ch_type = 1 : the channel is block copy channel (bchan)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>

firmware: ti_sci: rm: Add support for second resource range

Sysfw added support for a second range in the resource range API to be able
to describe complex allocations mainly for DMA channels.

Update the ti_sci part to consider the second range as well.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>

firmware: ti_sci: rm: Add support for tx_tdtype parameter for tx channel

The system controller's resource manager have support for configuring the
TDTYPE of TCHAN_CFG register on j721e.
With this parameter the teardown completion can be controlled:
TDTYPE == 0: Return without waiting for peer to complete the teardown
TDTYPE == 1: Wait for peer to complete the teardown

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>

firmware: ti_sci: Replace HTTP links with HTTPS ones

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.

Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>

firmware: ti_sci: Use the correct style for SPDX License Identifier

This patch corrects the SPDX License Identifier style
in header file related to Firmware Drivers for Texas
Instruments SCI Protocol.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46

Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: ti_sci: Use the correct style for SPDX License Identifier

This patch corrects the SPDX License Identifier style
in header file related to Firmware Drivers for Texas
Instruments SCI Protocol.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>

firmware: ti_sci: Add support for processor control

Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used in Texas Instrument's System on Chip (SoC) such as those
in K3 family AM654 SoC to communicate between various compute
processors with a central system controller entity.

The system controller provides various services including the control
of other compute processors within the SoC. Extend the TI-SCI protocol
support to add various TI-SCI commands to invoke services associated
with power and reset control, and boot vector management of the
various compute processors from the Linux kernel.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>

firmware: ti_sci: Add resource management APIs for ringacc, psi-l and udma

Configuration of NAVSS resource, like rings, UDMAP channels, flows
and PSI-L thread management need to be done via TISCI.

Add the needed structures and functions for NAVSS resource configuration of
the following:
Rings from Ring Accelerator
PSI-L thread management
UDMAP tchan, rchan and rflow configuration.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>

firmware: ti_sci: extend clock identifiers from u8 to u32

Future SoCs are going to have more than 255 device clocks in certain cases,
and thus the API must be extended to support this. The support is done in
backwards compatible extension, in which the new u32 clock identifier
fields are only used if the existing u8 size clock identifier is set as
255. In all the other cases, the existing u8 clock identifier is used. As
the size of the messages sent / received is not verified for existing
devices / old firmware, increasing the size of the messages from the end
is also fine. Due to this reason, depending on ABI version isn't necessary
either.

Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

firmware: ti_sci: Add support for IRQ management

TISCI abstracts the handling of IRQ routes where interrupt sources
are not directly connected to host interrupt controller. Add support
for the set of TISCI commands for requesting and releasing IRQs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

firmware: ti_sci: Add support for RM core ops

TISCI provides support for getting the resources(IRQ, RING etc..)
assigned to a specific device. These resources can be handled by
the client and in turn sends TISCI cmd to configure the resources.

It is very important that client should keep track on usage of these
resources.

Add support for TISCI commands to get resource ranges.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

firmware: ti_sci: Switch to SPDX Licensing

Switch to SPDX licensing and drop the GPL text which comes redundant.

Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>

firmware: ti_sci: Add support for reboot core service

Since system controller now has control over SoC power management, it
needs to be explicitly requested to reboot the SoC. Add support for
it.

In some systems however, SoC needs to toggle a GPIO or send event to an
external entity (like a PMIC) for a system reboot to take place. To
facilitate that, we allow for a DT property to determine if the reboot
handler will be registered and further, the service is also made
available to other drivers (such as PMIC driver) to sequence the
additional operation and trigger the SoC reboot as the last step.

Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

firmware: ti_sci: Add support for Clock control

Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used in Texas Instrument's System on Chip (SoC) such as those
in keystone family K2G SoC to communicate between various compute
processors with a central system controller entity.

TI-SCI message protocol provides support for management of various
hardware entities within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.

In general, we expect to function at a device level of abstraction,
however, for proper operation of hardware blocks, many clocks directly
supplying the hardware block needs to be queried or configured.

Introduce support for the set of SCI message protocol support that
provide us with this capability.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

firmware: ti_sci: Add support for Device control

Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used in Texas Instrument's System on Chip (SoC) such as those
in keystone family K2G SoC to communicate between various compute
processors with a central system controller entity.

TI-SCI message protocol provides support for management of various
hardware entitites within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.

We introduce the fundamental device management capability support to
the driver protocol as part of this change.

[d-gerlach@ti.com: Contributed device reset handling]
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

firmware: Add basic support for TI System Control Interface (TI-SCI) protocol

Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used in Texas Instrument's System on Chip (SoC) such as those
in keystone family K2G SoC to communicate between various compute
processors with a central system controller entity.

TI-SCI message protocol provides support for management of various
hardware entities within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.

We introduce the basic registration and query capability for the
driver protocol as part of this change. Subsequent patches add in
functionality specific to the TI-SCI features.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>