video: Add helpers for decoding screen_info

The plain values as stored in struct screen_info need to be decoded
before being used. Add helpers that decode the type of video output
and the framebuffer I/O aperture.

Old or non-x86 systems may not set the type of video directly, but
only indicate the presence by storing 0x01 in orig_video_isVGA. The
decoding logic in screen_info_video_type() takes this into account.
It then follows similar code in vgacon's vgacon_startup() to detect
the video type from the given values.

A call to screen_info_resources() returns all known resources of the
given screen_info. The resources' values have been taken from existing
code in vgacon and vga16fb. These drivers can later be converted to
use the new interfaces.

v2:
* return ssize_t from screen_info_resources()
* don't call __screen_info_has_lfb() unnecessarily

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240212090736.11464-2-tzimmermann@suse.de

firmware: microchip: add PolarFire SoC Auto Update support

Add support for Auto Update reprogramming of the FPGA fabric on
PolarFire SoC, using the fw_upload mechanism a la the
intel-m10-bmc-sec-update driver.

This driver only writes the image to the spi flash & performs
validation on it, as the entire FPGA becomes unusable during the actual
reprogramming of a bitstream. To initiate the reprogramming itself, a
device reset is required. The SBI SRST extension's "cold reboot" can
trigger such a device reset, provided corresponding support has been
enabled in the HSS (Hart Software Services), the provider of SBI runtime
services on PolarFire SoC.

While this is a driver responsible for the reprogramming of an FPGA,
there is no dynamic discovery of devices involved, as runtime
reconfiguration is not possible due to the device reset requirements.
Therefore FPGA manager subsystem is not used by this driver and the FPGA
subsystem maintainers were unwilling to accept it there.

Signed-off-by: Conor Dooley <conor.dooley@microchip.com>

firmware: arm_scpi: Move power-domain driver to the pmdomain dir

To simplify with maintenance let's move the Arm SCPI power-domain driver
to the new pmdomain directory. Note this is different from and precedes
the new Arm SCMI protocol.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20231123120847.2825444-2-sudeep.holla@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

riscv, qemu_fw_cfg: Add support for RISC-V architecture

Qemu fw_cfg support was missing for RISC-V, which made it hard to do
proper vmcore dumps from qemu.

Add the missing RISC-V arch-defines.

You can now do vmcore dumps from qemu. Add "-device vmcoreinfo" to the
qemu command-line. From the qemu monitor:
(qemu) dump-guest-memory vmcore

The vmcore can now be used, e.g., with the "crash" utility.

Acked-by: "Michael S. Tsirkin" <mst@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Clément Léger <cleger@rivosinc.com>
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Message-Id: <20231012102852.234442-1-bjorn@kernel.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

firmware: qcom: move Qualcomm code into its own directory

We're getting more and more qcom specific .c files in drivers/firmware/
and about to get even more. Create a separate directory for Qualcomm
firmware drivers and move existing sources in there.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Elliot Berman <quic_eberman@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sc8280xp-lenovo-thinkpad-x13s
Link: https://lore.kernel.org/r/20231017092732.19983-2-brgl@bgdev.pl
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

firmware: qcom: qseecom: Add missing AUXILIARY_BUS dependency

The newly introduced QSEECOM driver fail to link if the system is built
without CONFIG_AUXILIARY_BUS, make sure it is selected.

Fixes: 00b1248606ba ("firmware: qcom_scm: Add support for Qualcomm Secure Execution Environment SCM interface")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/r/9f156fa6-e5aa-4cb2-ab2b-b67fd8fc4840%40infradead.org
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20230915-qseecom-auxiliary-fix-v1-1-38a46cfbfdb0@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

firmware: Add support for Qualcomm UEFI Secure Application

On platforms using the Qualcomm UEFI Secure Application (uefisecapp),
EFI variables cannot be accessed via the standard interface in EFI
runtime mode. The respective functions return EFI_UNSUPPORTED. On these
platforms, we instead need to talk to uefisecapp. This commit provides
support for this and registers the respective efivars operations to
access EFI variables from the kernel.

Communication with uefisecapp follows the Qualcomm QSEECOM / Secure OS
conventions via the respective SCM call interface. This is also the
reason why variable access works normally while boot services are
active. During this time, said SCM interface is managed by the boot
services. When calling ExitBootServices(), the ownership is transferred
to the kernel. Therefore, UEFI must not use that interface itself (as
multiple parties accessing this interface at the same time may lead to
complications) and cannot access variables for us.

Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230827211408.689076-4-luzmaximilian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

firmware: qcom_scm: Add support for Qualcomm Secure Execution Environment SCM interface

Add support for SCM calls to Secure OS and the Secure Execution
Environment (SEE) residing in the TrustZone (TZ) via the QSEECOM
interface. This allows communication with Secure/TZ applications, for
example 'uefisecapp' managing access to UEFI variables.

For better separation, make qcom_scm spin up a dedicated child
(platform) device in case QSEECOM support has been detected. The
corresponding driver for this device is then responsible for managing
any QSEECOM clients. Specifically, this driver attempts to automatically
detect known and supported applications, creating a client (auxiliary)
device for each one. The respective client/auxiliary driver is then
responsible for managing and communicating with the application.

While this patch introduces only a very basic interface without the more
advanced features (such as re-entrant and blocking SCM calls and
listeners/callbacks), this is enough to talk to the aforementioned
'uefisecapp'.

Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230827211408.689076-3-luzmaximilian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arch: Remove Itanium (IA-64) architecture

The Itanium architecture is obsolete, and an informal survey [0] reveals
that any residual use of Itanium hardware in production is mostly HP-UX
or OpenVMS based. The use of Linux on Itanium appears to be limited to
enthusiasts that occasionally boot a fresh Linux kernel to see whether
things are still working as intended, and perhaps to churn out some
distro packages that are rarely used in practice.

None of the original companies behind Itanium still produce or support
any hardware or software for the architecture, and it is listed as
'Orphaned' in the MAINTAINERS file, as apparently, none of the engineers
that contributed on behalf of those companies (nor anyone else, for that
matter) have been willing to support or maintain the architecture
upstream or even be responsible for applying the odd fix. The Intel
firmware team removed all IA-64 support from the Tianocore/EDK2
reference implementation of EFI in 2018. (Itanium is the original
architecture for which EFI was developed, and the way Linux supports it
deviates significantly from other architectures.) Some distros, such as
Debian and Gentoo, still maintain [unofficial] ia64 ports, but many have
dropped support years ago.

While the argument is being made [1] that there is a 'for the common
good' angle to being able to build and run existing projects such as the
Grid Community Toolkit [2] on Itanium for interoperability testing, the
fact remains that none of those projects are known to be deployed on
Linux/ia64, and very few people actually have access to such a system in
the first place. Even if there were ways imaginable in which Linux/ia64
could be put to good use today, what matters is whether anyone is
actually doing that, and this does not appear to be the case.

There are no emulators widely available, and so boot testing Itanium is
generally infeasible for ordinary contributors. GCC still supports IA-64
but its compile farm [3] no longer has any IA-64 machines. GLIBC would
like to get rid of IA-64 [4] too because it would permit some overdue
code cleanups. In summary, the benefits to the ecosystem of having IA-64
be part of it are mostly theoretical, whereas the maintenance overhead
of keeping it supported is real.

So let's rip off the band aid, and remove the IA-64 arch code entirely.
This follows the timeline proposed by the Debian/ia64 maintainer [5],
which removes support in a controlled manner, leaving IA-64 in a known
good state in the most recent LTS release. Other projects will follow
once the kernel support is removed.

[0] https://lore.kernel.org/all/CAMj1kXFCMh_578jniKpUtx_j8ByHnt=s7S+yQ+vGbKt9ud7+kQ@mail.gmail.com/
[1] https://lore.kernel.org/all/0075883c-7c51-00f5-2c2d-5119c1820410@web.de/
[2] https://gridcf.org/gct-docs/latest/index.html
[3] https://cfarm.tetaneutral.net/machines/list/
[4] https://lore.kernel.org/all/87bkiilpc4.fsf@mid.deneb.enyo.de/
[5] https://lore.kernel.org/all/ff58a3e76e5102c94bb5946d99187b358def688a.camel@physik.fu-berlin.de/

Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>

firmware: mediatek: Add adsp ipc protocol interface

Some of mediatek processors contain
the Tensilica HiFix DSP for audio processing.

The communication between Host CPU and DSP firmware is
taking place using a shared memory area for message passing.

ADSP IPC protocol offers (send/recv) interfaces using
mediatek-mailbox APIs.

We use two mbox channels to implement a request-reply protocol.

Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Signed-off-by: TingHan Shen <tinghan.shen@mediatek.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Reviewed-by: YC Hung <yc.hung@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220512082215.3018-2-tinghan.shen@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>

sysfb: Enable boot time VESA graphic mode selection

Since switch to simplefb/simpledrm VESA graphic mode selection with vga=
kernel parameter is no longer available with legacy BIOS.

The x86 realmode boot code enables the VESA graphic modes when option
FB_BOOT_VESA_SUPPORT is enabled.

This option is selected by vesafb but not simplefb/simpledrm.

To enable use of VESA modes with simplefb in legacy BIOS boot mode drop
dependency of BOOT_VESA_SUPPORT on FB, also drop the FB_ prefix. Select
the option from sysfb rather than the drivers that depend on it.

The BOOT_VESA_SUPPORT is not specific to framebuffer but rather to x86
platform, move it from fbdev to x86 Kconfig.

Fixes: e3263ab389a7 ("x86: provide platform-devices for boot-framebuffers")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/948c39940a4e99f5b43bdbcbe537faae71a43e1d.1645822213.git.msuchanek@suse.de

sysfb: Make config option dependencies explicit

efifb and vesafb requires sysfb implicitly but this is not stated in
Kconfig. Add the dependency.

With that all drivers that require sysfb depend on it so it can default
to disabled.

Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/a0fa41e9186653e4c41ad0a28259e5cdc71b1f66.1645822213.git.msuchanek@suse.de

ACPI: APEI: explicit init of HEST and GHES in apci_init()

From commit e147133a42cb ("ACPI / APEI: Make hest.c manage the estatus
memory pool") was merged, ghes_init() relies on acpi_hest_init() to manage
the estatus memory pool. On the other hand, ghes_init() relies on
sdei_init() to detect the SDEI version and (un)register events. The
dependencies are as follows:

ghes_init() => acpi_hest_init() => acpi_bus_init() => acpi_init()
ghes_init() => sdei_init()

HEST is not PCI-specific and initcall ordering is implicit and not
well-defined within a level.

Based on above, remove acpi_hest_init() from acpi_pci_root_init() and
convert ghes_init() and sdei_init() from initcalls to explicit calls in the
following order:

acpi_hest_init()
ghes_init()
sdei_init()

Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs

wm_adsp originally provided firmware loading on some audio DSP and was
implemented as an ASoC codec driver. However, the firmware loading now
covers a wider range of DSP cores and peripherals containing them,
beyond just audio. So it needs to be available to non-audio drivers. All
the core firmware loading support has been moved into a new driver
cs_dsp, leaving only the ASoC-specific parts in wm_adsp.

Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210913160057.103842-17-simont@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

qcom_scm: hide Kconfig symbol

Now that SCM can be a loadable module, we have to add another
dependency to avoid link failures when ipa or adreno-gpu are
built-in:

aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe':
ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available'

ld.lld: error: undefined symbol: qcom_scm_is_available
>>> referenced by adreno_gpu.c
>>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a

This can happen when CONFIG_ARCH_QCOM is disabled and we don't select
QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd
use a similar dependency here to what we have for QCOM_RPROC_COMMON,
but that causes dependency loops from other things selecting QCOM_SCM.

This appears to be an endless problem, so try something different this
time:

- CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on'
but that is simply selected by all of its users

- All the stubs in include/linux/qcom_scm.h can go away

- arm-smccc.h needs to provide a stub for __arm_smccc_smc() to
allow compile-testing QCOM_SCM on all architectures.

- To avoid a circular dependency chain involving RESET_CONTROLLER
and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement.
According to my testing this still builds fine, and the QCOM
platform selects this symbol already.

Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

firmware: qcom_scm: QCOM_SCM should depend on ARCH_QCOM

The Qualcomm Secure Channel Manager (SCM) is only present on Qualcomm
SoCs. All drivers using it select QCOM_SCM, and depend on ARCH_QCOM.
Until recently, QCOM_SCM was an invisible symbol, but this was changed
by adding loadable module support, exposing it to all ARM and ARM64
users. Hence add a dependency on ARCH_QCOM, to prevent asking the user
about this driver when configuring a kernel without Qualcomm SoC
support.

While at it, drop the dependency on ARM || ARM64, as that is implied by
HAVE_ARM_SMCCC.

Fixes: b42000e4b8741bf6 ("firmware: qcom_scm: Allow qcom_scm driver to be loadable as a permenent module")
Fixes: 2954a6f12f250890 ("firmware: qcom-scm: Fix QCOM_SCM configuration")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/5cda77085c07dc2e8d2195507b287457cb2f09e9.1629807831.git.geert+renesas@glider.be

firmware: arm_scmi: Make SCMI transports configurable

Add configuration options to be able to select which SCMI transports have
to be compiled into the SCMI stack.

Mailbox and SMC are by default enabled if their related dependencies are
satisfied.

While doing that move all SCMI related config options in their own
dedicated submenu.

Link: https://lore.kernel.org/r/20210803131024.40280-9-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

drivers/firmware: fix SYSFB depends to prevent build failures

The Generic System Framebuffers support is built when the COMPILE_TEST
option is enabled. But this wrongly assumes that all the architectures
declare a struct screen_info.

This is true for most architectures, but at least the following do not:
arc, m68k, microblaze, openrisc, parisc and s390.

By attempting to make this compile testeable on all architectures, it
leads to linking errors as reported by the kernel test robot for parisc:

All errors (new ones prefixed by >>):

hppa-linux-ld: drivers/firmware/sysfb.o: in function `sysfb_init':
(.init.text+0x24): undefined reference to `screen_info'
>> hppa-linux-ld: (.init.text+0x28): undefined reference to `screen_info'

To prevent these errors only allow sysfb to be built on systems that are
going to need it, which are x86 BIOS and EFI.

The EFI Kconfig symbol is used instead of (ARM || ARM64 || RISC) because
some of these architectures only declare a struct screen_info if EFI is
enabled. And also, because the SYSFB code is only used for EFI on these
architectures. For !EFI the "simple-framebuffer" device is registered by
OF when parsing the Device Tree Blob (if a DT node for this was defined).

Fixes: d391c5827107 ("drivers/firmware: move x86 Generic System Framebuffers support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727093015.1225107-1-javierm@redhat.com

drivers/firmware: consolidate EFI framebuffer setup for all arches

The register_gop_device() function registers an "efi-framebuffer" platform
device to match against the efifb driver, to have an early framebuffer for
EFI platforms.

But there is already support to do exactly the same by the Generic System
Framebuffers (sysfb) driver. This used to be only for X86 but it has been
moved to drivers/firmware and could be reused by other architectures.

Also, besides supporting registering an "efi-framebuffer", this driver can
register a "simple-framebuffer" allowing to use the siple{fb,drm} drivers
on non-X86 EFI platforms. For example, on aarch64 these drivers can only
be used with DT and doesn't have code to register a "simple-frambuffer"
platform device when booting with EFI.

For these reasons, let's remove the register_gop_device() duplicated code
and instead move the platform specific logic that's there to sysfb driver.

Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210625131359.1804394-1-javierm@redhat.com

drivers/firmware: move x86 Generic System Framebuffers support

The x86 architecture has generic support to register a system framebuffer
platform device. It either registers a "simple-framebuffer" if the config
option CONFIG_X86_SYSFB is enabled, or a legacy VGA/VBE/EFI FB device.

But the code is generic enough to be reused by other architectures and can
be moved out of the arch/x86 directory.

This will allow to also support the simple{fb,drm} drivers on non-x86 EFI
platforms, such as aarch64 where these drivers are only supported with DT.

Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210625130947.1803678-2-javierm@redhat.com

firmware: qcom_scm: Allow qcom_scm driver to be loadable as a permenent module

Allow the qcom_scm driver to be loadable as a permenent module.

This still uses the "depends on QCOM_SCM || !QCOM_SCM" bit to
ensure that drivers that call into the qcom_scm driver are
also built as modules. While not ideal in some cases its the
only safe way I can find to avoid build errors without having
those drivers select QCOM_SCM and have to force it on (as
QCOM_SCM=n can be valid for those drivers).

Reviving this now that Saravana's fw_devlink defaults to on,
which should avoid loading troubles seen before.

Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20210707045320.529186-1-john.stultz@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

firmware: arm_scmi: Add SMCCC discovery dependency in Kconfig

ARM_SCMI_PROTOCOL depends on either MAILBOX or HAVE_ARM_SMCCC_DISCOVERY,
not MAILBOX alone. Fix the depedency in Kconfig file and driver to
reflect the same.

Link: https://lore.kernel.org/r/20210521134055.24271-1-etienne.carriere@linaro.org
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
[sudeep.holla: Minor tweaks to subject and change log]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

firmware: arm_ffa: Add initial FFA bus support for device enumeration

The Arm FF for Armv8-A specification has concept of endpoints or
partitions. In the Normal world, a partition could be a VM when
the Virtualization extension is enabled or the kernel itself.

In order to handle multiple partitions, we can create a FFA device for
each such partition on a dedicated FFA bus. Similarly, different drivers
requiring FFA transport can be registered on the same bus. We can match
the device and drivers using UUID. This is mostly for the in-kernel
users with FFA drivers.

Link: https://lore.kernel.org/r/20210521151033.181846-2-sudeep.holla@arm.com
Tested-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

firmware: qcom-scm: Fix QCOM_SCM configuration

When CONFIG_QCOM_SCM is y and CONFIG_HAVE_ARM_SMCCC
is not set, compiling errors are encountered as follows:

drivers/firmware/qcom_scm-smc.o: In function `__scm_smc_do_quirk':
qcom_scm-smc.c:(.text+0x36): undefined reference to `__arm_smccc_smc'
drivers/firmware/qcom_scm-legacy.o: In function `scm_legacy_call':
qcom_scm-legacy.c:(.text+0xe2): undefined reference to `__arm_smccc_smc'
drivers/firmware/qcom_scm-legacy.o: In function `scm_legacy_call_atomic':
qcom_scm-legacy.c:(.text+0x1f0): undefined reference to `__arm_smccc_smc'

Note that __arm_smccc_smc is defined when HAVE_ARM_SMCCC is y.
So add dependency on HAVE_ARM_SMCCC in QCOM_SCM configuration.

Fixes: 916f743da354 ("firmware: qcom: scm: Move the scm driver to drivers/firmware")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: He Ying <heying24@huawei.com>
Link: https://lore.kernel.org/r/20210406094200.60952-1-heying24@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: stratix10-svc: build only on 64-bit ARM

The Stratix10 service layer and RCU drivers are useful only on
Stratix10, so on ARMv8. Compile testing the RCU driver on 32-bit ARM
fails:

drivers/firmware/stratix10-rsu.c: In function 'rsu_status_callback':
include/linux/compiler_types.h:320:38: error: call to '__compiletime_assert_179'
declared with attribute error: FIELD_GET: type of reg too small for mask
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
...
drivers/firmware/stratix10-rsu.c:96:26: note: in expansion of macro 'FIELD_GET'
priv->status.version = FIELD_GET(RSU_VERSION_MASK,

Fixes: 4483397b0353 ("ARM: socfpga: drop ARCH_SOCFPGA")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Richard Gong <richard.gong@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2: add Fixes tag

arm64: socfpga: merge Agilex and N5X into ARCH_INTEL_SOCFPGA

Agilex, N5X and Stratix 10 share all quite similar arm64 hard cores and
SoC-part. Up to a point that N5X uses the same DTSI as Agilex. From
the Linux kernel point of view these are flavors of the same
architecture so there is no need for three top-level arm64
architectures. Simplify this by merging all three architectures into
ARCH_INTEL_SOCFPGA and dropping the other ARCH* arm64 Kconfig entries.

The side effect is that the INTEL_STRATIX10_SERVICE will now be
available for both 32-bit and 64-bit Intel SoCFPGA, even though it is
used only for 64-bit.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

firmware: fix a spelling mistake "managament" -> "management" in Kconfig

There is a spelling mistake in the Kconfig help text. Fix it.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201204192250.1151316-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "firmware: QCOM_SCM: Allow qcom_scm driver to be loadable as a permenent module"

This reverts commit d0511b5496c03cdbcda55a9b57c32cdd751920ed.

After some time it was noticed that the Tegra186 among others
were experiencing problems when making this into a module.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

firmware: QCOM_SCM: Allow qcom_scm driver to be loadable as a permenent module

Allow the qcom_scm driver to be loadable as a permenent module.

This still uses the "depends on QCOM_SCM || !QCOM_SCM" bit to
ensure that drivers that call into the qcom_scm driver are
also built as modules. While not ideal in some cases its the
only safe way I can find to avoid build errors without having
those drivers select QCOM_SCM and have to force it on (as
QCOM_SCM=n can be valid for those drivers).

Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-gpio@vger.kernel.org
Link: https://lore.kernel.org/r/20201106042710.55979-3-john.stultz@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

fw_cfg: Add support for parisc architecture

Signed-off-by: Helge Deller <deller@gmx.de>

firmware: arm_scmi: Enable building as a single module

Now, with all the plumbing in place to enable building scmi as a module
instead of built-in modules, let us enable the same.

Link: https://lore.kernel.org/r/20200907195046.56615-5-sudeep.holla@arm.com
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Revert "USB: pci-quirks: Add Raspberry Pi 4 quirk"

This reverts commit c65822fef4adc0ba40c37a47337376ce75f7a7bc.

The initialization of Raspberry Pi 4's USB chip is now handled through a
reset controller. No need to directly call the firmware routine through a
PCI quirk.

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-7-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: smccc: Add HAVE_ARM_SMCCC_DISCOVERY to identify SMCCC v1.1 and above

SMCCC v1.0 lacked discoverability of version and features. To accelerate
adoption of few mitigations and protect systems more rapidly from various
vulnerability, PSCI v1.0 was updated to add SMCCC discovery mechanism
though the PSCI firmware implementation of PSCI_FEATURES(SMCCC_VERSION)
which returns success on firmware compliant to SMCCC v1.1 and above.

This inturn makes SMCCC v1.1 and above dependent on ARM_PSCI_FW for
backward compatibility. Let us introduce a new hidden config for the
same to build more features on top of SMCCC v1.1 and above.

While at it, also sort alphabetically the psci entry.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Etienne Carriere <etienne.carriere@st.com>
Reviewed-by: Etienne Carriere <etienne.carriere@st.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20200518091222.27467-2-sudeep.holla@arm.com
Signed-off-by: Will Deacon <will@kernel.org>

USB: pci-quirks: Add Raspberry Pi 4 quirk

On the Raspberry Pi 4, after a PCI reset, VL805's firmware may either be
loaded directly from an EEPROM or, if not present, by the SoC's
VideoCore. Inform VideoCore that VL805 was just reset.

Also, as this creates a dependency between USB_PCI and VideoCore's
firmware interface, and since USB_PCI can't be set as a module neither
this can. Reflect that on the firmware interface Kconfg.

Link: https://lore.kernel.org/r/20200505161318.26200-5-nsaenzjulienne@suse.de
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>

firmware: intel_stratix10_service: add depend on agilex

Add depend on Agilex for Intel Agilex SoC platform.

Signed-off-by: Richard Gong <richard.gong@intel.com>
Acked-by: Moritz Fischer <mdf@kernel.org>
Link: https://lore.kernel.org/r/1583428346-13307-3-git-send-email-richard.gong@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: qcom_scm: Dynamically support SMCCC and legacy conventions

Dynamically support SMCCCC and legacy conventions by detecting which
convention to use at runtime. qcom_scm_call_atomic and qcom_scm_call can
then be moved in qcom_scm.c and use underlying convention backend as
appropriate. Thus, rename qcom_scm-64,-32 to reflect that they are
backends for -smc and -legacy, respectively.

Also add support for making SCM calls earlier than when SCM driver
probes to support use cases such as qcom_scm_set_cold_boot_addr. Support
is added by lazily initializing the convention and guarding the query
with a spin lock. The limitation of these early SCM calls is that they
cannot use DMA, as in the case of >4 arguments for SMC convention and
any non-atomic call for legacy convention.

Tested-by: Brian Masney <masneyb@onstation.org> # arm32
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Elliot Berman <eberman@codeaurora.org>
Link: https://lore.kernel.org/r/1578431066-19600-18-git-send-email-eberman@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

firmware: Add Turris Mox rWTM firmware driver

This adds a driver to communicate with the firmware running on the
secure processor of the Turris Mox router, enabling the kernel to
retrieve true random numbers from the Entropy Bit Generator and to read
some information burned into eFuses when device was manufactured:

and to
sign messages with the ECDSA private key burned into each Turris Mox
device when manufacturing.

This also adds support to read other information burned into eFuses:
- serial number
- board version
- MAC addresses
- RAM size
- ECDSA public key (this is not read directly from eFuses, rather it
is computed by the firmware as pair to the burned private key)

The source code of the firmware is open source and can be found at
https://gitlab.labs.nic.cz/turris/mox-boot-builder/tree/master/wtmi

The firmware is also able to, on demand, sign messages with the burned
ECDSA private key, but since Linux's akcipher API is not yet stable
(and therefore not exposed to userspace via netlink), this functionality
is not supported yet.

Link: https://lore.kernel.org/r/20190822014318.19478-3-marek.behun@nic.cz
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

firmware: add Intel Stratix10 remote system update driver

The Intel Remote System Update (RSU) driver exposes interfaces access
through the Intel Service Layer to user space via sysfs interface.
The RSU interfaces report and control some of the optional RSU features
on Intel Stratix 10 SoC.

The RSU feature provides a way for customers to update the boot
configuration of a Intel Stratix 10 SoC device with significantly reduced
risk of corrupting the bitstream storage and bricking the system.

Signed-off-by: Richard Gong <richard.gong@intel.com>
Reviewed-by: Alan Tull <atull@kernel.org>
Link: https://lore.kernel.org/r/1567516701-26026-3-git-send-email-richard.gong@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iscsi_ibft: make ISCSI_IBFT dependson ACPI instead of ISCSI_IBFT_FIND

iscsi_ibft can use ACPI to find the iBFT entry during bootup,
currently, ISCSI_IBFT depends on ISCSI_IBFT_FIND which is
a X86 legacy way to find the iBFT by searching through the
low memory. This patch changes the dependency so that other
arch like ARM64 can use ISCSI_IBFT as long as the arch supports
ACPI.

ibft_init() needs to use the global variable ibft_addr declared
in iscsi_ibft_find.c. A #ifndef CONFIG_ISCSI_IBFT_FIND is needed
to declare the variable if CONFIG_ISCSI_IBFT_FIND is not selected.
Moving ibft_addr into the iscsi_ibft.c does not work because if
ISCSI_IBFT is selected as a module, the arch/x86/kernel/setup.c won't
be able to find the variable at compile time.

Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

firmware: trusted_foundations: add ARMv7 dependency

The "+sec" extension is invalid for older ARM architectures, but
the code can now be built on any ARM configuration:

/tmp/trusted_foundations-2d0882.s: Assembler messages:
/tmp/trusted_foundations-2d0882.s:194: Error: architectural extension `sec' is not allowed for the current base architecture
/tmp/trusted_foundations-2d0882.s:201: Error: selected processor does not support `smc #0' in ARM mode
/tmp/trusted_foundations-2d0882.s:213: Error: architectural extension `sec' is not allowed for the current base architecture
/tmp/trusted_foundations-2d0882.s:220: Error: selected processor does not support `smc #0' in ARM mode

Add a dependency on ARMv7 for the build.

Fixes: 4cb5d9eca143 ("firmware: Move Trusted Foundations support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

docs: kbuild: convert docs to ReST and rename to *.rst

The kbuild documentation clearly shows that the documents
there are written at different times: some use markdown,
some use their own peculiar logic to split sections.

Convert everything to ReST without affecting too much
the author's style and avoiding adding uneeded markups.

The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.

At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

treewide: Add SPDX license identifier - Makefile/Kconfig

Add SPDX license identifiers to all Make/Kconfig files which:

- Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: Move Trusted Foundations support

Move the Trusted Foundations support out of arch/arm/firmware and into
drivers/firmware where most other firmware support implementations are
located.

Signed-off-by: Thierry Reding <treding@nvidia.com>

drivers: firmware: psci: Move psci to separate directory

Some following changes extends the PSCI driver with some additional
files. Avoid to continue cluttering the toplevel firmware directory
and first move the PSCI files into a PSCI sub-directory.

Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

firmware: intel_stratix10_service: remove COMPILE_TEST

This does not build yet ...

Cc: Richard Gong <richard.gong@intel.com>
Fixes: 095ff29d2b88 ("firmware: intel_stratix10_service: add hardware dependency")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: intel_stratix10_service: add hardware dependency

Add a Kconfig dependency to ensure Intel Stratix10 service layer driver
can be built only on the platform that supports it.

Signed-off-by: Richard Gong <richard.gong@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: add Intel Stratix10 service layer driver

Some features of the Intel Stratix10 SoC require a level of privilege
higher than the kernel is granted. Such secure features include
FPGA programming. In terms of the ARMv8 architecture, the kernel runs
at Exception Level 1 (EL1), access to the features requires
Exception Level 3 (EL3).

The Intel Stratix10 SoC service layer provides an in kernel API for
drivers to request access to the secure features. The requests are queued
and processed one by one. ARM’s SMCCC is used to pass the execution
of the requests on to a secure monitor (EL3).

The header file stratix10-sve-client.h defines the interface between
service providers (FPGA manager is one of them) and service layer.

The header file stratix10-smc.h defines the secure monitor call (SMC)
message protocols used for service layer driver in normal world
(EL1) to communicate with secure monitor SW in secure monitor exception
level 3 (EL3).

Signed-off-by: Richard Gong <richard.gong@intel.com>
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: imx: add SCU firmware driver support

The System Controller Firmware (SCFW) is a low-level system function
which runs on a dedicated Cortex-M core to provide power, clock, and
resource management. It exists on some i.MX8 processors. e.g. i.MX8QM
(QM, QP), and i.MX8QX (QXP, DX).

This patch implements the SCU firmware IPC function and the common
message sending API sc_call_rpc.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

firmware: dcdbas: Move dcdbas to drivers/platform/x86

Move dcdbas to the more appropriate directory drivers/platform/x86.

Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

firmware: dell_rbu: Move dell_rbu to drivers/platform/x86

Move dell_rbu to the more appropriate directory drivers/platform/x86.

Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

firmware: xilinx: Add Zynqmp firmware driver

This patch is adding communication layer with firmware.
Firmware driver provides an interface to firmware APIs.
Interface APIs can be used by any driver to communicate to
PMUFW(Platform Management Unit). All requests go through ATF.

Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

firmware: arm_scmi: add device power domain support using genpd

This patch hooks up the support for device power domain provided by
SCMI using the Linux generic power domain infrastructure.

Cc: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

firmware: arm_scmi: add basic driver infrastructure for SCMI

The SCMI is intended to allow OSPM to manage various functions that are
provided by the hardware platform it is running on, including power and
performance functions. SCMI provides two levels of abstraction, protocols
and transports. Protocols define individual groups of system control and
management messages. A protocol specification describes the messages
that it supports. Transports describe the method by which protocol
messages are communicated between agents and the platform.

This patch adds basic infrastructure to manage the message allocation,
initialisation, packing/unpacking and shared memory management.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

psci: add CPU_IDLE dependency

I ran into a build error for the psci_checker:

drivers/firmware/psci_checker.o: In function `psci_checker':
psci_checker.c:(.init.text+0x528): undefined reference to `cpuidle_devices'

As far as I can tell, this is simply a very rare combination of options,
but the problem has existed since the code was initially added.
Adding a Kconfig dependency makes it build properly.

Fixes: ea8b1c4a6019 ("drivers: psci: PSCI checker module")
Acked-by: Kevin Brodsky <kevin.brodsky@arm.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

firmware: arm_sdei: Add driver for Software Delegated Exceptions

The Software Delegated Exception Interface (SDEI) is an ARM standard
for registering callbacks from the platform firmware into the OS.
This is typically used to implement firmware notifications (such as
firmware-first RAS) or promote an IRQ that has been promoted to a
firmware-assisted NMI.

Add the code for detecting the SDEI version and the framework for
registering and unregistering events. Subsequent patches will add the
arch-specific backend code and the necessary power management hooks.

Only shared events are supported, power management, private events and
discovery for ACPI systems will be added by later patches.

Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

firmware: qcom: scm: Expose download-mode control

In order to aid post-mortem debugging the Qualcomm platforms provide a
"memory download mode", where the boot loader will provide an interface
for custom tools to "download" the content of RAM to a host machine.

The mode is triggered by writing a magic value somewhere in RAM, that is
read in the boot code path after a warm-restart. Two mechanism for
setting this magic value are supported in modern platforms; a direct SCM
call to enable the mode or through a secure io write of a magic value.

In order for a normal reboot not to trigger "download mode" the magic
must be cleared during a clean reboot.

Download mode has to be enabled by including qcom_scm.download_mode=1 on
the command line.

Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

firmware: arm_scpi: Add hardware dependencies

With a name like that, I assume that the ARM SCPI protocol is only
useful on the ARM architectures.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Jon Medhurst (Tixy) <tixy@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

drivers: psci: PSCI checker module

On arm and arm64, PSCI is one of the possible firmware interfaces
used for power management. This includes both turning CPUs on and off,
and suspending them (entering idle states).

This patch adds a PSCI checker module that enables basic testing of
PSCI operations during startup. There are two main tests: CPU
hotplugging and suspending.

In the hotplug tests, the hotplug API is used to turn off and on again
all CPUs in the system, and then all CPUs in each cluster, checking
the consistency of the return codes.

In the suspend tests, a high-priority thread is created on each core
and uses low-level cpuidle functionalities to enter suspend, in all
the possible states and multiple times. This should allow a maximum
number of CPUs to enter the same sleep state at the same or slightly
different time.

In essence, the suspend tests use a principle similar to that of the
intel_powerclamp driver (drivers/thermal/intel_powerclamp.c), but the
threads are only kept for the duration of the test (they are already
gone when userspace is started) and it does not require to stop/start
the tick.

While in theory power management PSCI functions (CPU_{ON,OFF,SUSPEND})
could be directly called, this proved too difficult as it would imply
the duplication of all the logic used by the kernel to allow for a
clean shutdown/bringup/suspend of the CPU (the deepest sleep states
implying potentially the shutdown of the CPU).

Note that this file cannot be compiled as a loadable module, since it
uses a number of non-exported identifiers (essentially for
PSCI-specific checks and direct use of cpuidle) and relies on the
absence of userspace to avoid races when calling hotplug and cpuidle
functions.

For now at least, CONFIG_PSCI_CHECKER is mutually exclusive with
CONFIG_TORTURE_TEST, because torture tests may also use hotplug and
cause false positives in the hotplug tests.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> [torture test config]
Signed-off-by: Kevin Brodsky <kevin.brodsky@arm.com>
[lpieralisi: added cpuidle locking, reworded commit log/kconfig entry]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

firmware: tegra: Add IVC library

The Inter-VM communication (IVC) is a communication protocol which is
designed for interprocessor communication (IPC) or the communication
between the hypervisor and the virtual machine with a guest OS.

Message channels are used to communicate between processors. They are
backed by DRAM or SRAM, so care must be taken to maintain coherence of
data.

The IVC library maintains memory-based descriptors for the transmission
and reception channels as well as the data coherence of the counter and
payload. Clients, such as the driver for the BPMP firmware, can use the
library to exchange messages with remote processors.

Based on work by Peter Newman <pnewman@nvidia.com> and Joseph Lo
<josephl@nvidia.com>.

Signed-off-by: Thierry Reding <treding@nvidia.com>

firmware: Add basic support for TI System Control Interface (TI-SCI) protocol

Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used in Texas Instrument's System on Chip (SoC) such as those
in keystone family K2G SoC to communicate between various compute
processors with a central system controller entity.

TI-SCI message protocol provides support for management of various
hardware entities within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.

We introduce the basic registration and query capability for the
driver protocol as part of this change. Subsequent patches add in
functionality specific to the TI-SCI features.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

firmware: Amlogic: Add secure monitor driver

Introduce a driver to provide calls into secure monitor mode.

In the Amlogic SoCs these calls are used for multiple reasons: access to
NVMEM, set USB boot, enable JTAG, etc...

Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
[khilman: add in SZ_4K cleanup]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

firmware: scpi: add CONFIG_OF dependency

We get a harmless warning if the ARM_SCPI_POWER_DOMAIN driver is enabled
without CONFIG_OF during compile testing:

warning: (ARM_SCPI_POWER_DOMAIN) selects PM_GENERIC_DOMAINS_OF which has unmet direct dependencies (PM_GENERIC_DOMAINS && OF)

There is no need to select PM_GENERIC_DOMAINS_OF if OF is set, so we can
replace the 'select' with a dependency.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 8bec4337ad40 ("firmware: scpi: add device power domain support using genpd")
Acked-by: Sudeep Holla <sudeep.holla@arm.com>

firmware: qcom: scm: Expose PAS command 10 as reset-controller

PAS command 10 is used to assert and deassert the MSS reset via
TrustZone, expose this as a reset-controller to mimic the direct
access case.

Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

firmware: scpi: add device power domain support using genpd

This patch hooks up the support for device power domain provided by
SCPI using the Linux generic power domain infrastructure.

Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Jon Medhurst <tixy@linaro.org>
Reviewed-by: Jon Medhurst <tixy@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

firmware: arm_scpi: make it depend on MAILBOX instead of ARM_MHU

ARM_SCPI_PROTOCOL can be used with any mailbox and not just ARM MHU
mailbox controller. This patch drops it's dependency on ARM_MHU and
make it depend on just mailbox framework.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

firmware: qemu config needs I/O ports

Not all machines have PCI style I/O port memory, or they do not allow
mapping it using the ioport_map() function, whcih results in a
build error with the newly added qemu firmware code:

drivers/firmware/built-in.o: In function `fw_cfg_io_cleanup':
qemu_fw_cfg.c:(.text+0x144): undefined reference to `ioport_unmap'
drivers/firmware/built-in.o: In function `fw_cfg_sysfs_probe':
qemu_fw_cfg.c:(.text+0xb18): undefined reference to `ioport_map'

This adds a Kconfig dependency to ensure the driver can only
be built on platforms that support it.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 75f3e8e47f38 ("firmware: introduce sysfs driver for QEMU's fw_cfg device")
Acked-by: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: introduce sysfs driver for QEMU's fw_cfg device

Make fw_cfg entries of type "file" available via sysfs. Entries
are listed under /sys/firmware/qemu_fw_cfg/by_key, in folders
named after each entry's selector key. Filename, selector value,
and size read-only attributes are included for each entry. Also,
a "raw" attribute allows retrieval of the full binary content of
each entry.

The fw_cfg device can be instantiated automatically from ACPI or
the Device Tree, or manually by using a kernel module (or command
line) parameter, with a syntax outlined in the documentation file.

Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: 8478/2: arm/arm64: add arm-smccc

Adds helpers to do SMC and HVC based on ARM SMC Calling Convention.
CONFIG_HAVE_ARM_SMCCC is enabled for architectures that may support the
SMC or HVC instruction. It's the responsibility of the caller to know if
the SMC instruction is supported by the platform.

This patch doesn't provide an implementation of the declared functions.
Later patches will bring in implementations and set
CONFIG_HAVE_ARM_SMCCC for ARM and ARM64 respectively.

Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

ARM: bcm2835: Add the Raspberry Pi firmware driver

This gives us a function for making mailbox property channel requests
of the firmware, which is most notable in that it will let us get and
set clock rates.

Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>

firmware: add support for ARM System Control and Power Interface(SCPI) protocol

This patch adds support for System Control and Power Interface (SCPI)
Message Protocol used between the Application Cores(AP) and the System
Control Processor(SCP). The MHU peripheral provides a mechanism for
inter-processor communication between SCP's M3 processor and AP.

SCP offers control and management of the core/cluster power states,
various power domain DVFS including the core/cluster, certain system
clocks configuration, thermal sensors and many others.

This protocol driver provides interface for all the client drivers using
SCPI to make use of the features offered by the SCP.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Jon Medhurst (Tixy) <tixy@linaro.org>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

firmware: qcom: scm: Add function stubs for ARM64

This patch adds stubs for the SCM functions exposed in the QCOM SCM API.

Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>

arm64: psci: factor invocation code to drivers

To enable sharing with arm, move the core PSCI framework code to
drivers/firmware. This results in a minor gain in lines of code, but
this will quickly be amortised by the removal of code currently
duplicated in arch/arm.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/

After Broadcom switched from MIPS to ARM for their home routers we need
to have NVRAM driver in some common place (not arch/mips/). As explained
in Kconfig, this driver is responsible for parsing SoC configuration
data that is passed to the kernel in flash from the bootloader firmware
called "CFE".

We were thinking about putting it in bus directory, however there are
two possible buses for MIPS: drivers/ssb/ and drivers/bcma/. So this
won't fit there and this is why I would like to move this driver to the
drivers/firmware/.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mike Waychison <mikew@google.com>
Cc: Roy Franz <roy.franz@linaro.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/10544/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

firmware: qcom: scm: Move the scm driver to drivers/firmware

Architectural changes in the ARM Linux kernel tree mandate the eventual
removal of the mach-* directories. Move the scm driver to
drivers/firmware and the scm header to include/linux to support that
removal.

Signed-off-by: Kumar Gala <galak@codeaurora.org>

firmware/dmi_scan: generalize for use by other archs

This patch makes a couple of changes to the SMBIOS/DMI scanning
code so it can be used on other archs (such as ARM and arm64):
(a) wrap the calls to ioremap()/iounmap(), this allows the use of a
flavor of ioremap() more suitable for random unaligned access;
(b) allow the non-EFI fallback probe into hardcoded physical address
0xF0000 to be disabled.

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module

To avoid build problems and breaking dependencies between ACPI header
files, <acpi/acpi.h> should not be included directly by code outside
of the ACPI core subsystem, but this is done by the ACPI iSCSI
Boot Firmware code.

The iBFT specification doesn't mention whether or not it can appear
on a non-ACPI platform, but is says that ACPI 3.0b defines the
mechanism. The current CONFIG_ISCSI_IBFT_FIND code doesn't use the
ACPI tables API to locate the table, so it doesn't rely on CONFIG_ACPI
directly.

However, since iBFT is is an ACPI-based mechanism (please refer to
the documentation link below for more information), it should be
correct to make CONFIG_ISCSI_IBFT_FIND depend on CONFIG_ACPI (even
though the table location can be implemented without using ACPI
tables API).

After that change, include/linux/iscsi_ibft.h can be modified to
include <linux/acpi.h> instead of <acpi/acpi.h> as appropriate.

References: http://www.microsoft.com/whdc/system/platform/firmware/ibft.mspx
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Peter Jones <pjones@redhat.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

dell_rbu: Select CONFIG_FW_LOADER_USER_HELPER explicitly

The usermode helper is mandatory for this driver.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

efivars: Move pstore code into the new EFI directory

efivars.c has grown far too large and needs to be divided up. Create a
new directory and move the persistence storage code to efi-pstore.c now
that it uses the new efivar API. This helps us to greatly reduce the
size of efivars.c and paves the way for moving other code out of
efivars.c.

Note that because CONFIG_EFI_VARS can be built as a module efi-pstore
must also include support for building as a module.

Reviewed-by: Tom Gundersen <teg@jklm.no>
Tested-by: Tom Gundersen <teg@jklm.no>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>

Move utf16 functions to kernel core and rename

We want to be able to use the utf16 functions that are currently present
in the EFI variables code in platform-specific code as well. Move them to
the kernel core, and in the process rename them to accurately describe what
they do - they don't handle UTF16, only UCS2.

Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>

efivars: Add module parameter to disable use as a pstore backend

We know that with some firmware implementations writing too much data to
UEFI variables can lead to bricking machines. Recent changes attempt to
address this issue, but for some it may still be prudent to avoid
writing large amounts of data until the solution has been proven on a
wide variety of hardware.

Crash dumps or other data from pstore can potentially be a large data
source. Add a pstore_module parameter to efivars to allow disabling its
use as a backend for pstore. Also add a config option,
CONFIG_EFI_VARS_PSTORE_DEFAULT_DISABLE, to allow setting the default
value of this paramter to true (i.e. disabled by default).

Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>

efivars: Allow disabling use as a pstore backend

Add a new option, CONFIG_EFI_VARS_PSTORE, which can be set to N to
avoid using efivars as a backend to pstore, as some users may want to
compile out the code completely.

Set the default to Y to maintain backwards compatability, since this
feature has always been enabled until now.

Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>

ASoC: Move SigmaDSP firmware loader to ASoC

It has been pointed out previously, that the firmware subsystem is not the right
place for the SigmaDSP firmware loader. Furthermore the SigmaDSP is currently
only used in audio products and we are aiming for better integration into the
ASoC framework in the future, with support for ALSA controls for firmware
parameters and support dynamic power management as well. So the natural choice
for the SigmaDSP firmware loader is the ASoC subsystem.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

driver: Google EFI SMI

The "gsmi" driver bridges userland with firmware specific routines for
accessing hardware.

Currently, this driver only supports NVRAM and eventlog information.
Deprecated functions have been removed from the driver, though their
op-codes are left in place so that they are not re-used.

This driver works by trampolining into the firmware via the smi_command
outlined in the FADT table. Three protocols are used due to various
limitations over time, but all are included herein.

This driver should only ever load on Google boards, identified by either
a "Google, Inc." board vendor string in DMI, or "GOOGLE" in the OEM
strings of the FADT ACPI table. This logic happens in
gsmi_system_valid().

Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Aaron Durbin <adurbin@google.com>
Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

sigma-firmware: loader for Analog Devices' SigmaStudio

Analog Devices' SigmaStudio can produce firmware blobs for devices with
these DSPs embedded (like some audio codecs). Allow these device drivers
to easily parse and load them.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

firmware: Basic dmi-sysfs support

Introduce a new module "dmi-sysfs" that exports the broken out entries
of the DMI table through sysfs.

Entries are enumerated via dmi_walk() on module load, and are populated
as kobjects rooted at /sys/firmware/dmi/entries.

Entries are named "<type>-<instance>", where:
<type> : is the type of the entry, and
<instance> : is the ordinal count within the DMI table of that
entry type. This instance is used in lieu the DMI
entry's handle as no assurances are made by the kernel
that handles are unique.

All entries export the following attributes:
length : The length of the formatted portion of the entry
handle : The handle given to this entry by the firmware
raw : The raw bytes of the entire entry, including the
formatted portion, the unformatted (strings) portion,
and the two terminating nul characters.
type : The DMI entry type
instance : The ordinal instance of this entry given its type.
position : The position ordinal of the entry within the table in
its entirety.

Entries in dmi-sysfs are kobject backed members called "struct
dmi_sysfs_entry" and belong to dmi_kset. They are threaded through
entry_list (protected by entry_list_lock) so that we can find them at
cleanup time.

Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT

The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.

This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).

Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.

Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Update broken web addresses in the kernel.

The patch below updates broken web addresses in the kernel

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

ibft: fix kconfig dependencies

Fix kconfig dependency warning to satisfy dependencies:

warning: (BE2ISCSI && SCSI_LOWLEVEL && PCI && SCSI && NET || ISCSI_IBFT && ISCSI_IBFT_FIND && SCSI) selects ISCSI_BOOT_SYSFS which has unmet direct dependencies (SCSI_LOWLEVEL && SCSI)

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>

firmware: ibft depends on SCSI

Prevent build errors when SCSI is not enabled:

iscsi_ibft.c:(.init.text+0x548d): undefined reference to `iscsi_boot_create_initiator'
iscsi_ibft.c:(.init.text+0x54a9): undefined reference to `iscsi_boot_create_ethernet'
iscsi_ibft.c:(.init.text+0x54c5): undefined reference to `iscsi_boot_create_target'
iscsi_ibft.c:(.init.text+0x55ff): undefined reference to `iscsi_boot_destroy_kset'
iscsi_ibft.c:(.init.text+0x561e): undefined reference to `iscsi_boot_create_kset'
iscsi_ibft.c:(.exit.text+0xe2c): undefined reference to `iscsi_boot_destroy_kset'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>

[SCSI] iscsi boot: mv iscsi_boot_sysfs to drivers/scsi

iscsi_boot_sysfs does not depend on firmware. Any iscsi driver
can use it. This patch moves iscsi_boot_sysfs to the scsi
dir, so that it can be used on any arch with any driver.

Signed-off-by: Mike Christie <mchristi@redhat.com>
Acked-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

ibft: convert iscsi_ibft module to iscsi boot lib

This patch just converts the iscsi_ibft module to the
iscsi boot sysfs lib module.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Peter Jones <pjones@redhat.com>

ibft: separate ibft parsing from sysfs interface

Not all iscsi drivers support ibft. For drivers like be2iscsi
that do not but are bootable through a vendor firmware specific
format/process this patch moves the sysfs interface from the ibft code
to a lib module. This then allows userspace tools to search for iscsi boot
info in a common place and in a common format.

ibft iscsi boot info is exported in the same place as it was
before: /sys/firmware/ibft.

vendor/fw boot info gets export in /sys/firmware/iscsi_bootX, where X is the
scsi host number of the HBA. Underneath these parent dirs, the
target, ethernet, and initiator dirs are the same as they were before.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Peter Jones <pjones@redhat.com>

firmware: only allow EDD on x86

Rather than have the EDD depend on !ia64 (and assuming that only ia64,
x86, x86_64 will be including this Kconfig), have EDD depend on the only
arches which can support this code. This should allow all other arches to
cleanly include the firmware Kconfig.

Also simplify the x86 string used by FIRMWARE_MEMMAP to match EDD.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sysfs: add /sys/firmware/memmap

This patch adds /sys/firmware/memmap interface that represents the BIOS
(or Firmware) provided memory map. The tree looks like:

/sys/firmware/memmap/0/start (hex number)
end (hex number)
type (string)
... /1/start
end
type

With the following shell snippet one can print the memory map in the same form
the kernel prints itself when booting on x86 (the E820 map).

--------- 8< --------------------------
#!/bin/sh
cd /sys/firmware/memmap
for dir in * ; do
start=$(cat $dir/start)
end=$(cat $dir/end)
type=$(cat $dir/type)
printf "%016x-%016x (%s)\n" $start $[ $end +1] "$type"
done
--------- >8 --------------------------

That patch only provides the needed interface:

1. The sysfs interface.
2. The structure and enumeration definition.
3. The function firmware_map_add() and firmware_map_add_early()
that should be called from architecture code (E820/EFI, for
example) to add the contents to the interface.

If the kernel is compiled without CONFIG_FIRMWARE_MEMMAP, the interface does
nothing without cluttering the architecture-specific code with #ifdef's.

The purpose of the new interface is kexec: While /proc/iomem represents
the *used* memory map (e.g. modified via kernel parameters like 'memmap'
and 'mem'), the /sys/firmware/memmap tree represents the unmodified memory
map provided via the firmware. So kexec can:

- use the original memory map for rebooting,
- use the /proc/iomem for setting up the ELF core headers for kdump
case that should only represent the memory of the system.

The patch has been tested on i386 and x86_64.

Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Greg KH <gregkh@suse.de>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: kexec@lists.infradead.org
Cc: yhlu.kernel@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>

edd: add default mode CONFIG_EDD_OFF=n, override with edd={on,off}

Add a kernel parameter option to 'edd' to enable/disable BIOS Enhanced Disk
Drive Services. CONFIG_EDD_OFF disables EDD while still compiling EDD into
the kernel. Default behavior can be forced using 'edd=on' or 'edd=off' as
a kernel parameter.

[akpm@linux-foundation.org: fix kernel-parameters.txt]
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Firmware: add iSCSI iBFT Support

Add /sysfs/firmware/ibft/[initiator|targetX|ethernetX] directories along with
text properties which export the the iSCSI Boot Firmware Table (iBFT)
structure.

What is iSCSI Boot Firmware Table? It is a mechanism for the iSCSI tools to
extract from the machine NICs the iSCSI connection information so that they
can automagically mount the iSCSI share/target. Currently the iSCSI
information is hard-coded in the initrd. The /sysfs entries are read-only
one-name-and-value fields.

The usual set of data exposed is:

# for a in `find /sys/firmware/ibft/ -type f -print`; do echo -n "$a: "; cat $a; done
/sys/firmware/ibft/target0/target-name: iqn.2007.com.intel-sbx44:storage-10gb
/sys/firmware/ibft/target0/nic-assoc: 0
/sys/firmware/ibft/target0/chap-type: 0
/sys/firmware/ibft/target0/lun: 00000000
/sys/firmware/ibft/target0/port: 3260
/sys/firmware/ibft/target0/ip-addr: 192.168.79.116
/sys/firmware/ibft/target0/flags: 3
/sys/firmware/ibft/target0/index: 0
/sys/firmware/ibft/ethernet0/mac: 00:11:25:9d:8b:01
/sys/firmware/ibft/ethernet0/vlan: 0
/sys/firmware/ibft/ethernet0/gateway: 192.168.79.254
/sys/firmware/ibft/ethernet0/origin: 0
/sys/firmware/ibft/ethernet0/subnet-mask: 255.255.252.0
/sys/firmware/ibft/ethernet0/ip-addr: 192.168.77.41
/sys/firmware/ibft/ethernet0/flags: 7
/sys/firmware/ibft/ethernet0/index: 0
/sys/firmware/ibft/initiator/initiator-name: iqn.2007-07.com:konrad.initiator
/sys/firmware/ibft/initiator/flags: 3
/sys/firmware/ibft/initiator/index: 0

For full details of the IBFT structure please take a look at:
ftp://ftp.software.ibm.com/systems/support/system_x_pdf/ibm_iscsi_boot_firmware_table_v1.02.pdf

[akpm@linux-foundation.org: fix build]
Signed-off-by: Konrad Rzeszutek <konradr@linux.vnet.ibm.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Peter Jones <pjones@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

DMI-based module autoloading

The patch below adds DMI/SMBIOS based module autoloading to the Linux
kernel. The idea is to load laptop drivers automatically (and other
drivers which cannot be autoloaded otherwise), based on the DMI system
identification information of the BIOS.

Right now most distros manually try to load all available laptop
drivers on bootup in the hope that at least one of them loads
successfully. This patch does away with all that, and uses udev to
automatically load matching drivers on the right machines.

Basically the patch just exports the DMI information that has been
parsed by the kernel anyway to userspace via a sysfs device
/sys/class/dmi/id and makes sure that proper modalias attributes are
available. Besides adding the "modalias" attribute it also adds
attributes for a few other DMI fields which might be useful for
writing udev rules.

This patch is not an attempt to export the entire DMI/SMBIOS data to
userspace. We already have "dmidecode" which parses the complete DMI
info from userspace. The purpose of this patch is machine model
identification and good udev integration.

To take advantage of DMI based module autoloading, a driver should
export one or more MODULE_ALIAS fields similar to these:

MODULE_ALIAS("dmi:*:svnMICRO-STARINT'LCO.,LTD:pnMS-1013:pvr0131*:cvnMICRO-STARINT'LCO.,LTD:ct10:*");
MODULE_ALIAS("dmi:*:svnMicro-StarInternational:pnMS-1058:pvr0581:rvnMSI:rnMS-1058:*:ct10:*");
MODULE_ALIAS("dmi:*:svnMicro-StarInternational:pnMS-1412:*:rvnMSI:rnMS-1412:*:cvnMICRO-STARINT'LCO.,LTD:ct10:*");
MODULE_ALIAS("dmi:*:svnNOTEBOOK:pnSAM2000:pvr0131*:cvnMICRO-STARINT'LCO.,LTD:ct10:*");

These lines are specific to my msi-laptop.c driver. They are basically
just a concatenation of a few carefully selected DMI fields with all
potentially bad characters stripped.

Besides laptop drivers, modules like "hdaps", the i2c modules
and the hwmon modules are good candidates for "dmi:" MODULE_ALIAS
lines.

Besides merely exporting the DMI data via sysfs the patch adds
support for a few more DMI fields. Especially the CHASSIS fields are
very useful to identify different laptop modules. The patch also adds
working MODULE_ALIAS lines to my msi-laptop.c driver.

I'd like to thank Kay Sievers for helping me to clean up this patch
for posting it on lkml.

Patch is against Linus' current GIT HEAD. Should probably apply to
older kernels as well without modification.


Signed-off-by: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix several typos in drivers/

Signed-off-by: Adrian Bunk <bunk@stusta.de>

[PATCH] EDD isn't EXPERIMENTAL anymore

Lots of people use this. Apparently RH has for over 18 months so lets
drop EXPERIMENTAL.

Signed-off-by: Chris Wedgwood <cw@f00f.org>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] dell_rbu driver depends on x86[64]

This driver only appears on IA32 & EM64T boxes.

Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Don't set dcdbas driver to default m

It's nasty to set random drivers to default m because people who just press
enter on make oldconfig get these. Remove the default m

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] CONFIG_IA32

Add CONFIG_X86_32 for i386. This allows selecting options that only apply
to 32-bit systems.

(X86 && !X86_64) becomes X86_32
(X86 || X86_64) becomes X86

Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] dcdbas: add Dell Systems Management Base Driver with sysfs support

This patch adds the Dell Systems Management Base Driver with sysfs support.

This driver has been tested with Dell OpenManage.

Signed-off-by: Doug Warzecha <Douglas_Warzecha@dell.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] dell_rbu: new Dell BIOS update driver

Remote BIOS Update driver for updating BIOS images on Dell servers and
desktops. See dell_rbu.txt for details.

Signed-off-by: Abhay Salunke <Abhay_Salunke@dell.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!