crypto: qat - re-enable sriov after pf reset

When a Physical Function (PF) is reset, SR-IOV gets disabled, making the
associated Virtual Functions (VFs) unavailable. Even after reset and
using pci_restore_state, VFs remain uncreated because the numvfs still
at 0. Therefore, it's necessary to reconfigure SR-IOV to re-enable VFs.

This commit introduces the ADF_SRIOV_ENABLED configuration flag to cache
the SR-IOV enablement state. SR-IOV is only re-enabled if it was
previously configured.

This commit also introduces a dedicated workqueue without
`WQ_MEM_RECLAIM` flag for enabling SR-IOV during Heartbeat and CPM error
resets, preventing workqueue flushing warning.

This patch is based on earlier work done by Shashank Gupta.

Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: qat - enable dc chaining service

QAT GEN4 devices support chained compression operations. These
allow, with a single request to firmware, to hash then compress
data.

Extend the configuration to enable such mode. The cfg_services
operations in sysfs are extended to allow the string "dcc". When
selected, the driver downloads to the device both the symmetric
crypto and the compression firmware images and sends an admin message
to firmware which enables `chained` operations.
In addition, it sets the device's capabilities as the combination
of compression and symmetric crypto capabilities, while excluding
the ICP_ACCEL_CAPABILITIES_CRYPTO_SYMMETRIC bit to indicate
that in this mode, symmetric crypto instances are not supported.

When "dcc" is enabled, the device will handle compression requests
as if the "dc" configuration is loaded ("dcc" is a variation of "dc")
and the driver will register the acomp algorithms.

As for the other extended configurations, "dcc" is only available for
qat_4xxx devices and the chaining service will be only accessible from
user space.

Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: qat - add heartbeat feature

Under some circumstances, firmware in the QAT devices could become
unresponsive. The Heartbeat feature provides a mechanism to detect
unresponsive devices.

The QAT FW periodically writes to memory a set of counters that allow
to detect the liveness of a device. This patch adds logic to enable
the reporting of those counters, analyze them and report if a device
is alive or not.

In particular this adds
(1) heartbeat enabling, reading and detection logic
(2) reporting of heartbeat status and configuration via debugfs
(3) documentation for the newly created sysfs entries
(4) configuration of FW settings related to heartbeat, e.g. tick period
(5) logic to convert time in ms (provided by the user) to clock ticks

This patch introduces a new folder in debugfs called heartbeat with the
following attributes:
- status
- queries_sent
- queries_failed
- config

All attributes except config are reading only. In particular:
- `status` file returns 0 when device is operational and -1 otherwise.
- `queries_sent` returns the total number of heartbeat queries sent.
- `queries_failed` returns the total number of heartbeat queries failed.
- `config` allows to adjust the frequency at which the firmware writes
counters to memory. This period is given in milliseconds and it is
fixed for GEN4 devices.

Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: qat - expose pm_idle_enabled through sysfs

Expose 'pm_idle_enabled' sysfs attribute. This attribute controls how
idle conditions are handled. If it is set to 1 (idle support enabled)
when the device detects an idle condition, the driver will transition
the device to the 'MIN' power configuration.

In order to set the value of this attribute for a device, the device
must be in the 'down' state.

This only applies to qat_4xxx generation.

Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: qat - extend configuration for 4xxx

A QAT GEN4 device can be currently configured for crypto (sym;asym) or
compression (dc).

This patch extends the configuration to support more variations of these
services, download the correct FW images on the device and report the
correct capabilities on the device based on the configured service.

The device can now be configured with the following services:
"sym", "asym", "dc", "sym;asym", "asym;sym", "sym;dc", "dc;sym",
"asym;dc", "dc;asym".

With this change, the configuration "sym", "asym", "sym;dc", "dc;sym",
"asym;dc", "dc;asym" will be accessible only via userspace, i.e. the driver
for those configurations will not register into the crypto framework.
Support for such configurations in kernel will be enabled in a later
patch.

The pairs "sym;asym" and "asym;sym" result in identical device config.
As do "sym;dc", "dc;sym", and "asym;dc", "dc;asym".

Signed-off-by: Adam Guerin <adam.guerin@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

crypto: qat - Move driver to drivers/crypto/intel/qat

With the growing number of Intel crypto drivers, it makes sense to
group them all into a single drivers/crypto/intel/ directory.

Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>