clk: qcom: clk-krait: switch to .determine_rate

.determine_rate is meant to replace .round_rate. The former comes with a
benefit which is especially relevant on 32-bit systems: since
.determine_rate uses an "unsigned long" (compared to a "signed long"
which is used by .round_rate) the maximum value on 32-bit systems
increases from 2^31 (or approx. 2.14GHz) to 2^32 (or approx. 4.29GHz).

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Tested-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230212-clk-qcom-determine_rate-v1-1-b4e447d4926e@z3ntu.xyz

clk: qcom: clk-krait: fix wrong div2 functions

Currently div2 value is applied to the wrong bits. This is caused by a
bug in the code where the shift is done only for lpl, for anything
else the mask is not shifted to the correct bits.

Fix this by correctly shift if lpl is not supported.

Fixes: 4d7dc77babfe ("clk: qcom: Add support for Krait clocks")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221108215625.30186-1-ansuelsmth@gmail.com

clk: qcom: clk-krait: add apq/ipq8064 errata workaround

Add apq/ipq8064 errata workaround where the sec_src clock gating needs to
be disabled during switching. krait-cc compatible is not enough to
handle this and limit this workaround to apq/ipq8064. We check machine
compatible to handle this.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430054458.31321-4-ansuelsmth@gmail.com

clk: qcom: clk-krait: unlock spin after mux completion

Unlock spinlock after the mux switch is completed to prevent any corner
case of mux request while the switch still needs to be done.

Fixes: 4d7dc77babfe ("clk: qcom: Add support for Krait clocks")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430054458.31321-3-ansuelsmth@gmail.com

clk: qcom: Add safe switch hook for krait mux clocks

When the Hfplls are reprogrammed during the rate change,
the primary muxes which are sourced from the same hfpll
for higher frequencies, needs to be switched to the 'safe
secondary mux' as the parent for that small window. This
is done by registering a clk notifier for the muxes and
switching to the safe parent in the PRE_RATE_CHANGE notifier
and back to the original parent in the POST_RATE_CHANGE notifier.

Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: qcom: Add Krait clock controller driver

The Krait CPU clocks are made up of a primary mux and secondary
mux for each CPU and the L2, controlled via cp15 accessors. For
Kraits within KPSSv1 each secondary mux accepts a different aux
source, but on KPSSv2 each secondary mux accepts the same aux
source.

Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: qcom: Add support for Krait clocks

The Krait clocks are made up of a series of muxes and a divider
that choose between a fixed rate clock and dedicated HFPLLs for
each CPU. Instead of using mmio accesses to remux parents, the
Krait implementation exposes the remux control via cp15
registers. Support these clocks.

Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
[sboyd@kernel.org: Move hidden config to top outside of the visible qcom
config zone so that menuconfig looks nice]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>