clk: imx: remove clk_count of imx_register_uart_clocks

The clk count has been get with of_clk_get_parent_count, there is
no need to pass clk_count from users.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230104110032.1220721-4-peng.fan@oss.nxp.com

clk: imx: rename imx_obtain_fixed_clk_hw() to imx_get_clk_hw_by_name()

The imx_obtain_fixed_clk_hw name was wrong and misleading. Renaming it
to imx_get_clk_hw_by_name clarifies the purpose of the function, and
will allow it to be used not only for fixed rate clocks but also in
wider contexts.

No functional changes intended.

The replacements were made with the following command:

grep -rl 'imx_obtain_fixed_clk_hw' ./ | \
xargs sed -i 's/imx_obtain_fixed_clk_hw/imx_get_clk_hw_by_name/g'

Tested on a BSH SystemMaster (SMM) S2 board.

Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20221113180839.1625832-1-dario.binacchi@amarulasolutions.com

clk: imx: Update the pfdv2 for 8ulp specific support

On i.MX8ULP, the 'CLK_SET_RATE_PARENT' flag should NOT be
set and according to the laest RM, the PFD divider value range
seems will be changed in the future, so update the pfdv2 to
include the specific support for i.MX8ULP.

Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210914065208.3582128-8-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>

clk: imx: Update the pllv4 to support imx8ulp

The PLLs used on i.MX8ULP is mostly the same as on i.MX7ULP,
except the PLL register offset is changed. Change the PLLv4
driver for code reuse on i.MX7ULP and i.MX8ULP.

Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210914065208.3582128-3-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>

clk: imx: Fix reparenting of UARTs not associated with stdout

Most if not all i.MX SoC's call a function which enables all UARTS.
This is a problem for users who need to re-parent the clock source,
because any attempt to change the parent results in an busy error
due to the fact that the clocks have been enabled already.

clk: failed to reparent uart1 to sys_pll1_80m: -16

Instead of pre-initializing all UARTS, scan the device tree to see
which UART clocks are associated to stdout, and only enable those
UART clocks if it's needed early. This will move initialization of
the remaining clocks until after the parenting of the clocks.

When the clocks are shutdown, this mechanism will also disable any
clocks that were pre-initialized.

Fixes: 9461f7b33d11c ("clk: fix CLK_SET_RATE_GATE with clock rate protection")
Suggested-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>

clk: imx7ulp: make it easy to change ARM core clk

ARM clk could only source from divcore or hsrun_divcore.

Follow what we already used on i.MX7D and i.MX8M SoCs, use
imx_clk_hw_cpu API. When ARM core is running normaly,
whether divcore or hwrun_divcore will finally source
from SPLL_PFD0. However SPLL_PFD0 is marked with CLK_SET_GATE,
so we need to disable SPLL_PFD0, when configure the rate.
So add CORE and HSRUN_CORE virtual clk to make it easy to
configure the clk using imx_clk_hw_cpu API.

Since CORE and HSRUN_CORE already marked with CLK_IS_CRITICAL, no
need to set ARM as CLK_IS_CRITICAL. And when set the rate of ARM clk,
prograting it the parent with CLK_SET_RATE_PARENT will finally set
the SPLL_PFD0 clk.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx7ulp: Include clk-provider.h instead of clk.h

The i.MX7ULP clock driver is provider, NOT consumer, so clk-provider.h
should be used instead of clk.h.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx7up: Rename the clks to hws

This is just to keep in line with the other i.MX clock drivers that are
clk_hw based. Plus, it makes more sense to be called hws since its type is
clk_hw not clk.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx: Rename the imx_clk_divider_gate to imply it's clk_hw based

Renaming the imx_clk_divider_gate register function to imx_clk_hw_divider_gate
to be more obvious it is clk_hw based.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx: Rename the imx_clk_pfdv2 to imply it's clk_hw based

Renaming the imx_clk_pfdv2 register function to imx_clk_hw_pfdv2 to be
more obvious it is clk_hw based.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx: Rename the imx_clk_pllv4 to imply it's clk_hw based

Renaming the imx_clk_pllv4 register function to imx_clk_hw_pllv4 to be
more obvious it is clk_hw based.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx: imx7ulp composite: Rename to show is clk_hw based

Renaming the imx7ulp_clk_composite register function to
imx7ulp_clk_hw_composite to show it is clk_hw based.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx: clk-imx7ulp: Add missing sentinel of ulp_div_table

There should be a sentinel of ulp_div_table, otherwise _get_table_div
may access data out of the array.

Fixes: b1260067ac3d ("clk: imx: add imx7ulp clk driver")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx7ulp: Fix watchdog2 clock name typo

There is a typo in the watchdog2 clock name.

Fix it by changing it to "wdg2".

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx7ulp: do not export out IMX7ULP_CLK_MIPI_PLL clock

The mipi pll clock comes from the MIPI PHY PLL output, so
it should not be a fixed clock.

MIPI PHY PLL is in the MIPI DSI space, and it is used as
the bit clock for transferring the pixel data out and its
output clock is configured according to the display mode.

So it should be used only for MIPI DSI and not be exported
out for other usages.

Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx7ulp: Correct DDR clock mux options

In the latest reference manual Rev.0,06/2019, the DDR clock mux
is extended to 2 bits, and the clock options are also changed,
correct them accordingly.

Fixes: b1260067ac3d ("clk: imx: add imx7ulp clk driver")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx7ulp: Correct system clock source option #7

In the latest reference manual Rev.0,06/2019, the SCS's option #7
is no longer from upll, it is reserved, update clock driver accordingly.

Fixes: b1260067ac3d ("clk: imx: add imx7ulp clk driver")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx7ulp: Make sure earlycon's clock is enabled

Earlycon's clock could be disabled during kernel boot up,
if earlycon is enabled and its clock is gated, then kernel
boot up will fail. Make sure earlycon's clock is enabled
during kernel boot up.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx7ulp: update nic1_bus_clk parent info

Since i.MX7ULP B0 chip, nic1_bus_clk's parent is changed to
from nic0_clk directly, update it accordingly.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx7ulp: remove snvs clock

Since i.MX7ULP B0 chip, the SNVS module is moved into M4
domain and its clock is also moved into PCC0 which is
contorlled by M4, Linux kernel should NOT add it into
clock tree.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

clk: imx: imx7ulp: use struct_size() in kzalloc()

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
int stuff;
void *entry[];
};

instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

This issue was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: imx: imx7ulp: add arm hsrun mode clocks support

i.MX7ULP has a Cortex-A7 CPU which can run in RUN mode
or HSRUN mode, it is controlled in SMC1 module. The RUN
mode and HSRUN mode will use different clock source for
ARM, "divcore" for RUN mode and "hsrun_divcore" for HSRUN
mode, so the control bits in SMC1 module can be abstracted
as a HW clock mux, this patch adds HSRUN mode related
clocks in SCG1 module and adds "arm" clock in SMC1 module
to support RUN mode and HSRUN mode switch.

Latest clock tree in RUN mode as below:

firc 0 0 0 48000000 0 0 50000
firc_bus_clk 0 0 0 48000000 0 0 50000
hsrun_scs_sel 0 0 0 48000000 0 0 50000
hsrun_divcore 0 0 0 48000000 0 0 50000

sosc 3 3 3 24000000 0 0 50000
spll_pre_sel 1 1 1 24000000 0 0 50000
spll_pre_div 1 1 2 24000000 0 0 50000
spll 1 1 2 528000000 0 0 50000
spll_pfd0 1 1 1 500210526 0 0 50000
spll_pfd_sel 1 1 0 500210526 0 0 50000
spll_sel 1 1 0 500210526 0 0 50000
scs_sel 1 1 0 500210526 0 0 50000
divcore 1 1 0 500210526 0 0 50000
arm 1 1 0 500210526 0 0 50000

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

clk: imx: add imx7ulp clk driver

i.MX7ULP Clock functions are under joint control of the System
Clock Generation (SCG) modules, Peripheral Clock Control (PCC)
modules, and Core Mode Controller (CMC)1 blocks

The clocking scheme provides clear separation between M4 domain
and A7 domain. Except for a few clock sources shared between two
domains, such as the System Oscillator clock, the Slow IRC (SIRC),
and and the Fast IRC clock (FIRCLK), clock sources and clock
management are separated and contained within each domain.

M4 clock management consists of SCG0, PCC0, PCC1, and CMC0 modules.
A7 clock management consists of SCG1, PCC2, PCC3, and CMC1 modules.

This driver only adds clock support in A7 domain.

Note that most clocks required to be operated when gated, e.g. pll,
pfd, pcc. And more special cases that scs/ddr/nic mux selecting
different clock source requires that clock to be enabled first,
then we need set CLK_OPS_PARENT_ENABLE flag for them properly.

Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>