tpm: ibmvtpm: Correct the return value in tpm_ibmvtpm_probe()

Currently it returns zero when CRQ response timed out, it should return
an error code instead.

Fixes: d8d74ea3c002 ("tpm: ibmvtpm: Wait for buffer to be set before proceeding")
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>

tpm: ibmvtpm: Avoid error message when process gets signal while waiting

When rngd is run as root then lots of these types of message will appear
in the kernel log if the TPM has been configured to provide random bytes:

[ 7406.275163] tpm tpm0: tpm_transmit: tpm_recv: error -4

The issue is caused by the following call that is interrupted while
waiting for the TPM's response.

sig = wait_event_interruptible(ibmvtpm->wq, !ibmvtpm->tpm_processing_cmd);

Rather than waiting for the response in the low level driver, have it use
the polling loop in tpm_try_transmit() that uses a command's duration to
poll until a result has been returned by the TPM, thus ending when the
timeout has occurred but not responding to signals and ctrl-c anymore. To
stay in this polling loop extend tpm_ibmvtpm_status() to return
'true' for as long as the vTPM is indicated as being busy in
tpm_processing_cmd. Since the loop requires the TPM's timeouts, get them
now using tpm_get_timeouts() after setting the TPM2 version flag on the
chip.

To recreat the resolved issue start rngd like this:

sudo rngd -r /dev/hwrng -t
sudo rngd -r /dev/tpm0 -t

Link: https://bugzilla.redhat.com/show_bug.cgi?id=1981473
Fixes: 6674ff145eef ("tpm_ibmvtpm: properly handle interrupted packet receptions")
Cc: Nayna Jain <nayna@linux.ibm.com>
Cc: George Wilson <gcwilson@linux.ibm.com>
Reported-by: Nageswara R Sastry <rnsastry@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Nageswara R Sastry <rnsastry@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>

vio: make remove callback return void

The driver core ignores the return value of struct bus_type::remove()
because there is only little that can be done. To simplify the quest to
make this function return void, let struct vio_driver::remove() return
void, too. All users already unconditionally return 0, this commit makes
it obvious that returning an error code is a bad idea.

Note there are two nominally different implementations for a vio bus:
one in arch/sparc/kernel/vio.c and the other in
arch/powerpc/platforms/pseries/vio.c. This patch only adapts the powerpc
one.

Before this patch for a device that was bound to a driver without a
remove callback vio_cmo_bus_remove(viodev) wasn't called. As the device
core still considers the device unbound after vio_bus_remove() returns
calling this unconditionally is the consistent behaviour which is
implemented here.

Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Lijun Pan <ljp@linux.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[mpe: Drop unneeded hvcs_remove() forward declaration, squash in
change from sfr to drop ibmvnic_remove() forward declaration]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210225221834.160083-1-uwe@kleine-koenig.org

tpm: ibmvtpm: Wait for ready buffer before probing for TPM2 attributes

The tpm2_get_cc_attrs_tbl() call will result in TPM commands being issued,
which will need the use of the internal command/response buffer. But,
we're issuing this *before* we've waited to make sure that buffer is
allocated.

This can result in intermittent failures to probe if the hypervisor / TPM
implementation doesn't respond quickly enough. I find it fails almost
every time with an 8 vcpu guest under KVM with software emulated TPM.

To fix it, just move the tpm2_get_cc_attrs_tlb() call after the
existing code to wait for initialization, which will ensure the buffer
is allocated.

Fixes: 18b3670d79ae9 ("tpm: ibmvtpm: Add support for TPM2")
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

tpm: ibmvtpm: retry on H_CLOSED in tpm_ibmvtpm_send()

tpm_ibmvtpm_send() can fail during PowerVM Live Partition Mobility resume
with an H_CLOSED return from ibmvtpm_send_crq(). The PAPR says, 'The
"partner partition suspended" transport event disables the associated CRQ
such that any H_SEND_CRQ hcall() to the associated CRQ returns H_Closed
until the CRQ has been explicitly enabled using the H_ENABLE_CRQ hcall.'
This patch adds a check in tpm_ibmvtpm_send() for an H_CLOSED return from
ibmvtpm_send_crq() and in that case calls tpm_ibmvtpm_resume() and
retries the ibmvtpm_send_crq() once.

Cc: stable@vger.kernel.org # 3.7.x
Fixes: 132f76294744 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Reported-by: Linh Pham <phaml@us.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: George Wilson <gcwilson@linux.ibm.com>
Tested-by: Linh Pham <phaml@us.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

tpm: ibmvtpm: Add support for TPM2

Support TPM2 in the IBM vTPM driver. The hypervisor tells us what
version of TPM is connected through the vio_device_id.

In case a TPM2 device is found, we set the TPM_CHIP_FLAG_TPM2 flag
and get the command codes attributes table. The driver does
not need the timeouts and durations, though.

Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Acked-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: Nayna Jain <nayna@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

tpm: ibmvtpm: Wait for buffer to be set before proceeding

Synchronize with the results from the CRQs before continuing with
the initialization. This avoids trying to send TPM commands while
the rtce buffer has not been allocated, yet.

This patch fixes an existing race condition that may occurr if the
hypervisor does not quickly respond to the VTPM_GET_RTCE_BUFFER_SIZE
request sent during initialization and therefore the ibmvtpm->rtce_buf
has not been allocated at the time the first TPM command is sent.

Fixes: 132f76294744 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Acked-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: Nayna Jain <nayna@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 315 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm: Unify the send callback behaviour

The send() callback should never return length as it does not in every
driver except tpm_crb in the success case. The reason is that the main
transmit functionality only cares about whether the transmit was
successful or not and ignores the count completely.

Suggested-by: Stefan Berger <stefanb@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>

tpm: tpm_ibmvtpm: fix kdoc warnings

Remove redundant lines in the kdoc:

Fixes kdoc warnings:

drivers/char/tpm/tpm_ibmvtpm.c:42: warning: Cannot understand *
on line 42 - I thought it was a doc line
drivers/char/tpm/tpm_ibmvtpm.c:57: warning: Cannot understand *
on line 57 - I thought it was a doc line

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

tpm: ibmvtpm: simplify crq initialization and document crq format

The crq is passed in registers and is the same on BE and LE hosts.
However, current implementation allocates a structure on-stack to
represent the crq, initializes the members swapping them to BE, and
loads the structure swapping it from BE. This is pointless and causes
GCC warnings about ununitialized members. Get rid of the structure and
the warnings.

Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

tpm: vtpm: constify vio_device_id

vio_device_id are not supposed to change at runtime. All functions
working with vio_device_id provided by <asm/vio.h> work with
const vio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

vTPM: Fix missing NULL check

The current code passes the address of tpm_chip as the argument to
dev_get_drvdata() without prior NULL check in
tpm_ibmvtpm_get_desired_dma. This resulted an oops during kernel
boot when vTPM is enabled in Power partition configured in active
memory sharing mode.

The vio_driver's get_desired_dma() is called before the probe(), which
for vtpm is tpm_ibmvtpm_probe, and it's this latter function that
initializes the driver and set data. Attempting to get data before
the probe() caused the problem.

This patch adds a NULL check to the tpm_ibmvtpm_get_desired_dma.

fixes: 9e0d39d8a6a0 ("tpm: Remove useless priv field in struct tpm_vendor_specific")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkine <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

tpm/vtpm: fix kdoc warnings

Use corret kdoc format for function description and eliminate warning
of type:

tpm_ibmvtpm.c:66: warning: No description found for parameter 'count'

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

tpm: fix for typo in tpm/tpm_ibmvtpm.c

Fixes: 28157164b056 ("tpm: Remove useless priv field in struct tpm_vendor_specific")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

tpm: Remove useless priv field in struct tpm_vendor_specific

Remove useless priv field in struct tpm_vendor_specific and take benefit
of chip->dev.driver_data. As priv is the latest field available in
struct tpm_vendor_specific, remove any reference to that structure.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

tpm_ibmvtpm: properly handle interrupted packet receptions

When the TPM response reception is interrupted in the wait_event_interruptable
call, the TPM is still busy processing the command and will only deliver the
response later. So we have to wait for an outstanding response before sending
a new request to avoid trying to put a 2nd request into the CRQ. Also reset
the res_len before sending a command so we will end up in that
wait_event_interruptable() waiting for the response rather than reading the
command packet as a response.

The easiest way to trigger the problem is to run the following

cd /sys/device/vio/71000004

while :; cat pcrs >/dev/null; done

And press Ctrl-C. This will then display an error

tpm_ibmvtpm 71000004: tpm_transmit: tpm_recv: error -4

followed by several other errors once interaction with the TPM resumes.

tpm_ibmvtpm 71000004: A TPM error (101) occurred attempting to determine the number of PCRS.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Ashley Lai <ashley@ashleylai.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>

vTPM: fix memory allocation flag for rtce buffer at kernel boot

At ibm vtpm initialzation, tpm_ibmvtpm_probe() registers its interrupt
handler, ibmvtpm_interrupt, which calls ibmvtpm_crq_process to allocate
memory for rtce buffer. The current code uses 'GFP_KERNEL' as the
type of kernel memory allocation, which resulted a warning at
kernel/lockdep.c. This patch uses 'GFP_ATOMIC' instead so that the
allocation is high-priority and does not sleep.

Cc: stable@kernel.org
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>

vTPM: set virtual device before passing to ibmvtpm_reset_crq

tpm_ibmvtpm_probe() calls ibmvtpm_reset_crq(ibmvtpm) without having yet
set the virtual device in the ibmvtpm structure. So in ibmvtpm_reset_crq,
the phype call contains empty unit addresses, ibmvtpm->vdev->unit_address.

Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Cc: <stable@vger.kernel.org>
Fixes: 132f76294744 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>

tpm/ibmvtpm: Additional LE support for tpm_ibmvtpm_send

Problem: When IMA and VTPM are both enabled in kernel config,
kernel hangs during bootup on LE OS.

Why?: IMA calls tpm_pcr_read() which results in tpm_ibmvtpm_send
and tpm_ibmtpm_recv getting called. A trace showed that
tpm_ibmtpm_recv was hanging.

Resolution: tpm_ibmtpm_recv was hanging because tpm_ibmvtpm_send
was sending CRQ message that probably did not make much sense
to phype because of Endianness. The fix below sends correctly
converted CRQ for LE. This was not caught before because it
seems IMA is not enabled by default in kernel config and
IMA exercises this particular code path in vtpm.

Tested with IMA and VTPM enabled in kernel config and VTPM
enabled on both a BE OS and a LE OS ppc64 lpar. This exercised
CRQ and TPM command code paths in vtpm.
Patch is against Peter's tpmdd tree on github which included
Vicky's previous vtpm le patches.

Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # eb71f8a5e33f: "Added Little Endian support to vtpm module"
Cc: <stable@vger.kernel.org>
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>

tpm/ibmvtpm: Additional LE support for tpm_ibmvtpm_send

Problem: When IMA and VTPM are both enabled in kernel config,
kernel hangs during bootup on LE OS.

Why?: IMA calls tpm_pcr_read() which results in tpm_ibmvtpm_send
and tpm_ibmtpm_recv getting called. A trace showed that
tpm_ibmtpm_recv was hanging.

Resolution: tpm_ibmtpm_recv was hanging because tpm_ibmvtpm_send
was sending CRQ message that probably did not make much sense
to phype because of Endianness. The fix below sends correctly
converted CRQ for LE. This was not caught before because it
seems IMA is not enabled by default in kernel config and
IMA exercises this particular code path in vtpm.

Tested with IMA and VTPM enabled in kernel config and VTPM
enabled on both a BE OS and a LE OS ppc64 lpar. This exercised
CRQ and TPM command code paths in vtpm.
Patch is against Peter's tpmdd tree on github which included
Vicky's previous vtpm le patches.

Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # eb71f8a5e33f: "Added Little Endian support to vtpm module"
Cc: <stable@vger.kernel.org>
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>

Added Little Endian support to vtpm module

The tpm_ibmvtpm module is affected by an unaligned access problem.
ibmvtpm_crq_get_version failed with rc=-4 during boot when vTPM is
enabled in Power partition, which supports both little endian and
big endian modes.

We added little endian support to fix this problem:
1) added cpu_to_be64 calls to ensure BE data is sent from an LE OS.
2) added be16_to_cpu and be32_to_cpu calls to make sure data received
is in LE format on a LE OS.

Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>
[phuewe: manually applied the patch :( ]
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>

tpm: two-phase chip management functions

tpm_register_hardware() and tpm_remove_hardware() are called often
before initializing the device. The problem is that the device might
not be fully initialized when it comes visible to the user space.

This patch resolves the issue by diving initialization into two
parts:

- tpmm_chip_alloc() creates struct tpm_chip.

- tpm_chip_register() sets up the character device and sysfs
attributes.

The framework takes care of freeing struct tpm_chip by using the devres
API. The broken release callback has been wiped. ACPI drivers do not
ever get this callback.

Regards to Jason Gunthorpe for carefully reviewing this part of the
code.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Peter Huewe <peterhuewe@gmx.de>
[phuewe: update to upstream changes]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>

tpm_ibmvtpm: Update email address in maintainers list and ibmvtpm driver

Added myself as a maintainer for the IBM vtpm driver and removed myself
from the tpm maintainer list. Also, updated the tpm_ibmvtpm driver with
my current email address.

Signed-off-by: Ashley Lai <ashleydlai@gmail.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>

tpm: Fix NULL return in tpm_ibmvtpm_get_desired_dma

There was an oops in tpm_ibmvtpm_get_desired_dma, which caused
kernel panic during boot when vTPM is enabled in Power partition
configured in AMS mode.

vio_bus_probe calls vio_cmo_bus_probe which calls
tpm_ibmvtpm_get_desired_dma to get the size needed for DMA allocation.
The problem is, vio_cmo_bus_probe is called before calling probe, which
for vtpm is tpm_ibmvtpm_probe and it's this function that initializes
and sets up vtpm's CRQ and gets required data values. Therefore,
since this has not yet been done, NULL is returned in attempt to get
the size for DMA allocation.

We added a NULL check. In addition, a default buffer size will
be set when NULL is returned.

Cc: <stable@vger.kernel.org>
Signed-off-by: Hon Ching (Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>

tpm: Create a tpm_class_ops structure and use it in the drivers

This replaces the static initialization of a tpm_vendor_specific
structure in the drivers with the standard Linux idiom of providing
a const structure of function pointers.

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
[phuewe: did apply manually due to commit
191ffc6bde3 tpm/tpm_i2c_atmel: fix coccinelle warnings]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>

tpm: Pull all driver sysfs code into tpm-sysfs.c

The tpm core now sets up and controls all sysfs attributes, instead
of having each driver have a unique take on it.

All drivers now now have a uniform set of attributes, and no sysfs
related entry points are exported from the tpm core module.

This also uses the new method used to declare sysfs attributes
with DEVICE_ATTR_RO and 'struct attribute *'

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: had to apply the tpm_i2c_atmel part manually due to commit
191ffc6bde3fc tpm/tpm_i2c_atmel: fix coccinelle warnings]

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>

tpm: Pull everything related to /dev/tpmX into tpm-dev.c

CLASS-dev.c is a common idiom for Linux subsystems

This pulls all the code related to the miscdev into tpm-dev.c and makes it
static. The identical file_operation structs in the drivers are purged and the
tpm common code unconditionally creates the miscdev.

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
[phuewe:
tpm_dev_release is now used only in this file, thus the EXPORT_SYMBOL
can be dropped and the function be marked as static.
It has no other in-kernel users]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>

tpm/tpm_ibmvtpm: fix unreachable code warning (smatch warning)

smatch complains:
drivers/char/tpm/tpm_ibmvtpm.c:510
ibmvtpm_crq_process() info: ignoring unreachable code.

-> The return is not necessary here, remove it

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>

tpm: Remove tpm_show_caps_1_2

The version of the TPM should not depend on the bus it is connected
through. 1.1, 1.2 and soon 2.0 TPMS will be all be able to use the
same bus interfaces.

Make tpm_show_caps try the 1.2 capability first. If that fails then
fall back to the 1.1 capability. This effectively auto-detects what
interface the TPM supports at run-time.

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>

tpm: ibmvtpm: Use %zd formatting for size_t format arguments

This suppresses compile warnings on 32 bit builds.

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Ashley Lai <adlai@linux.vnet.ibm.com>

tpm: Fix cancellation of TPM commands (polling mode)

On one of my machines the cancellation of TPM commands does not work.
The reason is that by writing into sysfs 'cancel' the tpm_tis_ready
call causes the status flag TPM_STS_VALID to be set in the statusregister.
However, the TIS driver seems to wait for TPM_STS_COMMAND_READY.
Once a 2nd time sysfs 'cancel' is written to, the TPM_STS_COMMAND_READY flag
also gets set, resulting in TPM_STS_VALID|TPM_STS_COMMAND_READY to be
read from the status register.

This patch now converts req_canceled into a function to enable more complex
comparisons against possible cancellation status codes.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>

tpm: rename vendor data to priv and provide an accessor

"data" was too generic a name for what's being used as a generic
private pointer by vendor-specific code. Rename it to "priv" and provide
a #define for users.

Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>

tpm: remove use of __devinit

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Rajiv Andrade <mail@srajiv.net>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Cc: Sirrix AG <tpmdd@sirrix.com>
Acked-by: Kent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

char: remove use of __devexit

CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: David Airlie <airlied@linux.ie>
Cc: Olof Johansson <olof@lixom.net>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Rajiv Andrade <mail@srajiv.net>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Cc: Sirrix AG <tpmdd@sirrix.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: openipmi-developer@lists.sourceforge.net
Cc: platform-driver-x86@vger.kernel.org
Cc: tpmdd-devel@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

char: remove use of __devinitdata

CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: David Airlie <airlied@linux.ie>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Rajiv Andrade <mail@srajiv.net>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Cc: Sirrix AG <tpmdd@sirrix.com>
Cc: openipmi-developer@lists.sourceforge.net
Cc: tpmdd-devel@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/char/tpm: remove tasklet and cleanup

This patch removed the tasklet and moved the wait queue into the
private structure. It also cleaned up the response CRQ path.

Signed-off-by: Ashley Lai <adlai@us.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>

drivers/char/tpm: Add new device driver to support IBM vTPM

This patch adds a new device driver to support IBM virtual TPM
(vTPM) for PPC64. IBM vTPM is supported through the adjunct
partition with firmware release 740 or higher. With vTPM
support, each lpar is able to have its own vTPM without the
physical TPM hardware.

This driver provides TPM functionalities by communicating with
the vTPM adjunct partition through Hypervisor calls (Hcalls)
and Command/Response Queue (CRQ) commands.

Signed-off-by: Ashley Lai <adlai@us.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>