agp/amd64: Update to DEFINE_SIMPLE_DEV_PM_OPS()

As of 1a3c7bb08826 ("PM: core: Add new *_PM_OPS macros, deprecate old
ones"), SIMPLE_DEV_PM_OPS() is deprecated in favor of
DEFINE_SIMPLE_DEV_PM_OPS(), which has the advantage that the PM callbacks
don't need to be wrapped with #ifdef CONFIG_PM or tagged with
__maybe_unused.

Convert to DEFINE_SIMPLE_DEV_PM_OPS(). No functional change intended.

Link: https://lore.kernel.org/r/20221025203852.681822-7-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Dave Airlie <airlied@redhat.com>

x86/amd_nb: Unexport amd_cache_northbridges()

amd_cache_northbridges() is exported by amd_nb.c and is called by
amd64-agp.c and amd64_edac.c modules at module_init() time so that NB
descriptors are properly cached before those drivers can use them.

However, the init_amd_nbs() initcall already does call
amd_cache_northbridges() unconditionally and thus makes sure the NB
descriptors are enumerated.

That initcall is a fs_initcall type which is on the 5th group (starting
from 0) of initcalls that gets run in increasing numerical order by the
init code.

The module_init() call is turned into an __initcall() in the MODULE=n
case and those are device-level initcalls, i.e., group 6.

Therefore, the northbridges caching is already finished by the time
module initialization starts and thus the correct initialization order
is retained.

Unexport amd_cache_northbridges(), update dependent modules to
call amd_nb_num() instead. While at it, simplify the checks in
amd_cache_northbridges().

[ bp: Heavily massage and *actually* explain why the change is ok. ]

Signed-off-by: Muralidhara M K <muralimk@amd.com>
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220324122729.221765-1-nchatrad@amd.com

amd64-agp: convert to generic power management

Convert amd64-agp from legacy PCI power management to the generic power
management framework.

Previously, amd64-agp used legacy PCI power management, and
agp_amd64_suspend() and agp_amd64_resume() were responsible for both
device-specific things and generic PCI things:

agp_amd64_suspend
pci_save_state(pdev) <-- generic PCI
pci_set_power_state(pdev, pci_choose_state(pdev, state)) <-- generic PCI

agp_amd64_resume
pci_set_power_state(pdev, PCI_D0) <-- generic PCI
pci_restore_state(pdev) <-- generic PCI
nforce3_agp_init() <-- device-specific
amd_8151_configure() <-- device-specific

With generic power management, the PCI bus PM methods do the generic PCI
things, and the driver needs only the device-specific part, i.e.,

suspend_devices_and_enter
dpm_suspend_start(PMSG_SUSPEND)
pci_pm_suspend # PCI bus .suspend() method
agp_amd64_suspend <-- not needed at all; removed
suspend_enter
dpm_suspend_noirq(PMSG_SUSPEND)
pci_pm_suspend_noirq # PCI bus .suspend_noirq() method
pci_save_state <-- generic PCI
pci_prepare_to_sleep <-- generic PCI
pci_set_power_state
...
dpm_resume_end(PMSG_RESUME)
pci_pm_resume # PCI bus .resume() method
pci_restore_standard_config
pci_set_power_state(PCI_D0) <-- generic PCI
pci_restore_state <-- generic PCI
agp_amd64_resume # dev->driver->pm->resume
nforce3_agp_init() <-- device-specific
amd_8151_configure() <-- device-specific

[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211208193305.147072-2-helgaas@kernel.org
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Dave Airlie <airlied@redhat.com>

x86/amd_nb, char/amd64-agp: Use amd_nb_num() accessor

... to find whether there are northbridges present on the
system. Convert the last forgotten user and therefore, unexport
amd_nb_misc_ids[] too.

Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Michal Kubecek <mkubecek@suse.cz>
Cc: Yazen Ghannam <yazen.ghannam@amd.com>
Link: https://lkml.kernel.org/r/20200316150725.925-1-bp@alien8.de

treewide: Add SPDX license identifier for more missed files

Add SPDX license identifiers to all files which:

- Have no license information of any form

- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

char: amd64-agp: Use 64-bit arithmetic instead of 32-bit

Cast *tmp* and *nb_base* to u64 in order to give the compiler
complete information about the proper arithmetic to use.

Notice that such variables are used in contexts that expect
expressions of type u64 (64 bits, unsigned) and the following
expressions are currently being evaluated using 32-bit arithmetic:

tmp << 25
nb_base << 25

Addresses-Coverity-ID: 200586 ("Unintentional integer overflow")
Addresses-Coverity-ID: 200587 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

agp: amd64: constify pci_device_id.

pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

x86/boot/e820: Move asm/e820.h to asm/e820/api.h

In line with asm/e820/types.h, move the e820 API declarations to
asm/e820/api.h and update all usage sites.

This is just a mechanical, obviously correct move & replace patch,
there will be subsequent changes to clean up the code and to make
better use of the new header organization.

Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Jackson <pj@sgi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

agp: Fix up email address & attributions in AGP MODULE_AUTHOR tags

- Remove soon-to-be-dead @redhat address.
- Jeff Hartmann wrote the bulk of the original backend code, and should
at least get a mention in the MODULE_AUTHOR for backend.o
- Various people at Intel have done a lot more work than myself on the
intel-* drivers, so again, mention that.

Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

agp: Support 64-bit APBASE

Per the AGP 3.0 spec, APBASE is a standard PCI BAR and may be either 32
bits or 64 bits wide. Many drivers read APBASE directly, but they only
handled 32-bit BARs.

The PCI core reads APBASE at enumeration-time. Use pci_bus_address()
instead of reading it again in the driver. This works correctly for both
32-bit and 64-bit BARs.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

char: amd64-agp: remove DEFINE_PCI_DEVICE_TABLE macro

Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Drivers: char: remove __dev* attributes.

CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: David Airlie <airlied@linux.ie>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

char: remove use of __devexit

CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: David Airlie <airlied@linux.ie>
Cc: Olof Johansson <olof@lixom.net>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Rajiv Andrade <mail@srajiv.net>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Cc: Sirrix AG <tpmdd@sirrix.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: openipmi-developer@lists.sourceforge.net
Cc: platform-driver-x86@vger.kernel.org
Cc: tpmdd-devel@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

module_param: make bool parameters really bool (drivers & misc)

module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.

It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.

Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

amd64-agp: fix crash at second module load

The module forgot to sometimes unregister some resources.

This fixes Bug #22882.

[Patch updated to 2.6.38-rc3 by Randy Dunlap.]
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

x86, amd-nb: Cleanup AMD northbridge caching code

Support more than just the "Misc Control" part of the northbridges.
Support more flags by turning "gart_supported" into a single bit flag
that is stored in a flags member. Clean up related code by using a set
of functions (amd_nb_num(), amd_nb_has_feature() and node_to_amd_nb())
instead of accessing the NB data structures directly. Reorder the
initialization code and put the GART flush words caching in a separate
function.

Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

x86, amd-nb: Complete the rename of AMD NB and related code

Not only the naming of the files was confusing, it was even more so for
the function and variable names.

Renamed the K8 NB and NUMA stuff that is also used on other AMD
platforms. This also renames the CONFIG_K8_NUMA option to
CONFIG_AMD_NUMA and the related file k8topology_64.c to
amdtopology_64.c. No functional changes intended.

Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

x86, k8: Rename k8.[ch] to amd_nb.[ch] and CONFIG_K8_NB to CONFIG_AMD_NB

The file names are somehow misleading as the code is not specific to
AMD K8 CPUs anymore. The files accomodate code for other AMD CPU
northbridges as well.

Same is true for the config option which is valid for AMD CPU
northbridges in general and not specific to K8.

Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20100917160343.GD4958@loge.amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>

x86, k8-gart: Decouple handling of garts and northbridges

So far we only provide num_k8_northbridges. This is required in
different areas (e.g. L3 cache index disable, GART). But not all AMD
CPUs provide a GART. Thus it is useful to split off the GART handling
from the generic caching of AMD northbridge misc devices.

Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20100917160254.GC4958@loge.amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>

x86, GART: Disable GART table walk probes

Current code tramples over bit F3x90[6] which can be used to
disable GART table walk probes. However, this bit should be set
for performance reasons (speed up GART table walks). We are
allowed to do that since we put GART tables in UC memory later
anyway. Make it so.

Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
LKML-Reference: <1283531981-7495-3-git-send-email-bp@amd64.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86, GART: Remove superfluous AMD64_GARTEN

There is a GARTEN so use that and drop the duplicate.

Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
LKML-Reference: <1283531981-7495-2-git-send-email-bp@amd64.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

agp: amd64, fix pci reference leaks

Stanse found pci reference leaks in uli_agp_init and nforce3_agp_init
initialization functions.

The PCI devices are bridges, so it's not critical, but still worth fixing.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

amd64-agp: Probe unknown AGP devices the right way

The current initialisation code probes 'unsupported' AGP devices
simply by calling its own probe function. It does not lock these
devices or even check whether another driver is already bound to
them.

We must use the device core to manage this. So if the specific
device id table didn't match anything and agp_try_unsupported=1,
switch the device id table and call driver_attach() again.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>

agp: use scratch page on memory remove and at GATT creation V4

Convert most AGP chipset to use scratch page as default entries.
This help avoiding GPU querying 0 address and trigger computer
fault. With KMS and memory manager we bind/unbind AGP memory
constantly and it seems that some GPU are still doing AGP
traffic even after GPU report being idle with the memory segment.

Tested (radeon GPU KMS + Xorg + compiz + glxgears + quake3) on :
- SIS 1039:0001 & 1039:0003
- Intel 865 8086:2571

Compile tested for other bridges

V2 enable scratch page on uninorth
V3 fix unbound check in uninorth insert memory (Michel Dänzer)
V4 rebase on top of drm-next branch with the lastest intel AGP
changeset (stable should use version V3 of the patch)

Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

x86/agp: Fix amd64-agp module initialization regression

This fixes the regression introduced by commit
42590a75019a50012f25a962246498dead428433 ("x86/agp: Fix
agp_amd64_init and agp_amd64_cleanup").

The commit 61684ceaad4f65d1a9832c722f7bd5e7fc714de9 fixed the
above regression but it's not enough. When amd64-agp is built as
a module, AGP isn't initialized, iommu is initialized, all the
aperture is owned by the iommu.

Reported-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Marin Mitov <mitov@issp.bas.bg>
LKML-Reference: <20100204090802S.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86/agp: Fix agp_amd64_init regression

This fixes the regression introduced by commit
42590a75019a50012f25a962246498dead428433 ("x86/agp: Fix
agp_amd64_init and agp_amd64_cleanup").

The above commit changes agp_amd64_init() not to do anything if
gart_iommu_aperture is not zero.

If GART iommu calls agp_amd64_init(), we need to skip
agp_amd64_init() when it's called later via module_init.

The problem is that gart_iommu_init() calls agp_amd64_init()
with not zero gart_iommu_aperture so agp_amd64_init() is never
initialized.

When gart_iommu_init() calls agp_amd64_init(), agp should be
always initialized.

Reported-by: Marin Mitov <mitov@issp.bas.bg>
Reported-by: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Marin Mitov <mitov@issp.bas.bg>
Tested-by: Kevin Winchester <kjwinchester@gmail.com>
Cc: davej@redhat.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20100125141006O.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86/agp: Fix agp_amd64_init and agp_amd64_cleanup

This fixes the regression introduced by the commit
f405d2c02395a74d3883bd03ded36457aa3697ad.

The above commit fixes the following issue:

http://marc.info/?l=linux-kernel&m=126192729110083&w=2

However, it doesn't work properly when you remove and insert the
agp_amd64 module again.

agp_amd64_init() and agp_amd64_cleanup should be called only
when gart_iommu is not called earlier (that is, the GART IOMMU
is not enabled). We need to use 'gart_iommu_aperture' to see if
GART IOMMU is enabled or not.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: mitov@issp.bas.bg
Cc: davej@redhat.com
LKML-Reference: <20100104161603L.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86/agp: Fix agp_amd64_init() initialization with CONFIG_GART_IOMMU enabled

with CONFIG_GART_IOMMU enabled drivers/char/agp/amd64-agp.c has:

#ifndef CONFIG_GART_IOMMU
module_init(agp_amd64_init);
module_exit(agp_amd64_cleanup);
#endif

agp_amd64_init() was called via gart_iommu_init with
CONFIG_GART_IOMMU=y agp_amd64_init() was called via module_init
with CONFIG_GART_IOMMU=n

The commit 75f1cdf1dda92cae037ec848ae63690d91913eac changes the
x86 dma initialization routine: gart_iommu_init() is called only
when GART IOMMU is detected. So when GART IOMMU isn't detected,
agp_amd64_init isn't called.

Marin Mitov reported this issue:

http://marc.info/?l=linux-kernel&m=126192729110083&w=2

With this patch, agp_amd64_init() is always called via
module_init (the above ifndef is removed). If agp_amd64_init()
is called via gart_iommu_init() earlier, agp_amd64_init()
finishes without doing anything (when it is called via
module_init).

Reported-by: Marin Mitov <mitov@issp.bas.bg>
Tested-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: davej@redhat.com
LKML-Reference: <20091228181118C.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

agp: kill phys_to_gart() and gart_to_phys()

There seems to be no reason for these -- they're a 1:1 mapping on all
platforms.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

agp: Switch mask_memory() method to take address argument again, not page

In commit 07613ba2 ("agp: switch AGP to use page array instead of
unsigned long array") we switched the mask_memory() method to take a
'struct page *' instead of an address. This is painful, because in some
cases it has to be an IOMMU-mapped virtual bus address (in fact,
shouldn't it _always_ be a dma_addr_t returned from pci_map_xxx(), and
we just happen to get lucky most of the time?)

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

agp: switch AGP to use page array instead of unsigned long array

This switches AGP to use an array of pages for tracking the
pages allocated to the GART. This should enable GEM on PAE to work
a lot better as we can pass highmem pages to the PAT code and it will
do the right thing with them.

Signed-off-by: Dave Airlie <airlied@redhat.com>

x86/agp: tighten check to update amd nb aperture

Impact: fix bug to make agp work with dri

Jeffrey reported that dri does work with 64bit, but doesn't work with
32bit it turns out NB aperture is 32M, aperture on agp is 128M

64bit is using 64M for vaidation for 64 iommu/gart 32bit is only using
32M..., and will not update the nb aperture.

So try to compare nb apterture and agp apterture before leaving not
touch nb aperture.

Reported-by: Jeffrey Trull <jetrull@sbcglobal.net>
Tested-by: Jeffrey Trull <jetrull@sbcglobal.net>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Update email addresses.

Update assorted email addresses and related info to point
to a single current, valid address.

additionally
- trivial CREDITS entry updates. (Not that this file means much any more)
- remove arjans dead redhat.com address from powernow driver

Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

agp: enable optimized agp_alloc_pages methods

The pageattr-array patch that you currently have in tip/master only
enables it for intel-agp, not the others. The attached enables it for
all drivers currently directly using agp_generic_alloc_page() and
agp_generic_destroy_page() (ocal driver is amd-k7-agp).

The new agp_generic_alloc_pages() interface uses the also new
pageattr array interface API. This makes all AGP drivers that
up to now used generic_{alloc,destroy}_page() use it.

Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

agp: use dev_printk when possible

Convert printks to use dev_printk().

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

amd64-agp: run fallback when no bridges found, not when driver registration fails

I think the intent was that if no bridges matched agp_amd64_pci_table[],
we would fall back to checking for any bridge with the AGP capability.
But in the current code, we execute the fallback path only when
pci_register_driver() itself fails, which is unrelated to whether any
matching devices were found.

This patch counts the AGP bridges found in the probe() method and executes
the fallback path when none is found.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drivers/char/agp - use bool

Use boolean in AGP instead of having own TRUE/FALSE

--
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

x86, aperture_64: use symbolic constants

Factor-out common aperture_valid code.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

x86 gart: factor out common code

Cleanup gart handling on amd64 a bit: move common code into
enable_gart_translation , and use symbolic register names where
appropriate.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

x86: checking aperture size order

some systems are using 32M for gart and agp when memory is less than 4G.
Kernel will reject and try to allcate another 64M that is not needed,
and we will waste 64M of perfectly good RAM.

this patch adds a workaround by checking aper_base/order between NB and
agp bridge. If they are the same, and memory size is less than 4G, it
will allow it.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

x86: agp_gart size checking for buggy device

while looking at Rafael J. Wysocki's system boot log,

I found a funny printout:

Node 0: aperture @ de000000 size 32 MB
Aperture too small (32 MB)
AGP bridge at 00:04:00
Aperture from AGP @ de000000 size 4096 MB (APSIZE 0)
Aperture too small (0 MB)
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000

...

agpgart: Detected AGP bridge 20
agpgart: Aperture pointing to RAM
agpgart: Aperture from AGP @ de000000 size 4096 MB
agpgart: Aperture too small (0 MB)
agpgart: No usable aperture found.
agpgart: Consider rebooting with iommu=memaper=2 to get a good aperture.

it means BIOS allocated the correct gart on the NB and AGP bridge, but
because a bug in the silicon (the agp bridge reports the wrong order,
it wants 4G instead) the kernel will reject that allocation.

Also, because the size is only 32MB, and we try to get another 64M for gart,
late fix_northbridge can not revert that change because it still reads
the wrong size from agp bridge.

So try to double check the order value from the agp bridge, before calling
aperture_valid().

[ mingo@elte.hu: 32-bit fix. ]

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

x86: iommu: use symbolic constants, not hardcoded numbers

Move symbolic constants into gart.h, and use them instead of hardcoded
constant.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

x86 gart: rename CONFIG_IOMMU to CONFIG_GART_IOMMU

This patch renames the IOMMU config option to GART_IOMMU because in fact it
means the GART and not general support for an IOMMU on x86.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

PCI: Change all drivers to use pci_device->revision

Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.

This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.

In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.

Compile tested with make all{yes,mod}config on x86_64 and i386.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

x86_64: off-by-two error in aperture.c

I'm using a custom BIOS to configure the northbridge GART at address
0x80000000, size 2G. Linux complains:

"Aperture from northbridge cpu 0 beyond 4GB. Ignoring."

I think there's an off-by-two error in arch/x86_64/kernel/aperture.c:

AK: use correct types for i386

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

[PATCH] x86: fix amd64-agp aperture validation

Under CONFIG_DISCONTIGMEM, assuming that a !pfn_valid() implies all
subsequent pfn-s are also invalid is wrong. Thus replace this by
explicitly checking against the E820 map.

AK: make e820 on x86-64 not initdata

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Mark Langsdorf <mark.langsdorf@amd.com>

[AGPGART] Further constification.

Make agp_bridge_driver->aperture_sizes and ->masks const.
Also agp_bridge_data->driver

Signed-off-by: Dave Jones <davej@redhat.com>

[AGPGART] Allow drm-populated agp memory types

This patch allows drm to populate an agpgart structure with pages of its own.
It's needed for the new drm memory manager which dynamically flips pages in and out of AGP.

The patch modifies the generic functions as well as the intel agp driver. The intel drm driver is
currently the only one supporting the new memory manager.

Other agp drivers may need some minor fixing up once they have a corresponding memory manager enabled drm driver.

AGP memory types >= AGP_USER_TYPES are not populated by the agpgart driver, but the drm is expected
to do that, as well as taking care of cache- and tlb flushing when needed.

It's not possible to request these types from user space using agpgart ioctls.

The Intel driver also gets a new memory type for pages that can be bound cached to the intel GTT.

Signed-off-by: Thomas Hellstrom <thomas@tungstengraphics.com>
Signed-off-by: Dave Jones <davej@redhat.com>

[AGPGART] Add new IDs to VIA AGP.

Culled from the VIA codedrop.
Also fixes up one ID used in amd64-agp to use the
VIA part number instead of the board name in its ID.

Signed-off-by: Dave Jones <davej@redhat.com>

[AGPGART] K8M890 support for amd-k8.

Signed-off-by: Dave Jones <davej@redhat.com>

[AGPGART] agp-amd64: section mismatches with HOTPLUG=n

When CONFIG_HOTPLUG=n, agp_amd64_resume() calls nforce3_agp_init(),
which is __devinit == __init, so has been discarded and is not
usable for resume.

WARNING: drivers/char/agp/amd64-agp.o - Section mismatch: reference to .init.text: from .text between 'agp_amd64_resume' (at offset 0x249) and 'amd64_tlbflush'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Dave Jones <davej@redhat.com>

[PATCH] agp-amd64: section mismatches with HOTPLUG=n

When CONFIG_HOTPLUG=n, agp_amd64_resume() calls nforce3_agp_init(), which is
__devinit == __init, so has been discarded and is not usable for resume.

WARNING: drivers/char/agp/amd64-agp.o - Section mismatch: reference to .init.text: from .text between 'agp_amd64_resume' (at offset 0x249) and 'amd64_tlbflush'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[AGPGART] Use pci_get_slot not pci_find_slot

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>

Remove obsolete #include <linux/config.h>

Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

[PATCH] x86_64: Rename IOMMU option, fix help and mark option embedded.

- Rename the GART_IOMMU option to IOMMU to make clear it's not
just for AMD
- Rewrite the help text to better emphatise this fact
- Make it an embedded option because too many people get it wrong.

To my astonishment I discovered the aacraid driver tests this
symbol directly. This looks quite broken to me - it's an internal
implementation detail of the PCI DMA API. Can the maintainer
please clarify what this test was intended to do?

Cc: linux-scsi@vger.kernel.org
Cc: alan@redhat.com
Cc: markh@osdl.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] x86_64: Clean and enhance up K8 northbridge access code

- Factor out the duplicated access/cache code into a single file
* Shared between i386/x86-64.
- Share flush code between AGP and IOMMU
* Fix a bug: AGP didn't wait for end of flush before
- Drop 8 northbridges limit and allocate dynamically
- Add lock to serialize AGP and IOMMU GART flushes
- Add PCI ID for next AMD northbridge
- Random related cleanups

The old K8 NUMA discovery code is unchanged. New systems
should all use SRAT for this.

Cc: "Navin Boppuri" <navin.boppuri@newisys.com>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[AGPGART] Fix pci_register_driver checking in amd64-agp

pci_register_driver() never returns a positive number.

Signed-off-by: Dave Jones <davej@redhat.com>

[AGPGART] Fix Nforce3 suspend on amd64.

kernel.org bugzilla #6206

Based on patch from Serge Belyshev <belyshev@depni.sinp.msu.ru>
Signed-off-by: Dave Jones <davej@redhat.com>

[PATCH] x86_64: Fix wrong PCI ID for ALI M1695 AGP bridge

[description by AK]
Made a cut'n'paste error when adding the entry for the ALI M1695
AGP bridge and added a second entry for the 1689

Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[AGPGART] x86_64: Fix wrong PCI ID for ALI M1695 AGP bridge

[description by AK]
Made a cut'n'paste error when adding the entry for the ALI M1695
AGP bridge and added a second entry for the 1689

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>

[AGPGART] Lots of CodingStyle/whitespace cleanups.

Eliminate trailing whitespace.
s/if(/if (/
s/for(/for (/

Signed-off-by: Dave Jones <davej@redhat.com>

[AGPGART] Add some informational printk to nforce GART failure path.

Signed-off-by: Dave Jones <davej@redhat.com>

[AGPGART] Suspend/Resume support for AMD64 GART.

This adds support for suspend/resume to the amd64-agp driver. Without
it, X displays garbage after resume from swsusp.

Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>

[AGPGART] Mark AMD64 aperture size structs as const

Neither of them are ever written to.

Noted by Arjan van de Ven
Signed-off-by: Dave Jones <davej@redhat.com>

[PATCH] AGP: Make gart iterator in K8 AGP driver SMP safe

Ugh!

Cc: davej@redhat.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] AGP: Try unsupported AGP chipsets on x86-64 by default

So far all new ones have worked and there isn't much variation because
the CPU does all the interesting bits.

So enable try unsupported by default.

Can be still disabled with try_unsupported=0 (module) or
amd64.try_unsupported=0 (boot option)

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] AGP: Support ULI/ALI 1689 bridge on AMD64

(no name because I'm not sure of the correct name)

Cc: davej@redhat.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] PCI: removed unneeded .owner field from struct pci_driver

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[PATCH] fix remaining missing includes

Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.

Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] fix missing includes

I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.

In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.

Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[AGPGART] Set .owner field of struct pci_driver.

From: Laurent Riffard <laurent.riffard@free.fr>

This updates .owner field of struct pci_driver.

This allows SYSFS to create the symlink from the driver to the module which
provides it.

$ tree /sys/bus/pci/drivers/agpgart-via/
/sys/bus/pci/drivers/agpgart-via/
|-- 0000:00:00.0 -> ../../../../devices/pci0000:00/0000:00:00.0
|-- bind
|-- module -> ../../../../module/via_agp
|-- new_id
`-- unbind

Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>

[AGPGART] Remove trailing space before \n

From: Denis Vlasenko <vda@ilport.com.ua>
Signed-off-by: Dave Jones <davej@redhat.com>

[PATCH] sis 760 support.

This patch adds the SiS 760 ID to the amd64-agp driver, so that agpgart can be
used on Athlon64 boards based on this chip.

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] AGP fix for Xen VMM

When Linux is running on the Xen virtual machine monitor, physical
addresses are virtualised and cannot be directly referenced by the AGP
GART. This patch fixes the GART driver for Xen by adding a layer of
abstraction between physical addresses and 'GART addresses'.

Architecture-specific functions are also defined for allocating and freeing
the GATT. Xen requires this to ensure that table really is contiguous from
the point of view of the GART.

These extra interface functions are defined as 'no-ops' for all existing
architectures that use the GART driver.

Signed-off-by: Keir Fraser <keir@xensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>

[PATCH] make lots of things static

Another large rollup of various patches from Adrian which make things static
where they were needlessly exported.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!