License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arch/sparc: Avoid DCTI Couples

Avoid un-intended DCTI Couples. Use of DCTI couples is deprecated.
Also address the "Programming Note" for optimal performance.

Here is the complete text from Oracle SPARC Architecture Specs.

6.3.4.7 DCTI Couples
"A delayed control transfer instruction (DCTI) in the delay slot of
another DCTI is referred to as a “DCTI couple”. The use of DCTI couples
is deprecated in the Oracle SPARC Architecture; no new software should
place a DCTI in the delay slot of another DCTI, because on future Oracle
SPARC Architecture implementations DCTI couples may execute either
slowly or differently than the programmer assumes it will.

SPARC V8 and SPARC V9 Compatibility Note
The SPARC V8 architecture left behavior undefined for a DCTI couple. The
SPARC V9 architecture defined behavior in that case, but as of
UltraSPARC Architecture 2005, use of DCTI couples was deprecated.
Software should not expect high performance from DCTI couples, and
performance of DCTI couples should be expected to decline further in
future processors.

Programming Note
As noted in TABLE 6-5 on page 115, an annulled branch-always
(branch-always with a = 1) instruction is not architecturally a DCTI.
However, since not all implementations make that distinction, for
optimal performance, a DCTI should not be placed in the instruction word
immediately following an annulled branch-always instruction (BA,A or
BPA,A)."

Signed-off-by: Babu Moger <babu.moger@oracle.com>
Reviewed-by: Rob Gardner <rob.gardner@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sparc64: sun4v TLB error power off events

We've witnessed a few TLB events causing the machine to power off because
of prom_halt. In one case it was some nfs related area during rmmod. Another
was an mmapper of /dev/mem. A more recent one is an ITLB issue with
a bad pagesize which could be a hardware bug. Bugs happen but we should
attempt to not power off the machine and/or hang it when possible.

This is a DTLB error from an mmapper of /dev/mem:
[root@sparcie ~]# SUN4V-DTLB: Error at TPC[fffff80100903e6c], tl 1
SUN4V-DTLB: TPC<0xfffff80100903e6c>
SUN4V-DTLB: O7[fffff801081979d0]
SUN4V-DTLB: O7<0xfffff801081979d0>
SUN4V-DTLB: vaddr[fffff80100000000] ctx[1250] pte[98000000000f0610] error[2]
.

This is recent mainline for ITLB:
[ 3708.179864] SUN4V-ITLB: TPC<0xfffffc010071cefc>
[ 3708.188866] SUN4V-ITLB: O7[fffffc010071cee8]
[ 3708.197377] SUN4V-ITLB: O7<0xfffffc010071cee8>
[ 3708.206539] SUN4V-ITLB: vaddr[e0003] ctx[1a3c] pte[2900000dcc800eeb] error[4]
.

Normally sun4v_itlb_error_report() and sun4v_dtlb_error_report() would call
prom_halt() and drop us to OF command prompt "ok". This isn't the case for
LDOMs and the machine powers off.

For the HV reported error of HV_ENORADDR for HV HV_MMU_MAP_ADDR_TRAP we cause
a SIGBUS error by qualifying it within do_sparc64_fault() for fault code mask
of FAULT_CODE_BAD_RA. This is done when trap level (%tl) is less or equal
one("1"). Otherwise, for %tl > 1, we proceed eventually to die_if_kernel().

The logic of this patch was partially inspired by David Miller's feedback.

Power off of large sparc64 machines is painful. Plus die_if_kernel provides
more context. A reset sequence isn't a brief period on large sparc64 but
better than power-off/power-on sequence.

Cc: sparclinux@vger.kernel.org
Signed-off-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sparc64: Move from 4MB to 8MB huge pages.

The impetus for this is that we would like to move to 64-bit PMDs and
PGDs, but that would result in only supporting a 42-bit address space
with the current page table layout. It'd be nice to support at least
43-bits.

The reason we'd end up with only 42-bits after making PMDs and PGDs
64-bit is that we only use half-page sized PTE tables in order to make
PMDs line up to 4MB, the hardware huge page size we use.

So what we do here is we make huge pages 8MB, and fabricate them using
4MB hw TLB entries.

Facilitate this by providing a "REAL_HPAGE_SHIFT" which is used in
places that really need to operate on hardware 4MB pages.

Use full pages (512 entries) for PTE tables, and adjust PMD_SHIFT,
PGD_SHIFT, and the build time CPP test as needed. Use a CPP test to
make sure REAL_HPAGE_SHIFT and the _PAGE_SZHUGE_* we use match up.

This makes the pgtable cache completely unused, so remove the code
managing it and the state used in mm_context_t. Now we have less
spinlocks taken in the page table allocation path.

The technique we use to fabricate the 8MB pages is to transfer bit 22
from the missing virtual address into the PTEs physical address field.
That takes care of the transparent huge pages case.

For hugetlb, we fill things in at the PTE level and that code already
puts the sub huge page physical bits into the PTEs, based upon the
offset, so there is nothing special we need to do. It all just works
out.

So, a small amount of complexity in the THP case, but this code is
about to get much simpler when we move the 64-bit PMDs as we can move
away from the fancy 32-bit huge PMD encoding and just put a real PTE
value in there.

With bug fixes and help from Bob Picco.

Signed-off-by: David S. Miller <davem@davemloft.net>

sparc64: Support transparent huge pages.

This is relatively easy since PMD's now cover exactly 4MB of memory.

Our PMD entries are 32-bits each, so we use a special encoding. The
lowest bit, PMD_ISHUGE, determines the interpretation. This is possible
because sparc64's page tables are purely software entities so we can use
whatever encoding scheme we want. We just have to make the TLB miss
assembler page table walkers aware of the layout.

set_pmd_at() works much like set_pte_at() but it has to operate in two
page from a table of non-huge PTEs, so we have to queue up TLB flushes
based upon what mappings are valid in the PTE table. In the second regime
we are going from huge-page to non-huge-page, and in that case we need
only queue up a single TLB flush to push out the huge page mapping.

We still have 5 bits remaining in the huge PMD encoding so we can very
likely support any new pieces of THP state tracking that might get added
in the future.

With lots of help from Johannes Weiner.

Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sparc,sparc64: unify kernel/

o Move all files from sparc64/kernel/ to sparc/kernel
- rename as appropriate
o Update sparc/Makefile to the changes
o Update sparc/kernel/Makefile to include the sparc64 files

NOTE: This commit changes link order on sparc64!

Link order had to change for either of sparc32 and sparc64.
And assuming sparc64 see more testing than sparc32 change link
order on sparc64 where issues will be caught faster.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>