KVM: PPC: Reduce reliance on analyse_instr() in mmio emulation

Commit 709236039964 ("KVM: PPC: Reimplement non-SIMD LOAD/STORE
instruction mmio emulation with analyse_instr() input") and
commit 2b33cb585f94 ("KVM: PPC: Reimplement LOAD_FP/STORE_FP instruction
mmio emulation with analyse_instr() input") made
kvmppc_emulate_loadstore() use the results from analyse_instr() for
instruction emulation. In particular the effective address from
analyse_instr() is used for UPDATE type instructions and fact that
op.val is all ready endian corrected is used in the STORE case.

However, these changes now have some negative implications for the
nestedv2 case. For analyse_instr() to determine the correct effective
address, the GPRs must be loaded from the L0. This is not needed as
vcpu->arch.vaddr_accessed is already set. Change back to using
vcpu->arch.vaddr_accessed.

In the STORE case, use kvmppc_get_gpr() value instead of the op.val.
kvmppc_get_gpr() will reload from the L0 if needed in the nestedv2 case.
This means if a byte reversal is needed must now be passed to
kvmppc_handle_store() like in the kvmppc_handle_load() case.

This means the call to kvmhv_nestedv2_reload_ptregs() can be avoided as
there is no concern about op.val being stale. Drop the call to
kvmhv_nestedv2_mark_dirty_ptregs() as without the call to
kvmhv_nestedv2_reload_ptregs(), stale state could be marked as valid.

This is fine as the required marking things dirty is already handled for
the UPDATE case by the call to kvmppc_set_gpr(). For LOADs, it is
handled in kvmppc_complete_mmio_load(). This is called either directly
in __kvmppc_handle_load() if the load can be handled in KVM, or on the
next kvm_arch_vcpu_ioctl_run() if an exit was required.

Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20231201132618.555031-12-vaibhav@linux.ibm.com

KVM: PPC: Add support for nestedv2 guests

A series of hcalls have been added to the PAPR which allow a regular
guest partition to create and manage guest partitions of its own. KVM
already had an interface that allowed this on powernv platforms. This
existing interface will now be called "nestedv1". The newly added PAPR
interface will be called "nestedv2". PHYP will support the nestedv2
interface. At this time the host side of the nestedv2 interface has not
been implemented on powernv but there is no technical reason why it
could not be added.

The nestedv1 interface is still supported.

Add support to KVM to utilize these hcalls to enable running nested
guests as a pseries guest on PHYP.

Overview of the new hcall usage:

- L1 and L0 negotiate capabilities with
H_GUEST_{G,S}ET_CAPABILITIES()

- L1 requests the L0 create a L2 with
H_GUEST_CREATE() and receives a handle to use in future hcalls

- L1 requests the L0 create a L2 vCPU with
H_GUEST_CREATE_VCPU()

- L1 sets up the L2 using H_GUEST_SET and the
H_GUEST_VCPU_RUN input buffer

- L1 requests the L0 runs the L2 vCPU using H_GUEST_VCPU_RUN()

- L2 returns to L1 with an exit reason and L1 reads the
H_GUEST_VCPU_RUN output buffer populated by the L0

- L1 handles the exit using H_GET_STATE if necessary

- L1 reruns L2 vCPU with H_GUEST_VCPU_RUN

- L1 frees the L2 in the L0 with H_GUEST_DELETE()

Support for the new API is determined by trying
H_GUEST_GET_CAPABILITIES. On a successful return, use the nestedv2
interface.

Use the vcpu register state setters for tracking modified guest state
elements and copy the thread wide values into the H_GUEST_VCPU_RUN input
buffer immediately before running a L2. The guest wide
elements can not be added to the input buffer so send them with a
separate H_GUEST_SET call if necessary.

Make the vcpu register getter load the corresponding value from the real
host with H_GUEST_GET. To avoid unnecessarily calling H_GUEST_GET, track
which values have already been loaded between H_GUEST_VCPU_RUN calls. If
an element is present in the H_GUEST_VCPU_RUN output buffer it also does
not need to be loaded again.

Tested-by: Sachin Sant <sachinp@linux.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Signed-off-by: Gautam Menghani <gautam@linux.ibm.com>
Signed-off-by: Kautuk Consul <kconsul@linux.vnet.ibm.com>
Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com>
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230914030600.16993-11-jniethe5@gmail.com

KVM: PPC: Introduce FPR/VR accessor functions

Introduce accessor functions for floating point and vector registers
like the ones that exist for GPRs. Use these to replace the existing FPR
and VR accessor macros.

This will be important later for Nested APIv2 support which requires
additional functionality for accessing and modifying VCPU state.

Signed-off-by: Gautam Menghani <gautam@linux.ibm.com>
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230914030600.16993-3-jniethe5@gmail.com

KVM: PPC: Fetch prefixed instructions from the guest

In order to handle emulation of prefixed instructions in the guest,
this first makes vcpu->arch.last_inst be an unsigned long, i.e. 64
bits on 64-bit platforms. For prefixed instructions, the upper 32
bits are used for the prefix and the lower 32 bits for the suffix, and
both halves are byte-swapped if the guest endianness differs from the
host.

Next, vcpu->arch.emul_inst is now 64 bits wide, to match the HEIR
register on POWER10. Like HEIR, for a prefixed instruction it is
defined to have the prefix is in the top 32 bits and the suffix in the
bottom 32 bits, with both halves in the correct byte order.

kvmppc_get_last_inst is extended on 64-bit machines to put the prefix
and suffix in the right places in the ppc_inst_t being returned.

kvmppc_load_last_inst now returns the instruction in an unsigned long
in the same format as vcpu->arch.last_inst. It makes the decision
about whether to fetch a suffix based on the SRR1_PREFIXED bit in the
MSR image stored in the vcpu struct, which generally comes from SRR1
or HSRR1 on an interrupt. This bit is defined in Power ISA v3.1B to
be set if the interrupt occurred due to a prefixed instruction and
cleared otherwise for all interrupts except for instruction storage
interrupt, which does not come to the hypervisor. It is set to zero
for asynchronous interrupts such as external interrupts. In previous
ISA versions it was always set to 0 for all interrupts except
instruction storage interrupt.

The code in book3s_hv_rmhandlers.S that loads the faulting instruction
on a HDSI is only used on POWER8 and therefore doesn't ever need to
load a suffix.

[npiggin@gmail.com - check that the is-prefixed bit in SRR1 matches the
type of instruction that was fetched.]

Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/ZAgsq9h1CCzouQuV@cleo

KVM: PPC: Make kvmppc_get_last_inst() produce a ppc_inst_t

This changes kvmppc_get_last_inst() so that the instruction it fetches
is returned in a ppc_inst_t variable rather than a u32. This will
allow us to return a 64-bit prefixed instruction on those 64-bit
machines that implement Power ISA v3.1 or later, such as POWER10.
On 32-bit platforms, ppc_inst_t is 32 bits wide, and is turned back
into a u32 by ppc_inst_val, which is an identity operation on those
platforms.

Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/ZAgsiPlL9O7KnlZZ@cleo

KVM: PPC: Book3S HV: Set SRR1[PREFIX] bit on injected interrupts

Pass the hypervisor (H)SRR1[PREFIX] indication through to synchronous
interrupts injected into the guest.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230330103224.3589928-3-npiggin@gmail.com

KVM: PPC: Permit SRR1 flags in more injected interrupt types

The prefix architecture in ISA v3.1 introduces a prefixed bit in SRR1
for many types of synchronous interrupts which is set when the interrupt
is caused by a prefixed instruction.

This requires KVM to be able to set this bit when injecting interrupts
into a guest. Plumb through the SRR1 "flags" argument to the core_queue
APIs where it's missing for this. For now they are set to 0, which is
no change.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fixup kvmppc_core_queue_alignment() in booke.c]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230330103224.3589928-2-npiggin@gmail.com

KVM: PPC: Book3s: mmio: Deliver DSI after emulation failure

MMIO emulation can fail if the guest uses an instruction that we are
not prepared to emulate. Since these instructions can be and most
likely are valid ones, this is (slightly) closer to an access fault
than to an illegal instruction, so deliver a Data Storage interrupt
instead of a Program interrupt.

BookE ignores bad faults, so it will keep using a Program interrupt
because a DSI would cause a fault loop in the guest.

Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220125215655.1026224-6-farosas@linux.ibm.com

KVM: PPC: Clean up redundant 'kvm_run' parameters

In the current kvm version, 'kvm_run' has been included in the 'kvm_vcpu'
structure. For historical reasons, many kvm-related function parameters
retain the 'kvm_run' and 'kvm_vcpu' parameters at the same time. This
patch does a unified cleanup of these remaining redundant parameters.

Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

powerpc: Use a macro for creating instructions from u32s

In preparation for instructions having a more complex data type start
using a macro, ppc_inst(), for making an instruction out of a u32. A
macro is used so that instructions can be used as initializer elements.
Currently this does nothing, but it will allow for creating a data type
that can represent prefixed instructions.

Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
[mpe: Change include guard to _ASM_POWERPC_INST_H]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-7-jniethe5@gmail.com

KVM: PPC: Remove set but not used variable 'ra', 'rs', 'rt'

Fixes gcc '-Wunused-but-set-variable' warning:

arch/powerpc/kvm/emulate_loadstore.c: In function kvmppc_emulate_loadstore:
arch/powerpc/kvm/emulate_loadstore.c:87:6: warning: variable ra set but not used [-Wunused-but-set-variable]
arch/powerpc/kvm/emulate_loadstore.c: In function kvmppc_emulate_loadstore:
arch/powerpc/kvm/emulate_loadstore.c:87:10: warning: variable rs set but not used [-Wunused-but-set-variable]
arch/powerpc/kvm/emulate_loadstore.c: In function kvmppc_emulate_loadstore:
arch/powerpc/kvm/emulate_loadstore.c:87:14: warning: variable rt set but not used [-Wunused-but-set-variable]

They are not used since commit 2b33cb585f94 ("KVM: PPC: Reimplement
LOAD_FP/STORE_FP instruction mmio emulation with analyse_instr() input")

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

KVM: PPC: Remove leftover comment from emulate_loadstore.c

Commit 4eeb85568e56 ("KVM: PPC: Remove mmio_vsx_tx_sx_enabled in KVM
MMIO emulation") removed the mmio_vsx_tx_sx_enabled field, but its
documentation was left behind. Remove the superfluous comment.

Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 266

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation 51 franklin street fifth floor boston ma 02110
1301 usa

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 67 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141333.953658117@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: PPC: Use ccr field in pt_regs struct embedded in vcpu struct

When the 'regs' field was added to struct kvm_vcpu_arch, the code
was changed to use several of the fields inside regs (e.g., gpr, lr,
etc.) but not the ccr field, because the ccr field in struct pt_regs
is 64 bits on 64-bit platforms, but the cr field in kvm_vcpu_arch is
only 32 bits. This changes the code to use the regs.ccr field
instead of cr, and changes the assembly code on 64-bit platforms to
use 64-bit loads and stores instead of 32-bit ones.

Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

KVM: PPC: Remove mmio_vsx_tx_sx_enabled in KVM MMIO emulation

Originally PPC KVM MMIO emulation uses only 0~31#(5 bits) for VSR
reg number, and use mmio_vsx_tx_sx_enabled field together for
0~63# VSR regs.

Currently PPC KVM MMIO emulation is reimplemented with analyse_instr()
assistance. analyse_instr() returns 0~63 for VSR register number, so
it is not necessary to use additional mmio_vsx_tx_sx_enabled field
any more.

This patch extends related reg bits (expand io_gpr to u16 from u8
and use 6 bits for VSR reg#), so that mmio_vsx_tx_sx_enabled can
be removed.

Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

KVM: PPC: Reimplement LOAD_VMX/STORE_VMX instruction mmio emulation with analyse_instr() input

This patch reimplements LOAD_VMX/STORE_VMX MMIO emulation with
analyse_instr() input. When emulating the store, the VMX reg will need to
be flushed so that the right reg val can be retrieved before writing to
IO MEM.

This patch also adds support for lvebx/lvehx/lvewx/stvebx/stvehx/stvewx
MMIO emulation. To meet the requirement of handling different element
sizes, kvmppc_handle_load128_by2x64()/kvmppc_handle_store128_by2x64()
were replaced with kvmppc_handle_vmx_load()/kvmppc_handle_vmx_store().

The framework used is similar to VSX instruction MMIO emulation.

Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

KVM: PPC: Expand mmio_vsx_copy_type to cover VMX load/store element types

VSX MMIO emulation uses mmio_vsx_copy_type to represent VSX emulated
element size/type, such as KVMPPC_VSX_COPY_DWORD_LOAD, etc. This
patch expands mmio_vsx_copy_type to cover VMX copy type, such as
KVMPPC_VMX_COPY_BYTE(stvebx/lvebx), etc. As a result,
mmio_vsx_copy_type is also renamed to mmio_copy_type.

It is a preparation for reimplementing VMX MMIO emulation.

Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

KVM: PPC: Reimplement LOAD_VSX/STORE_VSX instruction mmio emulation with analyse_instr() input

This patch reimplements LOAD_VSX/STORE_VSX instruction MMIO emulation with
analyse_instr() input. It utilizes VSX_FPCONV/VSX_SPLAT/SIGNEXT exported
by analyse_instr() and handle accordingly.

When emulating VSX store, the VSX reg will need to be flushed so that
the right reg val can be retrieved before writing to IO MEM.

[paulus@ozlabs.org - mask the register number to 5 bits.]

Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

KVM: PPC: Reimplement LOAD_FP/STORE_FP instruction mmio emulation with analyse_instr() input

This patch reimplements LOAD_FP/STORE_FP instruction MMIO emulation with
analyse_instr() input. It utilizes the FPCONV/UPDATE properties exported by
analyse_instr() and invokes kvmppc_handle_load(s)/kvmppc_handle_store()
accordingly.

For FP store MMIO emulation, the FP regs need to be flushed firstly so
that the right FP reg vals can be read from vcpu->arch.fpr, which will
be stored into MMIO data.

Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

KVM: PPC: Reimplement non-SIMD LOAD/STORE instruction mmio emulation with analyse_instr() input

This patch reimplements non-SIMD LOAD/STORE instruction MMIO emulation
with analyse_instr() input. It utilizes the BYTEREV/UPDATE/SIGNEXT
properties exported by analyse_instr() and invokes
kvmppc_handle_load(s)/kvmppc_handle_store() accordingly.

It also moves CACHEOP type handling into the skeleton.

instruction_type within kvm_ppc.h is renamed to avoid conflict with
sstep.h.

Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

KVM: PPC: Fix a mmio_host_swabbed uninitialized usage issue

When KVM emulates VMX store, it will invoke kvmppc_get_vmx_data() to
retrieve VMX reg val. kvmppc_get_vmx_data() will check mmio_host_swabbed
to decide which double word of vr[] to be used. But the
mmio_host_swabbed can be uninitialized during VMX store procedure:

kvmppc_emulate_loadstore
\- kvmppc_handle_store128_by2x64
\- kvmppc_get_vmx_data

So vcpu->arch.mmio_host_swabbed is not meant to be used at all for
emulation of store instructions, and this patch makes that true for
VMX stores. This patch also initializes mmio_host_swabbed to avoid
possible future problems.

Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

KVM: PPC: Book3S: Add MMIO emulation for VMX instructions

This patch provides the MMIO load/store vector indexed
X-Form emulation.

Instructions implemented:
lvx: the quadword in storage addressed by the result of EA &
0xffff_ffff_ffff_fff0 is loaded into VRT.

stvx: the contents of VRS are stored into the quadword in storage
addressed by the result of EA & 0xffff_ffff_ffff_fff0.

Reported-by: Gopesh Kumar Chaudhary <gopchaud@in.ibm.com>
Reported-by: Balamuruhan S <bala24@linux.vnet.ibm.com>
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

KVM: PPC: Add MMIO emulation for remaining floating-point instructions

For completeness, this adds emulation of the lfiwax and lfiwzx
instructions. With this, all floating-point load and store instructions
as of Power ISA V2.07 are emulated.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

KVM: PPC: Emulation for more integer loads and stores

This adds emulation for the following integer loads and stores,
thus enabling them to be used in a guest for accessing emulated
MMIO locations.

- lhaux
- lwaux
- lwzux
- ldu
- lwa
- stdux
- stwux
- stdu
- ldbrx
- stdbrx

Previously, most of these would cause an emulation failure exit to
userspace, though ldu and lwa got treated incorrectly as ld, and
stdu got treated incorrectly as std.

This also tidies up some of the formatting and updates the comment
listing instructions that still need to be implemented.

With this, all integer loads and stores that are defined in the Power
ISA v2.07 are emulated, except for those that are permitted to trap
when used on cache-inhibited or write-through mappings (and which do
in fact trap on POWER8), that is, lmw/stmw, lswi/stswi, lswx/stswx,
lq/stq, and l[bhwdq]arx/st[bhwdq]cx.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

KVM: PPC: Add MMIO emulation for stdx (store doubleword indexed)

This adds missing stdx emulation for emulated MMIO accesses by KVM
guests. This allows the Mellanox mlx5_core driver from recent kernels
to work when MMIO emulation is enforced by userspace.

Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

KVM: PPC: Book3S: Add MMIO emulation for FP and VSX instructions

This patch provides the MMIO load/store emulation for instructions
of 'double & vector unsigned char & vector signed char & vector
unsigned short & vector signed short & vector unsigned int & vector
signed int & vector double '.

The instructions that this adds emulation for are:

- ldx, ldux, lwax,
- lfs, lfsx, lfsu, lfsux, lfd, lfdx, lfdu, lfdux,
- stfs, stfsx, stfsu, stfsux, stfd, stfdx, stfdu, stfdux, stfiwx,
- lxsdx, lxsspx, lxsiwax, lxsiwzx, lxvd2x, lxvw4x, lxvdsx,
- stxsdx, stxsspx, stxsiwx, stxvd2x, stxvw4x

[paulus@ozlabs.org - some cleanups, fixes and rework, make it
compile for Book E, fix build when PR KVM is built in]

Signed-off-by: Bin Lu <lblulb@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>

KVM: PPC: Pass enum to kvmppc_get_last_inst

The kvmppc_get_last_inst function recently received a facelift that allowed
us to pass an enum of the type of instruction we want to read into it rather
than an unreadable boolean.

Unfortunately, not all callers ended up passing the enum. This wasn't really
an issue as "true" and "false" happen to match the two enum values we have,
but it's still hard to read.

Update all callers of kvmppc_get_last_inst() to follow the new calling
convention.

Signed-off-by: Alexander Graf <agraf@suse.de>

KVM: PPC: Separate loadstore emulation from priv emulation

Today the instruction emulator can get called via 2 separate code paths. It
can either be called by MMIO emulation detection code or by privileged
instruction traps.

This is bad, as both code paths prepare the environment differently. For MMIO
emulation we already know the virtual address we faulted on, so instructions
there don't have to actually fetch that information.

Split out the two separate use cases into separate files.

Signed-off-by: Alexander Graf <agraf@suse.de>