powerpc: Add missing headers

Don't inherit headers "by chances" from asm/prom.h, asm/mpc52xx.h,
asm/pci.h etc...

Include the needed headers, and remove asm/prom.h when it was
needed exclusively for pulling necessary headers.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/be8bdc934d152a7d8ee8d1a840d5596e2f7d85e0.1646767214.git.christophe.leroy@csgroup.eu

powerpc: fix typos in comments

Various spelling mistakes in comments.
Detected with the help of Coccinelle.

Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220430185654.5855-1-Julia.Lawall@inria.fr

powerpc/pci: Remove pcibios_setup_bus_devices()

With the previous patch applied pcibios_setup_device() will always be run
when pcibios_bus_add_device() is called. There are several code paths where
pcibios_setup_bus_device() is still called (the PowerPC specific PCI
hotplug support is one) so with just the previous patch applied the setup
can be run multiple times on a device, once before the device is added
to the bus and once after.

There's no need to run the setup in the early case any more so just
remove it entirely.

Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191028085424.12006-3-oohall@gmail.com

powerpc/of/pci: Rewrite pci_parse_of_flags

The existing code uses bunch of hardcoded values from the PCI Bus
Binding to IEEE Std 1275 spec; and it does so in quite non-obvious
way.

This defines fields from the cell#0 of the "reg" property of a PCI
device and uses them for parsing.

This should cause no behavioral change.

Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[mpe: Unsplit some 80/81 char lines, space the code with some newlines]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190829084417.71873-1-aik@ozlabs.ru

powerpc/pci/of: Parse unassigned resources

The pseries platform uses the PCI_PROBE_DEVTREE method of PCI probing
which reads "assigned-addresses" of every PCI device and initializes
the device resources. However if the property is missing or zero sized,
then there is no fallback of any kind and the PCI resources remain
undiscovered, i.e. pdev->resource[] array remains empty.

This adds a fallback which parses the "reg" property in pretty much same
way except it marks resources as "unset" which later make Linux assign
those resources proper addresses.

This has an effect when:
1. a hypervisor failed to assign any resource for a device;
2. /chosen/linux,pci-probe-only=0 is in the DT so the system may try
assigning a resource.
Neither is likely to happen under PowerVM.

Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/pci/of: Fix OF flags parsing for 64bit BARs

When the firmware does PCI BAR resource allocation, it passes the assigned
addresses and flags (prefetch/64bit/...) via the "reg" property of
a PCI device device tree node so the kernel does not need to do
resource allocation.

The flags are stored in resource::flags - the lower byte stores
PCI_BASE_ADDRESS_SPACE/etc bits and the other bytes are IORESOURCE_IO/etc.
Some flags from PCI_BASE_ADDRESS_xxx and IORESOURCE_xxx are duplicated,
such as PCI_BASE_ADDRESS_MEM_PREFETCH/PCI_BASE_ADDRESS_MEM_TYPE_64/etc.
When parsing the "reg" property, we copy the prefetch flag but we skip
on PCI_BASE_ADDRESS_MEM_TYPE_64 which leaves the flags out of sync.

The missing IORESOURCE_MEM_64 flag comes into play under 2 conditions:
1. we remove PCI_PROBE_ONLY for pseries (by hacking pSeries_setup_arch()
or by passing "/chosen/linux,pci-probe-only");
2. we request resource alignment (by passing pci=resource_alignment=
via the kernel cmd line to request PAGE_SIZE alignment or defining
ppc_md.pcibios_default_alignment which returns anything but 0). Note that
the alignment requests are ignored if PCI_PROBE_ONLY is enabled.

With 1) and 2), the generic PCI code in the kernel unconditionally
decides to:
- reassign the BARs in pci_specified_resource_alignment() (works fine)
- write new BARs to the device - this fails for 64bit BARs as the generic
code looks at IORESOURCE_MEM_64 (not set) and writes only lower 32bits
of the BAR and leaves the upper 32bit unmodified which breaks BAR mapping
in the hypervisor.

This fixes the issue by copying the flag. This is useful if we want to
enforce certain BAR alignment per platform as handling subpage sized BARs
is proven to cause problems with hotplug (SLOF already aligns BARs to 64k).

Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Shawn Anastasio <shawn@anastas.io>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500

Based on 2 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc: Use device_type helpers to access the node type

Remove directly accessing device_node.type pointer and use the
accessors instead. This will eventually allow removing the type
pointer.

Replace the open coded iterating over child nodes with
for_each_child_of_node() while we're here.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/pseries: Add Initialization of VF Bars

When enabling SR-IOV in pseries platform, the VF bar properties for a
PF are reported on the device node in the device tree.

This patch adds the IOV Bar resources to Linux structures from the
device tree for later use when configuring SR-IOV by PF driver.

Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@linux.vnet.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/pci: Use for_each_pci_bridge() helper

Use for_each_pci_bridge() helper to make the code slightly cleaner. No
functional change intended.

Requires: 24a0c654d7d6 ("PCI: Add for_each_pci_bridge() helper")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: Convert to using %pOF instead of full_name

Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linuxppc-dev@lists.ozlabs.org
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: Remove all usages of NO_IRQ

NO_IRQ has been == 0 on powerpc for just over ten years (since commit
0ebfff1491ef ("[POWERPC] Add new interrupt mapping core and change
platforms to use it")). It's also 0 on most other arches.

Although it's fairly harmless, every now and then it causes confusion
when a driver is built on powerpc and another arch which doesn't define
NO_IRQ. There's at least 6 definitions of NO_IRQ in drivers/, at least
some of which are to work around that problem.

So we'd like to remove it. This is fairly trivial in the arch code, we
just convert:

if (irq == NO_IRQ) to if (!irq)
if (irq != NO_IRQ) to if (irq)
irq = NO_IRQ; to irq = 0;
return NO_IRQ; to return 0;

And a few other odd cases as well.

At least for now we keep the #define NO_IRQ, because there is driver
code that uses NO_IRQ and the fixes to remove those will go via other
trees.

Note we also change some occurrences in PPC sound drivers, drivers/ps3,
and drivers/macintosh.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

PCI/MSI: Initialize MSI capability for all architectures

1851617cd2da ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't
support MSI") moved dev->msi_cap and dev->msix_cap initialization from the
pci_init_capabilities() path (used on all architectures) to the
pci_setup_device() path (not used on Open Firmware architectures).

This broke MSI or MSI-X on Open Firmware machines. 4d9aac397a5d
("powerpc/PCI: Disable MSI/MSI-X interrupts at PCI probe time in OF case")
fixed it for PowerPC but not for SPARC.

Set up MSI and MSI-X (initialize msi_cap and msix_cap and disable MSI and
MSI-X) in pci_init_capabilities() so all architectures do it the same way.

This reverts 4d9aac397a5d since this patch fixes the problem generically
for both PowerPC and SPARC.

[bhelgaas: changelog, make pci_msi_setup_pci_dev() static]
Fixes: 1851617cd2da ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

powerpc/PCI: Disable MSI/MSI-X interrupts at PCI probe time in OF case

Since commit 1851617cd2da ("PCI/MSI: Disable MSI at enumeration even if
kernel doesn't support MSI"), the setup of dev->msi_cap/msix_cap and the
disable of MSI/MSI-X interrupts isn't being done at PCI probe time, as
the logic responsible for this was moved in the aforementioned commit
from pci_device_add() to pci_setup_device(). The latter function is not
reachable on PowerPC pseries platform during Open Firmware PCI probing
time.

This exhibits as drivers not being able to enable MSI, eg:

bnx2x 0000:01:00.0: no msix capability found

This patch calls pci_msi_setup_pci_dev() explicitly to disable MSI/MSI-X
during PCI probe time on pSeries platform.

Fixes: 1851617cd2da ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Flesh out change log and clarify comment]
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

cleanup IORESOURCE_CACHEABLE vs ioremap()

Quoting Arnd:
I was thinking the opposite approach and basically removing all uses
of IORESOURCE_CACHEABLE from the kernel. There are only a handful of
them.and we can probably replace them all with hardcoded
ioremap_cached() calls in the cases they are actually useful.

All existing usages of IORESOURCE_CACHEABLE call ioremap() instead of
ioremap_nocache() if the resource is cacheable, however ioremap() is
uncached by default. Clearly none of the existing usages care about the
cacheability. Particularly devm_ioremap_resource() never worked as
advertised since it always fell back to plain ioremap().

Clean this up as the new direction we want is to convert
ioremap_<type>() usages to memremap(..., flags).

Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

PCI: Hold pci_slot_mutex while searching bus->slots list

Previously, pci_setup_device() and similar functions searched the
pci_bus->slots list without any locking. It was possible for another
thread to update the list while we searched it.

Add pci_dev_assign_slot() to search the list while holding pci_slot_mutex.

[bhelgaas: changelog, fold in CONFIG_SYSFS fix]
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

powerpc: Remove shims for pci_controller_ops operations

Remove shims, patch callsites to use pci_controller_ops
versions instead.

Also move back the probe mode defines, as explained in the patch
for pci_probe_mode.

Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: Create pci_controller_ops.probe_mode and shim

Add pci_controller_ops.probe_mode, shadowing ppc_md.pci_probe_mode.
Add a shim, and changes the callsites to use the shim.

We also need to move the probe mode defines to pci-bridge.h from pci.h.
They are required by the shim in order to return a sensible default.
Previously, the were defined in pci.h, but pci.h includes pci-bridge.h
before the relevant #defines. This means the definitions are absent
if pci.h is included before pci-bridge.h. This occurs in some drivers.
So, move the definitons now, and move them back when we remove the shim.

Anything that wants the defines would have had to include pci.h, and
since pci.h includes pci-bridge.h, nothing will lose access to the
defines.

Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/eeh: Remove device_node dependency

The patch removes struct eeh_dev::dn and the corresponding helper
functions: eeh_dev_to_of_node() and of_node_to_eeh_dev(). Instead,
eeh_dev_to_pdn() and pdn_to_eeh_dev() should be used to get the
pdn, which might contain device_node on PowerNV platform.

Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

powerpc: Make a bunch of things static

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/PCI: Use pci_is_bridge() to simplify code

Use pci_is_bridge() to simplify code. No functional change.

Requires: 326c1cdae741 PCI: Rename pci_is_bridge() to pci_has_subordinate()
Requires: 1c86438c9423 PCI: Add new pci_is_bridge() interface
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

powerpc/eeh: No hotplug on permanently removed dev

The issue was detected in a bit complicated test case where
we have multiple hierarchical PEs shown as following figure:

+-----------------+
| PE#3 p2p#0 |
| p2p#1 |
+-----------------+
|
+-----------------+
| PE#4 pdev#0 |
| pdev#1 |
+-----------------+

PE#4 (have 2 PCI devices) is the child of PE#3, which has 2 p2p
bridges. We accidentally had less-known scenario: PE#4 was removed
permanently from the system because of permanent failure (e.g.
exceeding the max allowd failure times in last hour), then we detects
EEH errors on PE#3 and tried to recover it. However, eeh_dev instances
for pdev#0/1 were not detached from PE#4, which was still connected to
PE#3. All of that was because of the fact that we rely on count-based
pcibios_release_device(), which isn't reliable enough. When doing
recovery for PE#3, we still apply hotplug on PE#4 and pdev#0/1, which
are not valid any more. Eventually, we run into kernel crash.

The patch fixes above issue from two aspects. For unplug, we simply
skip those permanently removed PE, whose state is (EEH_PE_STATE_ISOLATED
&& !EEH_PE_STATE_RECOVERING) and its frozen count should be greater
than EEH_MAX_ALLOWED_FREEZES. For plug, we marked all permanently
removed EEH devices with EEH_DEV_REMOVED and return 0xFF's on read
its PCI config so that PCI core will omit them.

Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

PCI: Convert pcibios_resource_to_bus() to take a pci_bus, not a pci_dev

These interfaces:

pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)

took a pci_dev, but they really depend only on the pci_bus. And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:

pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)

In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.

[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

powerpc: Fix little endian issue in OF PCI scan

This issue was causing the QEMU emulated USB device to fail dring
PCI probe.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

powerpc: Make OF PCI device tree accesses endian safe

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

powerpc/pci: Partial tree hotplug support

When EEH error happens to one specific PE, the device drivers
of its attached EEH devices (PCI devices) are checked to see
the further action: reset with complete hotplug, or reset without
hotplug. However, that's not enough for those PCI devices whose
drivers can't support EEH, or those PCI devices without driver.
So we need do so-called "partial hotplug" on basis of PCI devices.
In the situation, part of PCI devices of the specific PE are
unplugged and plugged again after PE reset.

The patch changes pcibios_add_pci_devices() so that it can support
full hotplug and so-called "partial" hotplug based on device-tree
or real hardware. It's notable that pci_of_scan.c has been changed
for a bit in order to support the "partial" hotplug based on dev-tree.

Most of the generic code already supports that, we just need to
plumb it properly on our side.

Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

PCI: Convert alloc_pci_dev(void) to pci_alloc_dev(bus)

Use the new pci_alloc_dev(bus) to replace the existing using of
alloc_pci_dev(void).

[bhelgaas: drop pci_bus ref later in pci_release_dev()]
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>

powerpc/PCI: Use PCI_UNKNOWN for unknown power state

Previously we initialized dev->current_state to 4 (PCI_D3cold), but I think
we wanted PCI_UNKNOWN (5) here based on the comment and the fact that the
generic version of this code, pci_setup_device(), uses PCI_UNKNOWN.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

POWERPC: drivers: remove __dev* attributes.

CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc: Fix kernel-doc warning

Warning(arch/powerpc/kernel/pci_of_scan.c:210): Excess function parameter 'node' description in 'of_scan_pci_bridge'
Warning(arch/powerpc/kernel/vio.c:636): No description found for parameter 'desired'
Warning(arch/powerpc/kernel/vio.c:636): Excess function parameter 'new_desired' description in 'vio_cmo_set_dev_desired'
Warning(arch/powerpc/kernel/vio.c:1270): No description found for parameter 'viodrv'
Warning(arch/powerpc/kernel/vio.c:1270): Excess function parameter 'drv' description in '__vio_register_driver'
Warning(arch/powerpc/kernel/vio.c:1289): No description found for parameter 'viodrv'
Warning(arch/powerpc/kernel/vio.c:1289): Excess function parameter 'driver' description in 'vio_unregister_driver'

Signed-off-by: Wanpeng Li <liwp@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

powerpc/PCI: register busn_res for root buses

Add the host bridge bus number aperture to the resource list.
Like the MMIO and I/O port apertures, this is used when assigning
resources to hot-added devices or in the case of conflicts.

[bhelgaas: changelog]
CC: Paul Mackerras <paulus@samba.org>
CC: linuxppc-dev@lists.ozlabs.org
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

PCI: replace struct pci_bus secondary/subordinate with busn_res

Replace the struct pci_bus secondary/subordinate members with the
struct resource busn_res. Later we'll build a resource tree of these
bus numbers.

[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

powerpc/PCI: convert devtree bus addresses to resource

Normal PCI enumeration via PCI config space uses __pci_read_base(), where
the PCI core applies any bus-to-resource offset. But powerpc doesn't use
that path when enumerating via the device tree.

In 6c5705fec63d, I converted powerpc to use the PCI core bus-to-resource
conversion, but I missed these powerpc-specific paths. Some powerpc
platforms fail to boot ("Cannot allocate resource region," "device not
available," etc.) between that commit and this one.

This adds the corresponding bus-to-resource conversion in the paths that
read BAR values from the OF device tree.

CC: Anton Blanchard <anton@samba.org>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

powerpc: add export.h to files making use of EXPORT_SYMBOL

With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

pci/of: Match PCI devices to OF nodes dynamically

powerpc has two different ways of matching PCI devices to their
corresponding OF node (if any) for historical reasons. The ppc64 one
does a scan looking for matching bus/dev/fn, while the ppc32 one does a
scan looking only for matching dev/fn on each level in order to be
agnostic to busses being renumbered (which Linux does on some
platforms).

This removes both and instead moves the matching code to the PCI core
itself. It's the most logical place to do it: when a pci_dev is created,
we know the parent and thus can do a single level scan for the matching
device_node (if any).

The benefit is that all archs now get the matching for free. There's one
hook the arch might want to provide to match a PHB bus to its device
node. A default weak implementation is provided that looks for the
parent device device node, but it's not entirely reliable on powerpc for
various reasons so powerpc provides its own.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>

powerpc/pci: Make both ppc32 and ppc64 use sysdata for pci_controller

Currently, ppc32 uses sysdata for the pci_controller pointer, and
ppc64 uses it to hold the device_node pointer. This patch moves the
of_node pointer into (struct pci_bus*)->dev.of_node and
(struct pci_dev*)->dev.of_node so that sysdata can be converted to always
use the pci_controller pointer instead. It also fixes up the
allocating of pci devices so that the of_node pointer gets assigned
consistently and increments the ref count.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

powerpc/pci: Fix checking for child bridges in PCI code.

pci_device_to_OF_node() can return null, and list_for_each_entry will
never enter the loop when dev is NULL, so it looks like this test is
a typo.

Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

powerpc/pci: Drop unnecessary null test

list_for_each_entry binds its first argument to a non-null value, and thus
any null test on the value of that argument is superfluous.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
iterator I;
expression x,E,E1,E2;
statement S,S1,S2;
@@

I(x,...) { <...
- if (x != NULL || ...)
S
...> }
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

powerpc/pci: Check devices status property when scanning OF tree

We ran into an issue where it looks like we're not properly ignoring a
pci device with a non-good status property when we walk the device tree
and instanciate the Linux side PCI devices.

However, the EEH init code does look for the property and disables EEH
on these devices. This leaves us in an inconsistent where we are poking
at a supposedly bad piece of hardware and RTAS will block our config
cycles because EEH isn't enabled anyway.

Signed-of-by: Sonny Rao <sonnyrao@linux.vnet.ibm.com>

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

powerpc: Remove trailing space in messages

Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

powerpc/pci: Add missing call to header fixup

Add missing call to pci_fixup_device(pci_fixup_early, ...) when
building the pci_dev from scratch off the Open Firmware device-tree

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

powerpc/pci: Add missing hookup to pci_slot

Add missing hookup to existing pci_slot when building the pci_dev from
scratch off the Open Firmware device-tree

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

powerpc/pci: Add calls to set_pcie_port_type() and set_pcie_hotplug_bridge()

We are missing these when building the pci_dev from scratch off
the Open Firmware device-tree

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>

powerpc/pci: move pci_64.c device tree scanning code into pci-common.c

The PCI device tree scanning code in pci_64.c is some useful functionality.
It allows PCI devices to be described in the device tree instead of being
probed for, which in turn allows pci devices to use all of the device tree
facilities to describe complex PCI bus architectures like GPIO and IRQ
routing (perhaps not a common situation for desktop or server systems,
but useful for embedded systems with on-board PCI devices).

This patch moves the device tree scanning into pci-common.c so it is
available for 32-bit powerpc machines too.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>