MIPS: Loongson64: Handle more memory types passed from firmware

There are many types of revsered memory passed from firmware
that should be reserved in memblock, and UMA memory passed
from firmware that should be added to system memory for system
to use.

Also for memblock there is no need to align those space into page,
which actually cause problems.

Handle them properly to prevent memory corruption on some systems.

Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: Loongson64: Enable DMA noncoherent support

There are some Loongson64 systems come with broken coherent DMA
support, firmware will set a bit in boot_param and pass nocoherentio
in cmdline.

However nonconherent support was missed out when spin off Loongson-2EF
form Loongson64, and that boot_param change never made itself into
upstream.

Support DMA noncoherent properly to get those systems working.

Cc: stable@vger.kernel.org
Fixes: 71e2f4dd5a65 ("MIPS: Fork loongson2ef from loongson64")
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: Loongson64: Move loongson_system_configuration to loongson.h

The purpose of separating loongson_system_configuration from boot_param.h
is to keep the other structure consistent with the firmware.

Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Qing Zhang <zhangqing@loongson.cn>
Acked-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: Loongson64: Remove unused sysconf members

We don't need them anymore, They are uniform on all Loongson64 systems
and have been fixed in DeviceTree.loongson3_platform_init is replaced
with DTS + driver.

Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Qing Zhang <zhangqing@loongson.cn>
Acked-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: Loongson64: Add /sys/firmware/lefi/boardinfo

Add /sys/firmware/lefi/boardinfo to get mainboard and BIOS info easily
on the Loongson platform, this is useful to point out the current used
mainboard type and BIOS version when there exists problems related with
hardware or firmware.

The related structures are already defined in the interface specification
about firmware and kernel which are common requirement and specific for
Loongson64, so only add a new boardinfo.c file in arch/mips/loongson64.

E.g. with this patch:

[loongson@linux ~]$ cat /sys/firmware/lefi/boardinfo
Board Info
Manufacturer : LEMOTE
Board Name : LEMOTE-LS3A4000-7A1000-1w-V01-pc
Family : LOONGSON3

BIOS Info
Vendor : Kunlun
Version : Kunlun-A1901-V4.1.3-20200414093938
ROM Size : 4 KB
Release Date : 2020-04-14

By the way, using dmidecode command can get the similar info if there
exists SMBIOS in firmware, but the fact is that there is no SMBIOS on
some machines, we can see nothing when execute dmidecode, like this:

[root@linux loongson]# dmidecode
# dmidecode 2.12
# No SMBIOS nor DMI entry point found, sorry.

Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: KVM: Add kvm guest support for Loongson-3

Loongson-3 KVM guest is based on virtio, it use liointc as its interrupt
controller and use GPEX as the pci controller.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: Loongson: Add DMA support for LS7A

In the current market, the most used bridge chip on the Loongson platform
are RS780E and LS7A, the RS780E bridge chip is already supported by the
mainline kernel.

If use the default implementation of __phys_to_dma() and __dma_to_phys()
in dma-direct.h when CONFIG_ARCH_HAS_PHYS_TO_DMA is not set, it works
well used with LS7A on the Loongson single-way and multi-way platform,
and also works well used with RS780E on the Loongson single-way platform,
but the DMA address will be wrong on the non-node0 used with RS780E on
the Loongson multi-way platform.

Just as the description in the code comment, the devices get node id from
40 bit of HyperTransport bus, so we extract 2 bit node id (bit 44~45) from
48 bit address space of Loongson CPU and embed it into HyperTransport bus
(bit 37-38), this operation can be done only at the software level used
with RS780E on the Loongson multi-way platform, because it has no hardware
function to translate address of node id, this is a hardware compatibility
problem.

Device
|
| DMA address
|
Host Bridge
|
| HT bus address (40 bit)
|
CPU
|
| physical address (48 bit)
|
RAM

The LS7A has dma_node_id_offset field in the DMA route config register,
the hardware can use the dma_node_id_offset to translate address of
node id automatically, so we can get correct address when just use the
dma_pfn_offset field in struct device.

For the above reasons, in order to maintain downward compatibility
to support the RS780E bridge chip, it is better to use the platform
dependent implementation of __phys_to_dma() and __dma_to_phys().

Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: Loongson64: Switch the order of RS780E and LS7A

Sort the members of enum in alphabetical order is better to avoid
duplicate mistakes (because the list may be grow very large), so
fix it by exchanging the order.

Signed-off-by: Liangliang Huang <huangll@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: Loongson: Get host bridge information

Read the address of host bridge configuration space to get the vendor ID
and device ID of host bridge, and then we can distinguish various types
of host bridge such as LS7A or RS780E.

Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: Loongson64: Drop legacy IRQ code

We've made generic irqchip drivers for Loongson-3 platform, it's time
to say goodbye to these legacy code.

Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Co-developed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: Loongson fix name confict - MEM_RESERVED

MEM_RESERVED is used as a value of enum mem_type in include/linux/
edac.h. This will make failure to build for Loongson in some case:
for example with CONFIG_RAS enabled.

So here rename MEM_RESERVED to SYSTEM_RAM_RESERVED in Loongson code.

Signed-off-by: YunQiang Su <yunqiang.su@imgtec.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17724/
Signed-off-by: James Hogan <jhogan@kernel.org>

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Loogson: Make enum loongson_cpu_type more clear

Sort enum loongson_cpu_type in a more reasonable manner, this makes the
CPU names more clear and extensible. Those already defined enum values
are renamed to Legacy_* for compatibility.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@cavium.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16591/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson: Naming style cleanup and rework

Currently, code of Loongson-2/3 is under loongson directory and code of
Loongson-1 is under loongson1 directory. Besides, there are Kconfig
options such as MACH_LOONGSON and MACH_LOONGSON1. This naming style is
very ugly and confusing. Since Loongson-2/3 are both 64-bit general-
purpose CPU while Loongson-1 is 32-bit SoC, we rename both file names
and Kconfig symbols from loongson/loongson1 to loongson64/loongson32.

[ralf@linux-mips.org: Resolve a number of simple conflicts.]

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9790/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>