MIPS: BCM47XX: Add support for Huawei B593u-12

It's a BCM5358 based home router. One of very few bcm47xx devices with
cellular modems (here: LTE).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: BCM47XX: Add support for Linksys E2500 V3

It's a BCM5358 based home WiFi router. 16 MiB flash, 64 MiB RAM, BCM5325
switch, on-SoC 802.11n radio.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: BCM47XX: Add support for Netgear WNR3500L v2

Add support for the Netgear WNR3500L v2 router based on the BCM47186
chipset and supporting 802.11n Wi-Fi.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: BCM47XX: Add support for Netgear WN2500RP v1 & v2

Add support for the Netgear WN2500 RP v1 and v2 Wi-Fi range extenders
based on the BCM5357 chipset and supporting 802.11n and 802.11ac.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: BCM47XX: Add support for Netgear R6300 v1

Add support for the Netgear R6300 v1 Wi-Fi router using a Broadcom
BCM4706 chipset and supporting 802.11n and 802.11ac.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: BCM47XX: Add board entry for Linksys WRT320N v1

This router is based on a Broadcom BCM4717A1 chipset and supports
802.11n Wi-Fi. Add a board entry for that router and register LEDs and
buttons accordingly.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: BCM47XX: Add support for Netgear R6200 V1

The Netgear R6200 v1 uses a BCM4718A1 SOC and a BCM4352/BCM4360 for 5GHz
wireless. This patch adds support for detecting this model board and
registers the 3 buttons.

I have tested that the device can boot kernels 4.14 and 4.19 under
OpenWRT.

There is one issue that the LEDs on the device are controlled by a
74HC164 that uses bit-banging instead of SPI so it isn't accessible to
the kernel without adding a workaround. Without any workaround the
device on boot will flash all LEDs once then the power LED will remain
amber as all other LEDs stay off.

Signed-off-by: Edward Matijevic <motolav@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
[paul.burton@mips.com:
- Sort bcm47xx_board_list_board_id alphabetically by board type.
- Fix whitespace.
- Wrap commit message & drop OpenWRT-based justification for
bcm47xx_board_list_board_id being mis-sorted.]
Signed-off-by: Paul Burton <paul.burton@mips.com>

MIPS: BCM47XX: Add support for Netgear WNR1000 V3

This adds support for detecting this model board and registers some LEDs
and buttons.

There are two uncommon things regarding this device:
1) It can use two different "board_id" ID values.
Unit I have uses "U12H139T00_NETGEAR" value. This magic is also used
in firmware file header. There are two reports (one from an OpenWrt
user) of a different "U12H139T50_NETGEAR" magic though.
2) Power LEDs share GPIOs with buttons.
Amber one seems to share GPIO 2 with WPS button and green one seems
to share GPIO 3 with reset button. It remains unknown how to support
them and handle buttons at the same time. For that reason they aren't
added to the list of supported LEDs.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19004/
Signed-off-by: James Hogan <jhogan@kernel.org>

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: BCM47XX: Add Luxul devices to the database

So far only Luxul XWR-1750 router was supported. This adds a set of
other Luxul devices based on BCM47XX. It's a standard support for LEDs
and buttons.

Signed-off-by: Dan Haab <dhaab@luxul.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15106/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47XX: Support Luxul XWR-1750 board

Signed-off-by: Dan Haab <dhaab@luxul.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Dan Haab <dhaab@luxul.com>
Patchwork: https://patchwork.linux-mips.org/patch/9831/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47xx: Devices database update for 4.1 (or 4.2?)

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/9656/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47xx: Distinguish WRT54G series devices by boardtype

Catalin reported that GPIOs used by bcm47xx don't match layout of his
WRT54GS V1.0 board. It seems we need to distinguish these 54G* devices.

Reported-by: Catalin Patulea <cat@vv.carleton.ca>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/7112/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47XX: add Microsoft MN-700 and Asus WL500G

This patch adds detection for the Microsoft MN-700 and the Asus WL500G
router. This is based on some old code from OpenWrt.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7490/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47XX: Add Belkin F7Dxxxx board detection

Add a few Belkin F7Dxxxx entries, with F7D4401 sourced from online
documentation and the "F7D7302" being observed. F7D3301, F7D3302, and
F7D4302 are reasonable guesses which are unlikely to cause
mis-detection.

Signed-off-by: Cody P Schafer <devel@codyps.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Cc: Cody P Schafer <devel@codyps.com>
Patchwork: https://patchwork.linux-mips.org/patch/6594/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47XX: Add detection and GPIO config for Siemens SE505v2

This adds board detection for the Siemens SE505v2 and the led gpio
configuration. This board does not have any buttons.
This is based on OpenWrt broadcom-diag and Manuel Munz's nvram dump.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6593/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47XX: Detect some more Linksys devices

The Linksys WRT54G/GS/GL family uses the same boardtype numbers, and
the same gpio configuration. The boardtype numbers are changing with
the hardware versions, but these hardware numbers are different or each
model.
Detect them all as one device, this also worked in OpenWrt.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6591/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM47XX: add board detection for Linksys WRT54GS V1

This adds board detection for Linksys WRT54GS V1.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6317/

MIPS: BCM47XX: Add board detection

Detect on which board this code is running based on some nvram
settings. This is needed to start board specific workarounds and
configure the leds and buttons which are on different gpios on every board.

This patches add some boards we have seen, but there are many more.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5840
Patchwork: https://patchwork.linux-mips.org/patch/5855/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>