MIPS: DTS: CI20: Raise VDDCORE voltage to 1.125 volts

Commit 08384e80a70f ("MIPS: DTS: CI20: Fix ACT8600 regulator node
names") caused the VDDCORE power supply (regulated by the ACT8600's
DCDC1 output) to drop from a voltage of 1.2V configured by the
bootloader, to the 1.1V set in the Device Tree.

According to the documentation, the VDDCORE supply should be between
0.99V and 1.21V; both values are therefore within the supported range.

However, VDDCORE being 1.1V results in the CI20 being very unstable,
with corrupted memory, failures to boot, or reboots at random. The
reason might be succint drops of the voltage below the minimum required.

Raising the minimum voltage to 1.125 volts seems to be enough to address
this issue, while still keeping a relatively low core voltage which
helps for power consumption and thermals.

Fixes: 08384e80a70f ("MIPS: DTS: CI20: Fix ACT8600 regulator node names")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: Enable support for WiFi / Bluetooth

Wire the WiFi/Bluetooth chip properly in the Device Tree.

- Provide it with the correct regulators and clocks;
- Change the MMC I/O bus to 1.8V which seems to be enough;
- Change the MMC I/O bus frequency to 25 MHz as 50 MHz causes errors;
- Fix the Bluetooth powerdown GPIO being inverted and add reset GPIO;
- Convert host-wakeup-gpios to IRQ.

With these changes, the WiFi works properly with the latest firmware
provided by linux-firmware. The Bluetooth does not work very well here,
as I cannot get my wireless keyboard to pair; but it does detect it, and
it does see the key presses when I type the pairing code.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: Parent MSCMUX clock to MPLL

This makes it possible to clock the SD cards much higher, as the MPLL is
running at 1.2 GHz by default. The previous parent was the EXT clock,
which caused the SD cards to be clocked at 24 MHz maximum.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: Misc. cleanups

- Use the standard "ecc-engine" property instead of the custom
"ingenic,bch-controller" to get a handle to the BCH controller.

- Respect cell sizes in the Ethernet controller node.

- Use proper macro for interrupt type instead of hardcoding magic
values.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: Do not force-enable CIM and WiFi regulators

These regulators should be enabled by their respective drivers.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: Add parent supplies to ACT8600 regulators

Provide parent regulators to the ACT8600 regulators that need one.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: Fix ACT8600 regulator node names

The Device Tree was using invalid node names for the ACT8600 regulators.
To be fair, it is not the original committer's fault, as the
documentation did gives invalid names as well.

In theory, the fix should have been to modify the driver to accept the
alternative names. However, even though the act8865 driver spits
warnings, the kernel seemed to work fine with what is currently
supported upstream. For that reason, I think it is okay to just update
the DTS.

I removed the "regulator-name" too, since they really didn't bring any
information. The node names are enough.

Fixes: 73f2b940474d ("MIPS: CI20: DTS: Add I2C nodes")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: Fix regulators

The regulators don't have any "reg" property, and therefore shouldn't
use an unit address in their node names. They also don't need to specify
the GPIO_ACTIVE_LOW flag, which will be ignored anyway, as they are
active-high.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

mips: dts: align LED node names with dtschema

The node names should be generic and DT schema expects certain pattern:

mt7621-gnubee-gb-pc1.dtb: gpio-leds: 'power', 'system' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: fix otg power gpio

According to schematics it is PF15 and not PF14 (MIC_SW_EN).
Seems as if it was hidden and not noticed during testing since
there is no sound DT node.

Fixes: 158c774d3c64 ("MIPS: Ingenic: Add missing nodes for Ingenic SoCs and boards.")
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: fix reset line polarity of the ethernet controller

The reset line is called PWRST#, annotated as "active low" in the
binding documentation, and is driven low and then high by the driver to
reset the chip. However in device tree for CI20 board it was incorrectly
marked as "active high". Fix it.

Because (as far as I know) the ci20.dts is always built in the kernel I
elected not to also add a quirk to gpiolib to force the polarity there.

Fixes: db49ca38579d ("net: davicom: dm9000: switch to using gpiod API")
Reported-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: dts: align gpio-key node names with dtschema

The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: fix how ddc power is enabled

Originally we proposed a new hdmi-5v-supply regulator reference
for CI20 device tree but that was superseded by a better idea to use
the already defined "ddc-en-gpios" property of the "hdmi-connector".

Since "MIPS: DTS: CI20: Add DT nodes for HDMI setup" has already
been applied to v5.17-rc1, we add this on top.

Fixes: ae1b8d2c2de9 ("MIPS: DTS: CI20: Add DT nodes for HDMI setup")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: Add DT nodes for HDMI setup

We need to hook up
* HDMI connector
* HDMI power regulator
* JZ4780_CLK_HDMI @ 27 MHz
* DDC pinmux
* HDMI and LCDC endpoint connections

Signed-off-by: Paul Boddie <paul@boddie.org.uk>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: JZ4780: CI20: DTS: add SPI controller config

1. Add nodes for the two SPI controllers found in MIPS Creator CI20.
2. Reparent SPI clock source to effectively use MPLL and set its clock
rate to 54MHz.

NOTE: To use the SPI controllers, `pinctrl-0` property must be set in
order to configure the used pins. As SPI functionality is multiplexed on
multiple pin groups, this choice is left to the user.

An example configuration:
```
&spi0 {
pinctrl-0 = <&pins_spi0>;
}

pins_spi0: spi0 {
function = "ssi0";
groups = "ssi0-dt-e", "ssi0-dr-e", "ssi0-clk-e",
"ssi0-ce0-e", "ssi0-ce1-e";
bias-disable;
};
```
Consult the CI20 pinout description for more details.

Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Link: https://lore.kernel.org/r/20210830230139.21476-4-contact@artur-rojek.eu
Signed-off-by: Mark Brown <broonie@kernel.org>

MIPS: CI20: Add second percpu timer for SMP.

1.Add a new TCU channel as the percpu timer of core1, this is to
prepare for the subsequent SMP support. The newly added channel
will not adversely affect the current single-core state.
2.Adjust the position of TCU node to make it consistent with the
order in jz4780.dtsi file.

Tested-by: Nikolaus Schaller <hns@goldelico.com> # on CI20
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: CI20: Reduce clocksource to 750 kHz.

The original clock (3 MHz) is too fast for the clocksource,
there will be a chance that the system may get stuck.

Reported-by: Nikolaus Schaller <hns@goldelico.com>
Tested-by: Nikolaus Schaller <hns@goldelico.com> # on CI20
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: Ingenic: Add missing nodes for Ingenic SoCs and boards.

1.Add OTG/OTG PHY/RNG nodes for JZ4780, CGU/OTG nodes for CI20.
2.Add OTG/OTG PHY/RNG/OST nodes for X1000, SSI/CGU/OST/OTG/SC16IS752
nodes for CU1000-Neo.
3.Add OTG/OTG PHY/DTRNG/OST nodes for X1830, SSI/CGU/OST/OTG/SC16IS752
nodes for CU1830-Neo.

Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Tested by: H. Nikolaus Schaller <hns@goldelico.com> # CI20/jz4780
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: make DM9000 Ethernet controller use NVMEM to find the default MAC address

There is a unique MAC address programmed into the eFuses
of the JZ4780 chip in the CI20 factory. By using this
for initializing the DM9000 Ethernet controller, every
CI20 board has an individual - but stable - MAC address
and DHCP can assign stable IP addresses.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: multiple DTS improvements

a) add DT node for SW1 as Enter button

The SW1 button can be used as a simple one-button keyboard
and is connected to PD17.

Note: SW1 has a second meaning to change the boot sequence
when pressed while powering on.

b) give eth0_power a defined voltage.

This is a 3.3V power switch (DVNET3.3V).

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: add DT node for IR sensor

The infrared sensor on the CI20 board is connected to a GPIO and can
be operated by using the gpio-ir-recv driver. Add a DT node for the
sensor to allow that driver to be used.

Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: fix interrupt for pcf8563 RTC

Interrupts should not be specified by interrupt line but by
gpio parent and reference.

Fixes: 73f2b940474d ("MIPS: CI20: DTS: Add I2C nodes")
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: DTS: CI20: fix PMU definitions for ACT8600

There is a ACT8600 on the CI20 board and the bindings of the
ACT8865 driver have changed without updating the CI20 device
tree. Therefore the PMU can not be probed successfully and
is running in power-on reset state.

Fix DT to match the latest act8865-regulator bindings.

Fixes: 73f2b940474d ("MIPS: CI20: DTS: Add I2C nodes")
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

MIPS: CI20: DTS: Add Leds

Adding leds and related triggers.

Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org

MIPS: CI20: DTS: Add IW8103 Wifi + bluetooth

Add IW8103 Wifi + bluetooth module to device tree and related power domain.

Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org

MIPS: CI20: DTS: Add I2C nodes

Adding missing I2C nodes and some peripheral:
- PMU
- RTC

Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org

MIPS: CI20: Reduce system timer and clocksource to 3 MHz

The default clock (48 MHz) is too fast for the system timer.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me

DTS: CI20: Fix bugs in ci20's device tree.

According to the Schematic, the hardware of ci20 leads to uart3,
but not to uart2. Uart2 is miswritten in the original code.

Signed-off-by: Zhou Yanjie <zhouyanjie@cduestc.edu.cn>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips <linux-mips@vger.kernel.org>
Cc: linux-kernel <linux-kernel@vger.kernel.org>
Cc: devicetree@vger.kernel.org
Cc: robh+dt@kernel.org
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: mark.rutland@arm.com
Cc: malat@debian.org
Cc: ezequiel@collabora.co.uk
Cc: ulf.hansson@linaro.org
Cc: syq <syq@debian.org>
Cc: jiaxun.yang <jiaxun.yang@flygoat.com>

MIPS: dts: ci20: Enable MMC in the devicetree

Now that we have support for JZ480 SoCs in the MMC driver,
let's enable it on the devicetree.

Acked-by: James Hogan <jhogan@kernel.org>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

MIPS: dts: Fix a typo in the node unit name

The unit name was 8c00000 but since the reg property is declared as:

reg = <0x0 0x4c00000 0x1 0xfb400000>;

the unit name should have been instead 4c00000.

Tested on MIPS Creator CI20 (v1):

$ cat /sys/firmware/devicetree/.../partitions/partition@4c00000/label;echo
system

Reported-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18529/
Signed-off-by: James Hogan <jhogan@kernel.org>

MIPS: dts: Remove leading 0x and 0s from bindings notation

Improve the DTS files by removing all the leading "0x" and zeros to fix
the following dtc warnings:

Warning (unit_address_format): Node /XXX unit name should not have leading "0x"

and

Warning (unit_address_format): Node /XXX unit name should not have leading 0s

Converted using the following command:

find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +

For simplicity, two sed expressions were used to solve each warnings
separately.

To make the regex expression more robust a few other issues were
resolved, namely setting unit-address to lower case, and adding a
whitespace before the the opening curly brace:

https://elinux.org/Device_Tree_Linux#Linux_conventions

This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading
0x from bindings notation")

Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18528/
Signed-off-by: James Hogan <jhogan@kernel.org>

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: dts: Ci20: Add ethernet and fixed-regulator nodes

Add devicetree nodes for the DM9000 and the ethernet power regulator.
Additionally, add a new pinctrl node for the ethernet chip's pins.

Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16752/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: JZ4780: CI20: Add pinctrl configuration for several drivers

We set the pin configuration for the jz4780-nand and jz4780-uart
drivers.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

MIPS: dts: jz4780/ci20: Add NEMC, BCH and NAND device tree nodes

Add device tree nodes for the NEMC and BCH to the JZ4780 device tree,
and make use of them in the Ci20 device tree to add a node for the
board's NAND.

Note that since the pinctrl driver is not yet upstream, this includes
neither pin configuration nor busy/write-protect GPIO pins for the
NAND. Use of the NAND relies on the boot loader to have left the pins
configured in a usable state, which should be the case when booted
from the NAND.

[ralf@linux-mips.org: fold in Geert Uytterhoeven's patch and acks from
Harvey's latest version.]

Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: linux-mtd@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-mtd@lists.infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/11695/
Patchwork: https://patchwork.linux-mips.org/patch/11914/
Patchwork: https://patchwork.linux-mips.org/patch/11985/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ingenic: Initial MIPS Creator CI20 support

Add an initial device tree for the Ingenic JZ4780 based MIPS Creator
CI20 board.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10162/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>