efi: arm64: enter with MMU and caches enabled

Instead of cleaning the entire loaded kernel image to the PoC and
disabling the MMU and caches before branching to the kernel's bare metal
entry point, we can leave the MMU and caches enabled, and rely on EFI's
cacheable 1:1 mapping of all of system RAM (which is mandated by the
spec) to populate the initial page tables.

This removes the need for managing coherency in software, which is
tedious and error prone.

Note that we still need to clean the executable region of the image to
the PoU if this is required for I/D coherency, but only if we actually
decided to move the image in memory, as otherwise, this will have been
taken care of by the loader.

This change affects both the builtin EFI stub as well as the zboot
decompressor, which now carries the entire EFI stub along with the
decompression code and the compressed image.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20230111102236.1430401-7-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: mm: Remove assembly DMA cache maintenance wrappers

Remove the __dma_{flush,map,unmap}_area assembly wrappers and call the
appropriate cache maintenance functions directly from the DMA mapping
callbacks.

Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220610151228.4562-3-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>

arm64: mm: Don't invalidate FROM_DEVICE buffers at start of DMA transfer

Invalidating the buffer memory in arch_sync_dma_for_device() for
FROM_DEVICE transfers

When using the streaming DMA API to map a buffer prior to inbound
non-coherent DMA (i.e. DMA_FROM_DEVICE), we invalidate any dirty CPU
cachelines so that they will not be written back during the transfer and
corrupt the buffer contents written by the DMA. This, however, poses two
potential problems:

(1) If the DMA transfer does not write to every byte in the buffer,
then the unwritten bytes will contain stale data once the transfer
has completed.

(2) If the buffer has a virtual alias in userspace, then stale data
may be visible via this alias during the period between performing
the cache invalidation and the DMA writes landing in memory.

Address both of these issues by cleaning (aka writing-back) the dirty
lines in arch_sync_dma_for_device(DMA_FROM_DEVICE) instead of discarding
them using invalidation.

Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220606152150.GA31568@willie-the-truck
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220610151228.4562-2-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: clean up symbol aliasing

Now that we have SYM_FUNC_ALIAS() and SYM_FUNC_ALIAS_WEAK(), use those
to simplify and more consistently define function aliases across
arch/arm64.

Aliases are now defined in terms of a canonical function name. For
position-independent functions I've made the __pi_<func> name the
canonical name, and defined other alises in terms of this.

The SYM_FUNC_{START,END}_PI(func) macros obscure the __pi_<func> name,
and make this hard to seatch for. The SYM_FUNC_START_WEAK_PI() macro
also obscures the fact that the __pi_<func> fymbol is global and the
<func> symbol is weak. For clarity, I have removed these macros and used
SYM_FUNC_{START,END}() directly with the __pi_<func> name.

For example:

SYM_FUNC_START_WEAK_PI(func)
... asm insns ...
SYM_FUNC_END_PI(func)
EXPORT_SYMBOL(func)

... becomes:

SYM_FUNC_START(__pi_func)
... asm insns ...
SYM_FUNC_END(__pi_func)

SYM_FUNC_ALIAS_WEAK(func, __pi_func)
EXPORT_SYMBOL(func)

For clarity, where there are multiple annotations such as
EXPORT_SYMBOL(), I've tried to keep annotations grouped by symbol. For
example, where a function has a name and an alias which are both
exported, this is organised as:

SYM_FUNC_START(func)
... asm insns ...
SYM_FUNC_END(func)
EXPORT_SYMBOL(func)

SYM_FUNC_ALIAS(alias, func)
EXPORT_SYMBOL(alias)

For consistency with the other string functions, I've defined strrchr as
a position-independent function, as it can safely be used as such even
though we have no users today.

As we no longer use SYM_FUNC_{START,END}_ALIAS(), our local copies are
removed. The common versions will be removed by a subsequent patch.

There should be no functional change as a result of this patch.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Joey Gouly <joey.gouly@arm.com>
Cc: Will Deacon <will@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220216162229.1076788-3-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>

arm64: remove __dma_*_area() aliases

The __dma_inv_area() and __dma_clean_area() aliases make cache.S harder
to navigate, but don't gain us anything in practice.

For clarity, let's remove them along with their redundant comments. The
only users are __dma_map_area() and __dma_unmap_area(), which need to be
position independent, and can call __pi_dcache_inval_poc() and
__pi_dcache_clean_poc() directly.

There should be no functional change as a result of this patch.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Fuad Tabba <tabba@google.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Will Deacon <will@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20211206124715.4101571-4-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: Rename arm64-internal cache maintenance functions

Although naming across the codebase isn't that consistent, it
tends to follow certain patterns. Moreover, the term "flush"
isn't defined in the Arm Architecture reference manual, and might
be interpreted to mean clean, invalidate, or both for a cache.

Rename arm64-internal functions to make the naming internally
consistent, as well as making it consistent with the Arm ARM, by
specifying whether it applies to the instruction, data, or both
caches, whether the operation is a clean, invalidate, or both.
Also specify which point the operation applies to, i.e., to the
point of unification (PoU), coherency (PoC), or persistence
(PoP).

This commit applies the following sed transformation to all files
under arch/arm64:

"s/\b__flush_cache_range\b/caches_clean_inval_pou_macro/g;"\
"s/\b__flush_icache_range\b/caches_clean_inval_pou/g;"\
"s/\binvalidate_icache_range\b/icache_inval_pou/g;"\
"s/\b__flush_dcache_area\b/dcache_clean_inval_poc/g;"\
"s/\b__inval_dcache_area\b/dcache_inval_poc/g;"\
"s/__clean_dcache_area_poc\b/dcache_clean_poc/g;"\
"s/\b__clean_dcache_area_pop\b/dcache_clean_pop/g;"\
"s/\b__clean_dcache_area_pou\b/dcache_clean_pou/g;"\
"s/\b__flush_cache_user_range\b/caches_clean_inval_user_pou/g;"\
"s/\b__flush_icache_all\b/icache_inval_all_pou/g;"

Note that __clean_dcache_area_poc is deliberately missing a word
boundary check at the beginning in order to match the efistub
symbols in image-vars.h.

Also note that, despite its name, __flush_icache_range operates
on both instruction and data caches. The name change here
reflects that.

No functional change intended.

Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-19-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>

arm64: __clean_dcache_area_pou to take end parameter instead of size

To be consistent with other functions with similar names and
functionality in cacheflush.h, cache.S, and cachetlb.rst, change
to specify the range in terms of start and end, as opposed to
start and size.

No functional change intended.

Reported-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-16-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>

arm64: __clean_dcache_area_pop to take end parameter instead of size

To be consistent with other functions with similar names and
functionality in cacheflush.h, cache.S, and cachetlb.rst, change
to specify the range in terms of start and end, as opposed to
start and size.

No functional change intended.

Reported-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-15-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>

arm64: __clean_dcache_area_poc to take end parameter instead of size

To be consistent with other functions with similar names and
functionality in cacheflush.h, cache.S, and cachetlb.rst, change
to specify the range in terms of start and end, as opposed to
start and size.

Because the code is shared with __dma_clean_area, it changes the
parameters for that as well. However, __dma_clean_area is local to
cache.S, so no other users are affected.

No functional change intended.

Reported-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-14-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>

arm64: __flush_dcache_area to take end parameter instead of size

To be consistent with other functions with similar names and
functionality in cacheflush.h, cache.S, and cachetlb.rst, change
to specify the range in terms of start and end, as opposed to
start and size.

No functional change intended.

Reported-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-13-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>

arm64: dcache_by_line_op to take end parameter instead of size

To be consistent with other functions with similar names and
functionality in cacheflush.h, cache.S, and cachetlb.rst, change
to specify the range in terms of start and end, as opposed to
start and size.

No functional change intended.

Reported-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-12-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>

arm64: __inval_dcache_area to take end parameter instead of size

To be consistent with other functions with similar names and
functionality in cacheflush.h, cache.S, and cachetlb.rst, change
to specify the range in terms of start and end, as opposed to
start and size.

Because the code is shared with __dma_inv_area, it changes the
parameters for that as well. However, __dma_inv_area is local to
cache.S, so no other users are affected.

No functional change intended.

Reported-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-11-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>

arm64: Fix comments to refer to correct function __flush_icache_range

Many comments refer to the function flush_icache_range, where the
intent is in fact __flush_icache_range. Fix these comments to
refer to the intended function.

That's probably due to commit 3b8c9f1cdfc506e9 ("arm64: IPI each
CPU after invalidating the I-cache for kernel mappings"), which
renamed flush_icache_range() to __flush_icache_range() and added
a wrapper.

No functional change intended.

Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-10-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>

arm64: Do not enable uaccess for invalidate_icache_range

invalidate_icache_range() works on kernel addresses, and doesn't
need uaccess. Remove the code that toggles uaccess_ttbr0_enable,
as well as the code that emits an entry into the exception table
(via the macro invalidate_icache_by_line).

Changes return type of invalidate_icache_range() from int (which
used to indicate a fault) to void, since it doesn't need uaccess
and won't fault. Note that return value was never checked by any
of the callers.

No functional change intended.
Possible performance impact due to the reduced number of
instructions.

Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/linux-arch/20200511110014.lb9PEahJ4hVOYrbwIb_qUHXyNy9KQzNFdb_I3YlzY6A@z/
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-6-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>

arm64: Do not enable uaccess for flush_icache_range

__flush_icache_range works on kernel addresses, and doesn't need
uaccess. The existing code is a side-effect of its current
implementation with __flush_cache_user_range fallthrough.

Instead of fallthrough to share the code, use a common macro for
the two where the caller specifies an optional fixup label if
user access is needed. If provided, this label would be used to
generate an extable entry.

Simplify the code to use dcache_by_line_op, instead of
replicating much of its functionality.

No functional change intended.
Possible performance impact due to the reduced number of
instructions.

Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will@kernel.org>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/linux-arch/20200511110014.lb9PEahJ4hVOYrbwIb_qUHXyNy9KQzNFdb_I3YlzY6A@z/
Link: https://lore.kernel.org/linux-arm-kernel/20210521121846.GB1040@C02TD0UTHF1T.local/
Signed-off-by: Fuad Tabba <tabba@google.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-5-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>

arm64: mm: Use modern annotations for assembly functions

In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These replace ENTRY and
ENDPROC and also add a new annotation for static functions which previously
had no ENTRY equivalent. Update the annotations in the mm code to the
new macros. Even the functions called from non-standard environments
like idmap have no special requirements on their environments so can be
treated like regular functions.

Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 234

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 503 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: Fix minor issues with the dcache_by_line_op macro

The dcache_by_line_op macro suffers from a couple of small problems:

First, the GAS directives that are currently being used rely on
assembler behavior that is not documented, and probably not guaranteed
to produce the correct behavior going forward. As a result, we end up
with some undefined symbols in cache.o:

$ nm arch/arm64/mm/cache.o
...
U civac
...
U cvac
U cvap
U cvau

This is due to the fact that the comparisons used to select the
operation type in the dcache_by_line_op macro are comparing symbols
not strings, and even though it seems that GAS is doing the right
thing here (undefined symbols by the same name are equal to each
other), it seems unwise to rely on this.

Second, when patching in a DC CVAP instruction on CPUs that support it,
the fallback path consists of a DC CVAU instruction which may be
affected by CPU errata that require ARM64_WORKAROUND_CLEAN_CACHE.

Solve these issues by unrolling the various maintenance routines and
using the conditional directives that are documented as operating on
strings. To avoid the complexity of nested alternatives, we move the
DC CVAP patching to __clean_dcache_area_pop, falling back to a branch
to __clean_dcache_area_poc if DCPOP is not supported by the CPU.

Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64: IPI each CPU after invalidating the I-cache for kernel mappings

When invalidating the instruction cache for a kernel mapping via
flush_icache_range(), it is also necessary to flush the pipeline for
other CPUs so that instructions fetched into the pipeline before the
I-cache invalidation are discarded. For example, if module 'foo' is
unloaded and then module 'bar' is loaded into the same area of memory,
a CPU could end up executing instructions from 'foo' when branching into
'bar' if these instructions were fetched into the pipeline before 'foo'
was unloaded.

Whilst this is highly unlikely to occur in practice, particularly as
any exception acts as a context-synchronizing operation, following the
letter of the architecture requires us to execute an ISB on each CPU
in order for the new instruction stream to be visible.

Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64: Add support for new control bits CTR_EL0.DIC and CTR_EL0.IDC

The DCache clean & ICache invalidation requirements for instructions
to be data coherence are discoverable through new fields in CTR_EL0.
The following two control bits DIC and IDC were defined for this
purpose. No need to perform point of unification cache maintenance
operations from software on systems where CPU caches are transparent.

This patch optimize the three functions __flush_cache_user_range(),
clean_dcache_area_pou() and invalidate_icache_range() if the hardware
reports CTR_EL0.IDC and/or CTR_EL0.IDC. Basically it skips the two
instructions 'DC CVAU' and 'IC IVAU', and the associated loop logic
in order to avoid the unnecessary overhead.

CTR_EL0.DIC: Instruction cache invalidation requirements for
instruction to data coherence. The meaning of this bit[29].
0: Instruction cache invalidation to the point of unification
is required for instruction to data coherence.
1: Instruction cache cleaning to the point of unification is
not required for instruction to data coherence.

CTR_EL0.IDC: Data cache clean requirements for instruction to data
coherence. The meaning of this bit[28].
0: Data cache clean to the point of unification is required for
instruction to data coherence, unless CLIDR_EL1.LoC == 0b000
or (CLIDR_EL1.LoUIS == 0b000 && CLIDR_EL1.LoUU == 0b000).
1: Data cache clean to the point of unification is not required
for instruction to data coherence.

Co-authored-by: Philip Elcan <pelcan@codeaurora.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64: mm: Add additional parameter to uaccess_ttbr0_disable

Add an extra temporary register parameter to uaccess_ttbr0_disable which
is about to be required for arm64 PAN support.

This patch doesn't introduce any functional change but ensures that the
kernel compiles once the KVM/ARM tree is merged with the arm64 tree by
ensuring a trivially mergable conflict with commit
6b88a32c7af68895134872cdec3b6bfdb532d94e
("arm64: kpti: Fix the interaction between ASID switching and software PAN").

Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

arm64: kpti: Fix the interaction between ASID switching and software PAN

With ARM64_SW_TTBR0_PAN enabled, the exception entry code checks the
active ASID to decide whether user access was enabled (non-zero ASID)
when the exception was taken. On return from exception, if user access
was previously disabled, it re-instates TTBR0_EL1 from the per-thread
saved value (updated in switch_mm() or efi_set_pgd()).

Commit 7655abb95386 ("arm64: mm: Move ASID from TTBR0 to TTBR1") makes a
TTBR0_EL1 + ASID switching non-atomic. Subsequently, commit 27a921e75711
("arm64: mm: Fix and re-enable ARM64_SW_TTBR0_PAN") changes the
__uaccess_ttbr0_disable() function and asm macro to first write the
reserved TTBR0_EL1 followed by the ASID=0 update in TTBR1_EL1. If an
exception occurs between these two, the exception return code will
re-instate a valid TTBR0_EL1. Similar scenario can happen in
cpu_switch_mm() between setting the reserved TTBR0_EL1 and the ASID
update in cpu_do_switch_mm().

This patch reverts the entry.S check for ASID == 0 to TTBR0_EL1 and
disables the interrupts around the TTBR0_EL1 and ASID switching code in
__uaccess_ttbr0_disable(). It also ensures that, when returning from the
EFI runtime services, efi_set_pgd() doesn't leave a non-zero ASID in
TTBR1_EL1 by using uaccess_ttbr0_{enable,disable}.

The accesses to current_thread_info()->ttbr0 are updated to use
READ_ONCE/WRITE_ONCE.

As a safety measure, __uaccess_ttbr0_enable() always masks out any
existing non-zero ASID TTBR1_EL1 before writing in the new ASID.

Fixes: 27a921e75711 ("arm64: mm: Fix and re-enable ARM64_SW_TTBR0_PAN")
Acked-by: Will Deacon <will.deacon@arm.com>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Co-developed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: mm: Add additional parameter to uaccess_ttbr0_enable

Add an extra temporary register parameter to uaccess_ttbr0_enable which
is about to be required for arm64 PAN support.

This patch doesn't introduce any functional change but ensures that the
kernel compiles once the KVM/ARM tree is merged with the arm64 tree by
ensuring a trivially mergable conflict with commit
27a921e75711d924617269e0ba4adb8bae9fd0d1
("arm64: mm: Fix and re-enable ARM64_SW_TTBR0_PAN").

Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

arm64: KVM: Add invalidate_icache_range helper

We currently tightly couple dcache clean with icache invalidation,
but KVM could do without the initial flush to PoU, as we've
already flushed things to PoC.

Let's introduce invalidate_icache_range which is limited to
invalidating the icache from the linear mapping (and thus
has none of the userspace fault handling complexity), and
wire it in KVM instead of flush_icache_range.

Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

arm64: mm: Fix and re-enable ARM64_SW_TTBR0_PAN

With the ASID now installed in TTBR1, we can re-enable ARM64_SW_TTBR0_PAN
by ensuring that we switch to a reserved ASID of zero when disabling
user access and restore the active user ASID on the uaccess enable path.

Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Tested-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64: Implement pmem API support

Add a clean-to-point-of-persistence cache maintenance helper, and wire
up the basic architectural support for the pmem driver based on it.

Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[catalin.marinas@arm.com: move arch_*_pmem() functions to arch/arm64/mm/flush.c]
[catalin.marinas@arm.com: change dmb(sy) to dmb(osh)]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: Convert __inval_cache_range() to area-based

__inval_cache_range() is already the odd one out among our data cache
maintenance routines as the only remaining range-based one; as we're
going to want an invalidation routine to call from C code for the pmem
API, let's tweak the prototype and name to bring it in line with the
clean operations, and to make its relationship with __dma_inv_area()
neatly mirror that of __clean_dcache_area_poc() and __dma_clean_area().
The loop clearing the early page tables gets mildly massaged in the
process for the sake of consistency.

Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: don't pull uaccess.h into *.S

Split asm-only parts of arm64 uaccess.h into a new header and use that
from *.S.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Replace <asm/uaccess.h> with <linux/uaccess.h> globally

This was entirely automated, using the script by Al:

PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)

to do the replacement at the end of the merge window.

Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arm64: Disable TTBR0_EL1 during normal kernel execution

When the TTBR0 PAN feature is enabled, the kernel entry points need to
disable access to TTBR0_EL1. The PAN status of the interrupted context
is stored as part of the saved pstate, reusing the PSR_PAN_BIT (22).
Restoring access to TTBR0_EL1 is done on exception return if returning
to user or returning to a context where PAN was disabled.

Context switching via switch_mm() must defer the update of TTBR0_EL1
until a return to user or an explicit uaccess_enable() call.

Special care needs to be taken for two cases where TTBR0_EL1 is set
outside the normal kernel context switch operation: EFI run-time
services (via efi_set_pgd) and CPU suspend (via cpu_(un)install_idmap).
Code has been added to avoid deferred TTBR0_EL1 switching as in
switch_mm() and restore the reserved TTBR0_EL1 when uninstalling the
special TTBR0_EL1.

User cache maintenance (user_cache_maint_handler and
__flush_cache_user_range) needs the TTBR0_EL1 re-instated since the
operations are performed by user virtual address.

This patch also removes a stale comment on the switch_mm() function.

Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: mm: convert __dma_* routines to use start, size

__dma_* routines have been converted to use start and size instread of
start and end addresses. The patch was origianlly for adding
__clean_dcache_area_poc() which will be used in pmem driver to clean
dcache to the PoC(Point of Coherency) in arch_wb_cache_pmem().

The functionality of __clean_dcache_area_poc() was equivalent to
__dma_clean_range(). The difference was __dma_clean_range() uses the end
address, but __clean_dcache_area_poc() uses the size to clean.

Thus, __clean_dcache_area_poc() has been revised with a fallthrough
function of __dma_clean_range() after the change that __dma_* routines
use start and size instead of using start and end.

As a consequence of using start and size, the name of __dma_* routines
has also been altered following the terminology below:
area: takes a start and size
range: takes a start and end

Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@sk.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64: fix "dc cvau" cache operation on errata-affected core

The ARM errata 819472, 826319, 827319 and 824069 for affected
Cortex-A53 cores demand to promote "dc cvau" instructions to
"dc civac" as well.
Attribute the usage of the instruction in __flush_cache_user_range
to also be covered by our alternative patching efforts.
For that we introduce an assembly macro which both deals with
alternatives while still tagging the instructions as USER.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: Fold proc-macros.S into assembler.h

To allow the assembler macros defined in arch/arm64/mm/proc-macros.S to
be used outside the mm code move the contents of proc-macros.S to
asm/assembler.h. Also, delete proc-macros.S, and fix up all references
to proc-macros.S.

Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
[rebased, included dcache_by_line_op]
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64: Use PoU cache instr for I/D coherency

In systems with three levels of cache(PoU at L1 and PoC at L3),
PoC cache flush instructions flushes L2 and L3 caches which could affect
performance.
For cache flushes for I and D coherency, PoU should suffice.
So changing all I and D coherency related cache flushes to PoU.

Introduced a new __clean_dcache_area_pou API for dcache flush till PoU
and provided a common macro for __flush_dcache_area and
__clean_dcache_area_pou.

Also, now in __sync_icache_dcache, icache invalidation for non-aliasing
VIPT icache is done only for that particular page instead of the earlier
__flush_icache_all.

Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ashok Kumar <ashoks@broadcom.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64: use ENDPIPROC() to annotate position independent assembler routines

For more control over which functions are called with the MMU off or
with the UEFI 1:1 mapping active, annotate some assembler routines as
position independent. This is done by introducing ENDPIPROC(), which
replaces the ENDPROC() declaration of those routines.

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: mm: Adopt new alternative assembler macros

Convert the dynamic patching for ARM64_WORKAROUND_CLEAN_CACHE over to
the newly added alternative assembler macros.

Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64: alternative: Merge alternative-asm.h into alternative.h

asm/alternative-asm.h and asm/alternative.h are extremely similar,
and really deserve to live in the same file (as this makes further
modufications a bit easier).

Fold the content of alternative-asm.h into alternative.h, and
update the few users.

Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: kill flush_cache_all()

The documented semantics of flush_cache_all are not possible to provide
for arm64 (short of flushing the entire physical address space by VA),
and there are currently no users; KVM uses VA maintenance exclusively,
cpu_reset is never called, and the only two users outside of arch code
cannot be built for arm64.

While cpu_soft_reset and related functions (which call flush_cache_all)
were thought to be useful for kexec, their current implementations only
serve to mask bugs. For correctness kexec will need to perform
maintenance by VA anyway to account for system caches, line migration,
and other subtleties of the cache architecture. As the extent of this
cache maintenance will be kexec-specific, it should probably live in the
kexec code.

This patch removes flush_cache_all, and related unused components,
preventing further abuse.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Geoff Levand <geoff@infradead.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: compat: align cacheflush syscall with arch/arm

Update handling of cacheflush syscall with changes made in arch/arm
counterpart:
- return error to userspace when flushing syscall fails
- split user cache-flushing into interruptible chunks
- don't bother rounding to nearest vma

Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
[will: changed internal return value from -EINTR to 0 to match arch/arm/]
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64: add Cortex-A53 cache errata workaround

The ARM errata 819472, 826319, 827319 and 824069 define the same
workaround for these hardware issues in certain Cortex-A53 parts.
Use the new alternatives framework and the CPU MIDR detection to
patch "cache clean" into "cache clean and invalidate" instructions if
an affected CPU is detected at runtime.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[will: add __maybe_unused to squash gcc warning]
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64: mm: use inner-shareable barriers for inner-shareable maintenance

In order to ensure ordering and completion of inner-shareable maintenance
instructions (cache and TLB) on AArch64, we can use the -ish suffix to
the dmb and dsb instructions respectively.

This patch updates our low-level cache and tlb maintenance routines to
use the inner-shareable barrier variants where appropriate.

Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: Fix DMA range invalidation for cache line unaligned buffers

If the buffer needing cache invalidation for inbound DMA does start or
end on a cache line aligned address, we need to use the non-destructive
clean&invalidate operation. This issue was introduced by commit
7363590d2c46 (arm64: Implement coherent DMA API based on swiotlb).

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Jon Medhurst (Tixy) <tixy@linaro.org>

arm64: Relax the kernel cache requirements for boot

With system caches for the host OS or architected caches for guest OS we
cannot easily guarantee that there are no dirty or stale cache lines for
the areas of memory written by the kernel during boot with the MMU off
(therefore non-cacheable accesses).

This patch adds the necessary cache maintenance during boot and relaxes
the booting requirements.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: remove unnecessary cache flush at boot

Currently we flush the entire dcache at boot within __cpu_setup, but
this is unnecessary as the booting protocol demands that the dcache is
invalid and off upon entering the kernel. The presence of the cache
flush only serves to hide bugs in bootloaders, and is not safe in the
presence of SMP.

In an SMP boot scenario the CPUs enter coherency outside of the kernel,
and the primary CPU enables its caches before bringing up secondary
CPUs. Therefore if any secondary CPU has an entry in its cache (in
violation of the boot protocol), the primary CPU might snoop it even if
the secondary CPU's cache is disabled. The boot-time cache flush only
serves to hide a firmware bug, and slows down a cpu boot unnecessarily.

This patch removes the unnecessary boot-time cache flush.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
[catalin.marinas@arm.com: make __flush_dcache_all local only]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: Implement coherent DMA API based on swiotlb

This patch adds support for DMA API cache maintenance on SoCs without
hardware device cache coherency.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: mm: fix the function name in comment of __flush_dcache_area

Fix the function name of comment of __flush_dcache_area,
because __flush_dcache_area is the correct name. Also,
the missing variable 'size' is added to the comment.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: mm: Fix operands of clz in __flush_dcache_all

The format of the lower 32-bits of the 64-bit operand to 'dc cisw' is
unchanged from ARMv7 architecture and the upper bits are RES0. This
implies that the 'way' field of the operand of 'dc cisw' occupies the
bit-positions [31 .. (32-A)]. Due to the use of 64-bit extended operands
to 'clz', the existing implementation of __flush_dcache_all is incorrectly
placing the 'way' field in the bit-positions [63 .. (64-A)].

Signed-off-by: Sukanto Ghosh <sghosh@apm.com>
Tested-by: Anup Patel <anup.patel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: stable@vger.kernel.org

arm64: Cache maintenance routines

The patch adds functionality required for cache maintenance. The AArch64
architecture mandates non-aliasing VIPT or PIPT D-cache and VIPT (may
have aliases) or ASID-tagged VIVT I-cache. Cache maintenance operations
are automatically broadcast in hardware between CPUs.

Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>