arm64: dts: exynos: add 'chassis-type' property

A new 'chassis-type' root node property has recently been approved for
the device-tree specification.

Add this property for end-user devices (such as laptops,
smartphones and tablets) based on Samsung Exynos ARM64 SoCs.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211017101228.19478-1-krzysztof.kozlowski@canonical.com

arm64: dts: exynos: Rename Samsung and Exynos to lowercase

Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.

"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.

The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.

Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).

Link: https://lore.kernel.org/r/20200117190305.5257-1-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

arm64: dts: exynos: configure GSCALER related clocks on TM2

GSCALER should be feed with clock at certain rates. Configure it on
Exynos5433 based TM2 board.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Add SPDX license identifiers

Replace GPL v2.0 license statements with SPDX license identifiers.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Remove the te-gpios property in the TM2 boards

The decon uses HW-TRIGGER, so TE interrupt is not necessary.
Therefore, remove the te-gpios property in the TM2 dts.

Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

ARM: dts: exynos: Use - instead of @ for DT OPP entries

Compiling the DT file with W=1, DTC warns like follows:

Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property

Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.

Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
[k.kozlowski: Split patch per ARM and ARM64]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board

This patch add the panel device tree node for S6E3HA2 display
controller to TM2 dts.

Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Add stmfts touchscreen node for TM2 and TM2E

TM2 and TM2E devices are provided with a ST-Microelectronics
Finger Tip S device with small differences:

- screen size
- TM2E uses the stmfts also as a touchkey for "back" and "menu"

In this commit the initial value of the interrupt line is set to
EXYNOS_PIN_PULL_UP as the interrupt is triggered when the line
goes down.

Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e

Add initial clock configuration for display subsystem for Exynos5433
based TM2/TM2e boards in device tree in order to avoid dependency on the
configuration left by the bootloader. This initial configuration is also
needed to ensure that display subsystem is operational if display power
domain gets turned off before clock controller is probed and the inital
clock configuration left by the bootloader saved.

TM2 and TM2e uses different rate for DISP PLL clock, but for better
maintainability all 'assigned-clocks-*' properties for DISP CMU are
defines in each board dts instead of redefining the rates property.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Add TM2 touchkey node

Add DT node for TM2 touchkey device.

Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Make TM2 and TM2E independent from each other

Currently TM2E dts includes TM2 but there are some differences
between the two boards and TM2 has some properties that TM2E
doesn't have.

That's why it's important to keep the two dts files independent
and put all the commonalities in a tm2-common.dtsi file.

At the current status the only two differences between the two
dts files (besides the board name) are ldo31 and ldo38.

Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Fix wrong values for ldo23 and ldo25 on TM2/TM2E

This patch fixes wrong values assigned to ldo23 and ldo25 on both TM2 and TM2E.

Fixes: 01e5d2352152 ("arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Comply to the samsung pinctrl naming convention in TM2

Change the PIN() macro definition so that it can use the macros
from pinctrl/samsung.h header file.

Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Add support of bus frequency using VDD_INT on Exynos5433 TM2

This patch adds the bus Device-tree nodes for INT (Internal) block
and enables the bus frequency scaling.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Enable HS400 mode for eMMC for TM2

TM2 can support the HS400 mode, but eMMC is working in the lowest mode.
This patch adds the properties for HS400 and other modes.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Add the mshc_2 node for supporting T-Flash

Add the mshc_2 node for supporting T-Flash.

Also add the "mshc*" aliases. dwmmc driver should be assigned to
"ctrl_id" after parsing to "mshc". If there are no aliases for mshc,
then it might be set to the wrong capabilities.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: TM2 - add support for MFC video codec device

This patch adds device nodes for MFC video codec device to Exynos5433 SoC
dtsi and proper initial clock configuration to TM2 dts.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: TM2 - add support for JPEG codec device

This patch adds device nodes for JPEG codec device to Exynos5433 SoC dtsi
and proper initial clock configuration to TM2 dts.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: TM2 - add support for GScaler devices

This patch adds device nodes for GScaler devices to Exynos5433 SoC dtsi
and proper initial clock configuration to TM2 dts.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: TM2 - remove unused UART3 and set clocks directly on CMU

UART3 device is not really needed for enabling audio block on TM2.
Enabling it made it working by enabling some common parent clocks,
what is now handled by improved exynos5433 clocks driver. Thus the UART3
device node can be safely disabled. The assigned-clocks entries are
however still needed, so move them under the respective CMU node.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Assign parent clock of the clkout clock for TM2 board

Without this patch the clkout clock is orphaned and sound doesn't
work properly.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Move FSYS CMU configuration from Exynos5433 dtsi to TM2 dts

Move initial FSYS CMU (related to USB 3.0 devices) clocks configuration
from generic exynos5433.dtsi file to exynos5433-tm2.dts, as this is
a board specific item.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board

This patch adds the Device Tree source for Exynos5433-based Samsung TM2
board.

This patch adds support for following devices:
1. basic SoC
- Initial booting for Samsung Exynos5433 SoC
- DRAM LPDDR3 (3GB)
- eMMC (32GB)
- ARM architecture timer

2. power management devices
- Sasmung S2MPS13 PMIC for the power supply
- CPUFREQ for big.LITTLE cores
- TMU for big.LITTLE cores and GPU
- ADC with thermistor to measure the temperature of AP/Battery/Charger
- Maxim MAX77843 Interface PMIC (MUIC/Haptic/Regulator)

3. sound devices
- I2S for sound bus
- LPASS for sound power control
- Wolfson WM5110 for sound codec
- Maxim MAX98504 for speaker amplifier
- TM2 ASoC Machine device driver node

3. display devices
- DECON, DSI and MIC for the panel output

4. USB devices
- USB 3.0 DRD (Dual Role Device)
- USB 3.0 Host controller

5. storage devices
- MSHC (Mobile Storage Host Controller) for eMMC device

6. misc devices
- gpio-keys (power, volume up/down, home key)
- PWM (Pulse Width Modulation Timer)

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Ingi kim <ingi2.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>