arm64: dts: meson-sm1: Fix the pwm regulator supply properties

After enabling CONFIG_REGULATOR_DEBUG=y we observe below debug logs.
Changes help link VDDCPU pwm regulator to 12V regulator supply
instead of dummy regulator.

[ 11.602281] pwm-regulator regulator-vddcpu: Looking up pwm-supply property
in node /regulator-vddcpu failed
[ 11.602344] VDDCPU: supplied by regulator-dummy
[ 11.602365] regulator-dummy: could not add device link regulator.11: -ENOENT
[ 11.602548] VDDCPU: 721 <--> 1022 mV at 1022 mV, enabled

Fixes: 88d537bc92ca ("arm64: dts: meson: convert meson-sm1-odroid-c4 to dtsi")
Fixes: 700ab8d83927 ("arm64: dts: khadas-vim3: add support for the SM1 based VIM3L")
Fixes: 3d9e76483049 ("arm64: dts: meson-sm1-sei610: enable DVFS")
Fixes: 976e920183e4 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts")

Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210919202918.3556-4-linux.amoon@gmail.com

arm64: dts: meson: vim3: enable hdmi audio loopback

Enable audio capture frontends and a tdm decoder.
This makes it possible to loopback the audio played on the hdmi codec,
which is the only output interface at the moment.

Of course, one TODDR device would be enough to do that but since
the 3 FRDDRs are enabled on the playback side, let's do the same on the
capture side.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210429084253.59692-1-jbrunet@baylibre.com

arm64: dts: meson: fix broken wifi node for Khadas VIM3L

move &sd_emmc_a ... from /* */ commented area, because cant load wifi fw
without sd-uhs-sdr50 option on VIM3L

[ 11.686590] brcmfmac: brcmf_chip_cores_check: CPU core not detected
[ 11.696382] brcmfmac: brcmf_sdio_probe_attach: brcmf_chip_attach failed!
[ 11.706240] brcmfmac: brcmf_sdio_probe: brcmf_sdio_probe_attach failed
[ 11.715890] brcmfmac: brcmf_ops_sdio_probe: F2 error, probe failed -19...
[ 13.718424] brcmfmac: brcmf_chip_recognition: chip backplane type 15 is not supported

Signed-off-by: Artem Lapkin <art@khadas.com>
Fixes: f1bb924e8f5b ("arm64: dts: meson: fix mmc0 tuning error on Khadas VIM3")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20210129085041.1408540-1-art@khadas.com

arm64: dts: meson: vim3l: remove sound card definition

The sound card definition should have been removed when the common
definition was added to the vim3 dtsi but this slips through.
Remove it now.

Fixes: 7c9c06246cea ("arm64: dts: meson: vim3: make sound card common to all variants")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200828154435.419561-1-jbrunet@baylibre.com

arm64: dts: meson: fix mmc0 tuning error on Khadas VIM3

Similar to other G12B devices using the W400 dtsi, I see reports of mmc0
tuning errors on VIM3 after a few hours uptime:

[12483.917391] mmc0: tuning execution failed: -5
[30535.551221] mmc0: tuning execution failed: -5
[35359.953671] mmc0: tuning execution failed: -5
[35561.875332] mmc0: tuning execution failed: -5
[61733.348709] mmc0: tuning execution failed: -5

I do not see the same on VIM3L, so remove sd-uhs-sdr50 from the common dtsi
to silence the error, then (re)add it to the VIM3L dts.

Fixes: 4f26cc1c96c9 ("arm64: dts: khadas-vim3: move common nodes into meson-khadas-vim3.dtsi")
Fixes: 700ab8d83927 ("arm64: dts: khadas-vim3: add support for the SM1 based VIM3L")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200721015950.11816-1-christianshewitt@gmail.com

arm64: dts: meson: add audio playback to khadas-vim3l

Add initial audio support limited to HDMI i2s, copying the config
from the existing VIM3 device-tree.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200718072532.8427-3-christianshewitt@gmail.com

arm64: dts: khadas-vim3: add commented support for PCIe

The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between
the USB3.0 controller and the PCIe Controller, thus only
a single controller can use it.

The needed DT configuration when the MCU is configured to mux
the PCIe/USB3.0 differential lines to the M.2 Key M slot is
added commented and may be uncommented to disable USB3.0 from the
USB Complex and enable the PCIe controller.

The End User is not expected to uncomment the following except for
testing purposes, but instead rely on the firmware/bootloader to
update these nodes accordingly if PCIe mode is selected by the MCU.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>

arm64: dts: khadas-vim3: add commented support for PCIe

The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between
the USB3.0 controller and the PCIe Controller, thus only
a single controller can use it.

The needed DT configuration when the MCU is configured to mux
the PCIe/USB3.0 differential lines to the M.2 Key M slot is
added commented and may be uncommented to disable USB3.0 from the
USB Complex and enable the PCIe controller.

The End User is not expected to uncomment the following except for
testing purposes, but instead rely on the firmware/bootloader to
update these nodes accordingly if PCIe mode is selected by the MCU.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

arm64: dts: khadas-vim3: add support for the SM1 based VIM3L

Add the Amlogic SM1 based Khadas VIM3L, sharing all the same features
as the G12B based VIM3, but:
- a different DVFS support since only a single cluster is available
- audio is still not available on SM1

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>