arm64: dts: amlogic: correct gpio-keys properties

gpio-keys children do not use unit addresses.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220609113911.380368-6-krzysztof.kozlowski@linaro.org

arm64: dts: meson: fix PHY deassert timing requirements

According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. This fixes an issue seen on ODROID-C2 where the Ethernet
link doesn't come up when using ip link set down/up:
[ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down
[ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36)
[ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma
[ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed

Fixes: f29cabf240ed ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/4a322c198b86e4c8b3dda015560a683babea4d63.1607363522.git.stefan@agner.ch

arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings

The snps,reset-gpio bindings are deprecated in favour of the generic
"Ethernet PHY reset" bindings.

Replace snps,reset-gpio from the &ethmac node with reset-gpios in the
ethernet-phy node. The old snps,reset-active-low property is now encoded
directly as GPIO flag inside the reset-gpios property.

snps,reset-delays-us is converted to reset-assert-us and
reset-deassert-us. reset-assert-us is the second cell from
snps,reset-delays-us while reset-deassert-us was the third cell.

Instead of blindly copying the old values (which seems strange since
they gave the PHY one second to come out of reset) over this also
updates the delays based on the datasheets:
- the Realtek RTL8211F PHY needs a 10ms assert delay (the datasheet
mentions: "For a complete PHY reset, this pin must be asserted low
for at least 10ms") and a 30ms deassert delay (the datasheet
mentions: "Wait for a further 30ms (for internal circuits settling
time) before accessing the PHY register". This applies to the
following boards: GXBB NanoPi K2, GXBB Odroid-C2, GXBB Vega S95
variants, GXBB Wetek variants, GXL P230, GXM Khadas VIM2, GXM Nexbox
A1, GXM Q200, GXM RBox Pro boards.
- the ICPlus IP101GR PHY needs a 10ms assert delay (the datasheet
mentions: "Trst | Reset period | 10ms") and a deassert delay of 10ms
as well (the datasheet mentions: "Tclk_MII_rdy | MII/RMII clock
output ready after reset released | 10ms"). This applies to the GXBB
Nexbox A95X board.
- the Micrel KSZ9031 seems to require a 100us delay but use the same
(seemingly safe) values from RTL8211F due to lack of a board to verify
this. This applies to the GXBB P200 board.

The GXBB P201 board is left out from this conversion because it doesn't
have a dedicated PHY node (because it's not clear which PHY is used on
that board).

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

arm64: dts: amlogic: remove ethernet-phy-idAAAA.BBBB compatible strings

The Ethernet PHY documentation
(Documentation/devicetree/bindings/net/phy.txt) states that:
If the PHY reports an incorrect ID (or none at all) then the
"compatible" list may contain an entry with the correct PHY ID in the
form: "ethernet-phy-idAAAA.BBBB"

An older version of the documentation suggested that the compatible
string can be used when the PHY ID is known.

Remove the ethernet-phy-id compatible string and add a comment with the
PHY ID instead.
This is a no-op on boards which are shipped with the PHY that was
listed (= all known cases). However, if a board manufacturer decides to
ship a different PHY we will now load and use the correct driver because
we ask the PHY to identify itself.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

arm64: dts: meson: p230: disable advertisement EEE for GbE.

This patch disable EEE advertisement for P230 board (DWMAC + RTL8211F).
If not disable it, the network connection is not stable, will got issues
like throughput drop or broken link.

Signed-off-by: He Yangxuan <yangxuan8282@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

ARM64: dts: meson-gx-p23x-q20x: move the wifi node to each board's .dts

meson-gx-p23x-q20x.dtsi is currently used by five boards:
- Amlogic P230 and P231 (which should be identical, apart from the
external RGMII PHY on P230 whereas P231 can only use the internal PHY)
- Amlogic Q200 (identical to P230 but with an S912 GXM SoC instead of a
GXL S905D SoC) and Q201 (identical to P231 but with an S912 GXM SoC
instead of a GXL S905D SoC)
- NEXBOX A1 (based on the S912 GXM SoC)

The Amlogic P230 board uses a Broadcom BCM4356 SDIO wifi chip. Since the
other Amlogic reference design boards are very similar it's safe to
assume that these also use a Broadcom based SDIO wifi chip (which is
also how it was configured in meson-gx-p23x-q20x.dtsi).

However, NEXBOX A1 comes with a "longsys LTM8830" SDIO wifi module,
which is based on the "Qualcomm Atheros QCA9377-3(QCA1023-0)" chipset.

Thus move the wifi node from meson-gx-p23x-q20x.dtsi to each of the
four Amlogic reference board's .dts files.
There are no devicetree bindings for the QCA9377 SDIO wifi module yet,
so nothing is added to meson-gxm-nexbox-a1.dts.

Fixes: f51b454549b812 ("ARM64: dts: meson-gxm: Add support for the Nexbox A1")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

ARM64: dts: meson: enable the saradc node in meson-gx-p23x-q20x.dtsi

meson-gxl-s905d-p230.dts and meson-gxm-q200.dts enable the saradc node
(and configure it's vref-supply "VDDIO_AO18") in their corresponding
.dts file.
Move both (the saradc node as well as the VDDIO_AO18 regulator) to
remove some duplicate code.

As a positive side-effect this enables the saradc also for the P231 (GXL
S905D) and Q201 (GXM S912) development boards which are similar to the
P230/Q200 boards (P231 and Q201 use the internal 100Mbit/s PHY, while
P230 and Q200 have an external RGMII PHY).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

ARM64: dts: amlogic: Convert to new-style SPDX license identifiers

Move the SPDX-License-Identifier lines to the top and drop the
license splat.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

ARM64: dts: meson-gx: add external PHY interrupt on some platforms

Add the external PHY interrupt on the nanopi-k2, odroid-c2, p200, p230
and q200

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

ARM64: dts: meson-gx: Add AO CEC nodes

This patch adds the AO CEC node in all the HDMI enabled boards DTS.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

ARM64: dts: meson-gxl-s905d-p230: Add HDMI nodes

Add HDMI nodes for the Amlogic P230 board.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

ARM64: dts: meson-gx: Add Buttons to Q200 and P230 boards

This patch adds support for the P230 and Q200 ADC laddered button and
GPIO button.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

ARM64: dts: amlogic: add the ethernet TX delay configuration

This adds the amlogic,tx-delay-ns property with the old (hardcoded)
default value of 2ns to all boards which are using an RGMII ethernet
PHY.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

ARM64: dts: Add support for Meson GXM

Following the Amlogic Linux kernel, it seem the only differences
between the GXL and GXM SoCs are the CPU Clusters.

This commit renames the gxl-s905d-p23x DTSI in a common file for
S905D p23x and S912 q20x boards.

Then adds a meson-gxm dtsi and reproduce the P23x to Q20x boards
dts files since the S905D and S912 SoCs shares the same pinout
and the P23x and Q20x boards are identical.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

ARM64: dts: meson-gxl-p23x: Enable ethernet

Enable Ethernet on the p23x board, pinctrl attribute is only added for
the p230 board since the p231 only uses the Internal PHY.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

ARM64: dts: amlogic: Add basic support for Amlogic S905D

This patch introduces the basic support for the Amlogic S905D (MesonGXL)
and for the Amlogic evaluation boards P230 and P231.
No documentation has been released yet for this SoC, so for now only the
bare minimum has been added in the DT.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>