arm64: dts: amlogic: replace underscores in node names

Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens.

Cc: Marc Gonzalez <mgonzalez@freebox.fr>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240213143217.336341-1-krzysztof.kozlowski@linaro.org
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>

arm64: dts: Replace the IRQ number with the IRQID macro definition

Replacing IRQ numbers with IRQID macro definitions makes node properties
easier to understand and also makes GPIO interrupts easier to use.

Associated platforms:
- Amlogic Meson-G12A
- Amlogic Meson-G12B
- Amlogic Meson-SM1

Signed-off-by: Huqiang Qin <huqiang.qin@amlogic.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230724060108.1403662-4-huqiang.qin@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

arm64: dts: meson-g12b: Fix the pwm regulator supply properties

After enabling CONFIG_REGULATOR_DEBUG=y we observer below debug logs.
Changes help link VDDCP_A and VDDCPU_B pwm regulator to 12V regulator
supply instead of dummy regulator.

[ 4.147196] VDDCPU_A: will resolve supply early: pwm
[ 4.147216] pwm-regulator regulator-vddcpu-a: Looking up pwm-supply from device tree
[ 4.147227] pwm-regulator regulator-vddcpu-a: Looking up pwm-supply property in node /regulator-vddcpu-a failed
[ 4.147258] VDDCPU_A: supplied by regulator-dummy
[ 4.147288] regulator-dummy: could not add device link regulator.12: -ENOENT
[ 4.147353] VDDCPU_A: 721 <--> 1022 mV at 871 mV, enabled
[ 4.152014] VDDCPU_B: will resolve supply early: pwm
[ 4.152035] pwm-regulator regulator-vddcpu-b: Looking up pwm-supply from device tree
[ 4.152047] pwm-regulator regulator-vddcpu-b: Looking up pwm-supply property in node /regulator-vddcpu-b failed
[ 4.152079] VDDCPU_B: supplied by regulator-dummy
[ 4.152108] regulator-dummy: could not add device link regulator.13: -ENOENT

Fixes: c6d29c66e582 ("arm64: dts: meson-g12b-khadas-vim3: add initial device-tree")
Fixes: d14734a04a8a ("arm64: dts: meson-g12b-odroid-n2: enable DVFS")
Fixes: 3cb74db9b256 ("arm64: dts: meson: convert ugoos-am6 to common w400 dtsi")

Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210919202918.3556-3-linux.amoon@gmail.com

arm64: dts: meson: g12b: w400: fix PHY deassert timing requirements

According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
egisters. On similar boards with the same PHY this fixes an issue where
Ethernet link would not come up when using ip link set down/up.

Fixes: 2cd2310fca4c ("arm64: dts: meson-g12b-ugoos-am6: add initial device-tree")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/46298e66572784c44f873f1b71cc4ab3d8fc5aa6.1607363522.git.stefan@agner.ch

arm64: dts: meson: misc fixups for w400 dtsi

Current devices using the W400 dtsi show mmc tuning errors:

[12483.917391] mmc0: tuning execution failed: -5
[30535.551221] mmc0: tuning execution failed: -5
[35359.953671] mmc0: tuning execution failed: -5
[35561.875332] mmc0: tuning execution failed: -5
[61733.348709] mmc0: tuning execution failed: -5

Removing "sd-uhs-sdr50" from the SDIO node prevents this. We also add
keep-power-in-suspend to the SDIO node and fix an indentation.

Fixes: 3cb74db9b256 ("arm64: dts: meson: convert ugoos-am6 to common w400 dtsi")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200721013952.11635-1-christianshewitt@gmail.com

arm64: dts: meson: convert ugoos-am6 to common w400 dtsi

Convert the Ugoos AM6 dts into meson-g12b-w400.dtsi, and then create
a new AM6 dts that references it. This is in preparation for several
new G12B devices that will share the common w400 dtsi.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200520014329.12469-2-christianshewitt@gmail.com