arm64: dts: allwinner: Use the new r_intc binding

The binding of R_INTC was updated to allow specifying interrupts other
than the external NMI, since routing those interrupts through the R_INTC
driver allows using them for wakeup.

Update the device trees to use the new binding.

Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

ARM: dts: sunxi: Fix the LED node names

According to the LED bindings, the LED node names are supposed to be led
plus an optional suffix. Let's fix our users to use that new scheme.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210114113538.1233933-6-maxime@cerno.tech

arm64: dts: allwinner: Pine H64: Enable HS200 eMMC mode

The eMMC modules offered for the Pine64 boards are capable of the HS200
eMMC speed mode, when observing the frequency limit of 150 MHz.

Enable that in the DT.

This increases the interface speed from ~80 MB/s to ~120 MB/s.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-9-andre.przywara@arm.com

arm64: dts: allwinner: Pine H64: Enable both RGMII RX/TX delay

Since commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"),
the network is unusable on PineH64 model A.

This is due to phy-mode incorrectly set to rgmii instead of rgmii-id.

Fixes: 729e1ffcf47e ("arm64: allwinner: h6: add support for the Ethernet on Pine H64")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201019063449.33316-1-clabbe@baylibre.com

arm64: dts: allwinner: h6: Enable CPU opp tables for Pine H64

Enable CPU and GPU opp tables for Pine H64.

This needs to change the CPU regulator max voltage to fit
the OPP table.

Also add the ramp-delay information to avoid any out of spec
running as the regulator is slower at reaching the voltage
requested compare to the PLL reaching the frequency.

There is no such information for AXP805 but similar PMIC (AXP813)
has a DVM (Dynamic Voltage scaling Management) ramp rate equal
to 2500uV/us.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: Sort Pine H64 device-tree nodes

Pine H64 device-tree have some nodes not properly sorted.

Fix this.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: h6: Move ext. oscillator to board DTs

It turns out that not all H6 boards have external 32kHz oscillator.
Currently the only one known such H6 board is Tanix TX6.

Move external oscillator node from common H6 dtsi to board specific dts
files where present.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: h6: Pine H64: Add SPI flash node

The Pine H64 board comes with SPI flash soldered on the board, connected
to the SPI0 pins (so it can also boot from there).

Add the required SPI flash DT node to describe this.

Unfortunately the SPI CS0 pin collides with the eMMC CMD pin, so we can't
use both eMMC and SPI flash at the same time (the first to claim the pin
would win, the other's probe routine would then fail).

To avoid losing the more useful eMMC device by chance, mark the SPI
device as "disabled" for now. A user or some U-Boot code could fix this
up if needed, for instance if no eMMC has been detected (it's socketed).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: unify header comment style

Allwinner device tree files used different comment style for
copyright notice.

Update this to keep a coherency.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwiner: Fix typo in dual licensed SPDX identifier

With dual licensed SPDX identifier the "OR" should
be uppercase.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: sun50i-h6-pine-h64: state that the DT supports the modelA

The current sun50i-h6-pine-h64 DT does not specify which model (A or B)
it supports.
When this file was created, only modelA was existing, but now both model
exists and with the time, this DT drifted to support the model B since it is
the most common one.
Furtheremore, some part of the model A does not work with it like ethernet and
HDMI connector (as confirmed by Jernej on IRC).

So it is time to settle the issue, and the easiest way was to state that
this DT is for model B.
Easiest since only a small name changes is required.
Doing the opposite (stating this file is for model A) will add changes (for
ethernet and HDMI) and so, will break too many setup.

But as asked by the maintainer this patch state this file is for model A.
In the process this patch adds the missing compoments to made it work on
model A.

Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: Add mali GPU supply for H6 boards

Enable and add supply to the Mali GPU node on all the
H6 boards.

Regarding the datasheet the maximum time for supply to reach
its voltage is 32ms.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: h6: Enable IR on H6 boards

Beelink GS1, OrangePi H6 boards and Pine H64 have an IR receiver.

Enable it in their device-tree.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: dts: allwinner: h6: Pine H64: Add interrupt line for RTC

The external PCF8563 RTC chip's interrupt line is connected to the NMI
line on the SoC.

Add the interrupt line to the device tree.

Fixes: 17ebc33afc35 ("arm64: allwinner: h6: add PCF8563 RTC on Pine H64 board")
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

arm64: dts: allwinner: h6: add PIO VCC bank supplies for Pine H64

The Allwinner H6 SoC features tweakable VCC for PC, PD, PG, PL and PM
banks.

This patch adds supplies for these banks except PL bank. PL bank is
where PMIC is attached, and currently if a PMIC regulator is added
for it a dependency loop will happen.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: dts: allwinner: h6: move MMC pinctrl to dtsi

There is only one pinmuxing available for each MMC controller.

Move the pinctrl to the SOC

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: dts: allwinner: h6: enable USB2 on Pine H64

Pine H64 board has both the USB2 OTG pins and the USB2 host pins on H6
SoC wired out to USB Type-A ports.

Enable them.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

arm64: dts: allwinner: h6: add USB Vbus regulator for Pine H64

The 5V output of the USB ports on Pine H64 is controlled via a GPIO.

Add the USB Vbus regulator device tree node.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

arm64: dts: allwinner: h6: Enable HDMI output on Pine H64 board

Pine H64 board has HDMI type A connector.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: allwinner: h6: add support for the Ethernet on Pine H64

The Pine H64 board has an Ethernet port, which is connected to a
RTL8211E PHY, then the PHY is connected to the MAC on H6 SoC.

Add support for the Ethernet port.

The PHY needs some time to start up, and the time is modelled as enable
ramp delay of the regulator.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: allwinner: dts: h6: fix Pine H64 MMC bus width

Currently the enabled MMC controllers on Pine H64 do not have bus-width
set, which make them fall back to 1-bit mode and become quite slow.

Fix this by add the corresponding bus-width properties.

Fixes: ecbd611882a1 ("arm64: allwinner: h6: enable MMC0/2 on Pine H64")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: allwinner: h6: enable MMC0/2 on Pine H64

The Pine H64 board have a MicroSD slot connected to MMC0 controller of
the H6 SoC and a eMMC slot connected to MMC2.

Enable them in the device tree.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: dts: allwinner: h6: enable AXP805 PMIC on Pine H64

Pine H64 board has an AXP805 PMIC on it, wired up in standalone, or
self-working, mode.

Enable it in the device tree.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

arm64: dts: allwinner: h6: Add LED device nodes for Pine H64

The Pine H64 has 3 GPIO-controlled LEDs, which are labeled "heartbeat",
"link", and "status".

Add device nodes for them.

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

arm64: allwinner: h6: add PCF8563 RTC on Pine H64 board

Pine H64 board has a PCF8563 dedicated RTC connected to its R_I2C bus.

Enable the R_I2C bus and add the RTC to the device tree.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: allwinner: h6: add support for Pine H64 board

Pine H64 is an Allwinner H6-based SBC from Pine64, with the following
features:

- 1GiB/2GiB/4GiB LPDDR3 DRAM (in 4GiB situation only 3GiB is
accessible)
- AXP805 PMIC
- Raspberry-Pi-compatible GPIO header, "Euler" GPIO header (not
compatible with the "Euler" on Pine A64) and "Expansion" pin header
- 2 USB 2.0 ports and 1 USB 3.0 ports
- Audio jack
- MicroSD slot and eMMC module slot
- on-board SPI NOR flash
- 1Gbps Ethernet port (via RTL8211E PHY)
- HDMI port

Adds initial support for it, including the UART on the Expansion pin
header.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>