arm64: dts: allwinner: Use constants for RTC clock indexes

The binding header provides descriptive names for the RTC clock indexes,
since the indexes were arbitrarily chosen by the binding, not by the
hardware. Let's use the names, so the meaning is clearer.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220607012438.18183-2-samuel@sholland.org

arm64: dts: allwinner: h6: Use RSB for AXP805 PMIC connection

On boards where the only peripheral connected to PL0/PL1 is an X-Powers
PMIC, configure the connection to use the RSB bus rather than the I2C
bus. Compared to the I2C controller that shares the pins, the RSB
controller allows a higher bus frequency, and it is more CPU-efficient.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210103100007.32867-5-samuel@sholland.org

arm64: dts: allwinner: Use the new r_intc binding

The binding of R_INTC was updated to allow specifying interrupts other
than the external NMI, since routing those interrupts through the R_INTC
driver allows using them for wakeup.

Update the device trees to use the new binding.

Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

ARM: dts: sunxi: Fix the LED node names

According to the LED bindings, the LED node names are supposed to be led
plus an optional suffix. Let's fix our users to use that new scheme.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210114113538.1233933-6-maxime@cerno.tech

arm64: dts: allwinner: h6: Enable CPU opp tables for Orange Pi 3

Enable CPU opp tables for Orange Pi 3.

This needs to change the CPU regulator max voltage to fit
the OPP table.

Also add the ramp-delay information to avoid any out of spec
running as the regulator is slower at reaching the voltage
requested compare to the PLL reaching the frequency.

There is no such information for AXP805 but similar PMIC (AXP813)
has a DVM (Dynamic Voltage scaling Management) ramp rate equal
to 2500uV/us.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: h6: Move ext. oscillator to board DTs

It turns out that not all H6 boards have external 32kHz oscillator.
Currently the only one known such H6 board is Tanix TX6.

Move external oscillator node from common H6 dtsi to board specific dts
files where present.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: h6: orangepi-3: Add eMMC node

OrangePi 3 can optionally have 8 GiB eMMC (soldered on board). Because
those pins are dedicated to eMMC exclusively, node can be added for both
variants (with and without eMMC). Kernel will then scan bus for presence
of eMMC and act accordingly.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: unify header comment style

Allwinner device tree files used different comment style for
copyright notice.

Update this to keep a coherency.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwiner: Fix typo in dual licensed SPDX identifier

With dual licensed SPDX identifier the "OR" should
be uppercase.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: orange-pi-3: Enable IR receiver

Orange Pi 3 has an on-board IR receiver, enable it.

Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: orange-pi-3: Enable USB 3.0 host support

Enable Allwinner's USB 3.0 phy and the host controller. Orange Pi 3
board has GL3510 USB 3.0 4-port hub connected to the SoC's USB 3.0
port. All four ports are exposed via USB3-A connectors. VBUS is
always on, since it's powered directly from DCIN (VCC-5V) and
not switchable.

Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: Add mali GPU supply for H6 boards

Enable and add supply to the Mali GPU node on all the
H6 boards.

Regarding the datasheet the maximum time for supply to reach
its voltage is 32ms.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

arm64: dts: allwinner: orange-pi-3: Enable UART1 / Bluetooth

The board contains AP6256 WiFi/BT module that has its bluetooth part
connected to SoC's UART1 port. Enable this port, and add node for the
bluetooth device.

Bluetooth part is named bcm4345c5.

You'll need a BCM4345C5.hcd firmware file that can be found in the
Xulongs's repository for H6:

https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256

The driver expects the firmware at the following path relative to the
firmware directory:

brcm/BCM4345C5.hcd

Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>

arm64: dts: allwinner: orange-pi-3: Enable WiFi

Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is called
bcm43356 and can be used with the brcmfmac driver. The module is powered by
the two always on regulators (not AXP805).

WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be
configured so that it sets up an 1.8V input bias on this port. This is done
by the pio driver by reading the vcc-pg-supply voltage.

You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt
configuration that can be found in the Xulongs's repository for H6:

https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256

Mainline brcmfmac driver expects the firmware and nvram at the following
paths relative to the firmware directory:

brcm/brcmfmac43456-sdio.bin
brcm/brcmfmac43456-sdio.txt

Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: dts: allwinner: orange-pi-3: Enable HDMI output

Orange Pi 3 has a DDC_CEC_EN signal connected to PH2, that enables the DDC
I2C bus voltage shifter. Before EDID can be read, we need to pull PH2 high.
This is realized by the ddc-en-gpios property.

Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arm64: dts: allwinner: h6: Add Orange Pi 3 DTS

Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It
has the following features:

- Allwinner H6 quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB or 2GB LPDDR3 RAM
- AXP805 PMIC
- AP6256 Wifi/BT 5.0
- USB 2.0 host port (A)
- USB 2.0 micro usb, OTG
- USB 3.0 Host + 4 port USB hub (GL3510)
- Gigabit Ethernet (Realtek RTL8211E phy)
- HDMI 2.0 port
- soldered eMMC (optional)
- 3x LED (one is on the bottom)
- microphone
- audio jack
- PCIe

Add basic support for the board.

Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>