ARM: omap1: remove dead code

After the removal of the unused board files, I went through the
omap1 code to look for code that no longer has any callers
and remove that.

In particular, support for the omap7xx/omap8xx family is now
completely unused, so I'm only leaving omap15xx/omap16xx/omap59xx.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: linux-omap@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

ARM: omap: fix missing declaration warnings

Moving the plat-omap files triggered a sparse warning for omap1 and
omap2 that is now in a different file from before. Found some more sparse
warnings here that I address by making sure the declaration is visible
to both the caller and the callee, or they are static

mach-omap1/fb.c:33:17: warning: symbol 'omap_fb_resources' was not declared. Should it be static?
mach-omap1/timer32k.c:215:12: warning: symbol 'omap_init_clocksource_32k' was not declared. Should it be static?
mach-omap1/i2c.c:36:12: warning: symbol 'omap_i2c_add_bus' was not declared. Should it be static?
mach-omap1/i2c.c:115:12: warning: symbol 'omap_register_i2c_bus_cmdline' was not declared. Should it be static?
mach-omap1/i2c.c:140:12: warning: symbol 'omap_register_i2c_bus' was not declared. Should it be static?
mach-omap2/dma.c:180:34: warning: symbol 'dma_plat_info' was not declared. Should it be static?
mach-omap2/omap4-common.c:116:6: warning: symbol 'omap_interconnect_sync' was not declared. Should it be static?
mach-omap2/omap-iommu.c:113:5: warning: symbol 'omap_iommu_set_pwrdm_constraint' was not declared. Should it be static?

Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

ARM: omap1: move mach/*.h into mach directory

Most of the header files are no longer referenced from outside
arch/arm/mach-omap1, so move them all to that place directly
and change their users to use the new location.

The exceptions are:

- mach/compress.h is used by the core architecture code
- mach/serial.h is used by mach/compress.h

The mach/memory.h is empty and gets removed in the process,
avoiding the need for CONFIG_NEED_MACH_MEMORY_H.

Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 336

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 246 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.674189849@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: omap: move header to platform_data

This header only contains platform_data. Move it to the proper directory.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: Move plat/i2c.h into mach-omap1 folder

The current contents of plat/i2c.h are only relevant for OMAP1
platforms, as all the equivalent functions for OMAP2 has been
dropped in commit 65fa3e719f36 ("ARM: OMAP2+: Remove legacy i2c.c
platform init code"), and which has also moved the left-over code
from plat-omap into mach-omap1. The hwmod is a concept only
applicable for OMAP2 platforms, and the omap_i2c_reset() is
already declared in mach-omap2/i2c.h. So, move the current
plat/i2c.h header file into the mach-omap1 folder, and adjust
the header usage accordingly.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP2+: Remove legacy i2c.c platform init code

We can now initialize I2C for mach-omap2 using device tree. And we
can move the remaining code in plat-omap/i2c.c into mach-omap1/i2c.c.

Note that we cannot remove some of the I2C bus reset functions
as they are being used by hwmod code.

Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP1: Change interrupt numbering for sparse IRQ

Change interrupt numbering for sparse IRQ. We do this using
a fixed offset until we can drop irqs.h once all it's users
have been updated.

Note that this depends on the GPIO fix for the MPUIO IRQs
"gpio: omap: Fix regression for MPUIO interrupts".

Also note that this patch adds some extra irq alloc warnings
that will go away when we stop calling irq_alloc_descs
in gpio-omap.c with a follow-up patch.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: Fix i2c cmdline initcall for multiplatform

We only want this initcall to run when the kernel is
booted on omap SoCs. Fix the issue by initializing the
the initcall from separately for omap1 and omap2+.

This fixes the issue for omap2+ multiplatform configs
as we are using omap_subsys_initcall there.

Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: Fix relative includes for shared i2c.h file

As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:

http://www.spinics.net/lists/linux-omap/msg80520.html

To fix this for the shared i2c.h, let's re-introduce
a minimal plat/i2c.h.

Note that drivers must not use this header as it will
break build for omap2+ CONFIG_MULTIPLATFORM builds.

Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: Make plat-omap/i2c.c port checks local

The common code should not have any omap1 or omap2+
specific code, and should not need to call the cpu_is_omap
macros.

The only remaining user for cpu_is_omap macros is
omap_i2c_nr_ports(). Let's make those checks in
the omap specific implementation of omap_i2c_add_bus()
instead in order to remove cpu_is_omap usage from
the common code.

Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: Split plat/cpu.h into local soc.h for mach-omap1 and mach-omap2

We want to remove plat/cpu.h. To do this, let's first split
it to private soc.h to mach-omap1 and mach-omap2. We have to
keep plat/cpu.h around until the remaining drivers are fixed,
so let's include the local soc.h in plat/cpu.h and for drivers
still including plat/cpu.h.

Once the drivers are fixed not to include plat/cpu.h, we
can remove the file.

This is needed for the ARM common zImage support.

[tony@atomide.com: updated to not print a warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: Split plat-omap/i2c.c into mach-omap1 and mach-omap2

There's no need to keep the device related things in the
common i2c.c as omap2+ is using hwmod. Split the code to
mach-omap1 and mach-omap2 parts and only leave common
code to plat-omap/i2c.c.

Note that as omap1 only has one i2c controller, we can
now remove the old device related macros.

Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP1: Make plat/mux.h omap1 only

We are moving omap2+ to use the device tree based pinctrl-single.c
and will be removing the old mux framework. This will remove the
omap1 specific parts from plat-omap.

Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-pcmcia@lists.infradead.org
Cc: spi-devel-general@lists.sourceforge.net
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap: i2c: Fix muxing for command line enabled bus

The commit b63128e81214cc2db2995d690438055c26d213a5 broke the pin muxing
for I2C busses that are enabled from the kernel command line.

Fix this by defining the board registration function omap_register_i2c_bus
in common platform code as it was before but keep the muxing in architecture
dependent files.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap1: I2C mux and clocks for omap7xx

This change adds MUX pin configuration and clocks for I2C support
to OMAP 730 and 850-based devices.

Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap: Split i2c platform init for mach-omap1 and mach-omap2

Otherwise we cannot limit new mux code to mach-omap2.
The same signal names should eventually work for other
omaps under mach-omap2.

Note that these pins don't need to be OMAP_PIN_INPUT_PULLUP,
just OMAP_PIN_INPUT is enough.

Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>