ARM: omap1: remove dead code

After the removal of the unused board files, I went through the
omap1 code to look for code that no longer has any callers
and remove that.

In particular, support for the omap7xx/omap8xx family is now
completely unused, so I'm only leaving omap15xx/omap16xx/omap59xx.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: linux-omap@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

ARM: OMAP1: clock: Convert to CCF

OMAP1 still uses its own implementation of standard clock API defined in
include/linux/clk.h. Internals of that implementation are not visible
outside OMAP1 directory. As a consequence, device drivers are not able to
register clocks potentially provided by peripheral devices.

Drop OMAP1 implementation of the clock API and enable common clock
framework. Modify the remaining low level code to be compatible with
clock provider API and register the clocks with CCF.

Move initialisation of clocks to omap1_timer_init() to avoid memory
allocation issues at early setup phase from where omap1_init_early() is
called. Register the clocks after initialization of clock I/O registers,
local clock pointers used by OMAP1 clock ops, and local .rate fields of
clocks with no local implementation of .recalc ops, so CCF structures are
populated with correct data during clock registration. Instead of
enabling some of the registered clocks, flag them for CCF as critical.
Introduce .is_enabled op using code that verifies hardware status of clock
enablement, split out from implementation of .disable_unused op, so the
latter is actually called by CCF for not requested but hardware enabled
clocks. Add .round_rate ops where missing so .set_rate ops are called by
CCF as expected. Since CCF allows parallel execution of .enable/.disable
and .set_rate ops, protect registers shared among those groups of ops from
concurrent access with spinlocks. Drop local debugfs support in favor of
that provided by CCF.

v2: flag tc2_ck as CLK_IS_CRITICAL (Aaro)
v3: rebase on top of soc/omap1-multiplatform-5.18,
- drop no longer needed includes from arch/arm/mach-omap1/io.c

Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

ARM: OMAP1: fix typos in comments

Various spelling mistakes in comments.
Detected with the help of Coccinelle.

Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

ARM: OMAP1: clock: Remove noop code

There are some OMAP1 clock code bits that have no effect:
- crystal_type variable is set to 0 but never changed, then
crystal_type == 2 condition is never true and ck_ref.rate never set to
19200000,
- clk->ops->allow_idle() is called from omap_clk_enable_autoidle_all() but
that op is not configured for any clock, then the function does nothing
and the op field is not needed,
- ENABLE_ON_INIT flag is set for some clocks but is never checked by any
code, then not needed.
Drop that code.

Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

ARM: OMAP1: clock: Fix early UART rate issues

Commit ef772f2ee31e ("ARM: OMAP: Fix CONFIG_DEBUG_LL") was supposed to fix
low level debugging, most possibly by early enabling UART clocks. The fix
actually introduced early reset of most bits of MOD_CONF_CTRL_0 register,
with the exception of UART1 and UART2 clock related bits which were set
high. However, UART1 clock bit can play different roles on different
OMAP1 variants. On OMAP1610 it enables the clock as intended, but on
OMAP1510 it switches the clock rate from 12 to 48 MHz. Even worth, for
UART2 the bit changes its clock rate also on OMAP1610. As a result, UART
rates set by a bootloader can be unintentionally changed early on kernel
boot and low level debugging broken, not fixed. Besides, reset of all
other bits was not justified.

Don't touch register bits not related to UART clocks. Also, don't touch
the bit of UART2 clock. Make sure UART1 and UART3 are enabled early on
relevant OMAP1610 machine types while preserving bootloader UART clock
rates on others.

Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

ARM: omap1: move mach/*.h into mach directory

Most of the header files are no longer referenced from outside
arch/arm/mach-omap1, so move them all to that place directly
and change their users to use the new location.

The exceptions are:

- mach/compress.h is used by the core architecture code
- mach/serial.h is used by mach/compress.h

The mach/memory.h is empty and gets removed in the process,
avoiding the need for CONFIG_NEED_MACH_MEMORY_H.

Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

ARM: omap1: move mach/usb.h to include/linux/soc

The register definitions in this header are used in at least four
different places, with little hope of completely cleaning that up.

Split up the file into a portion that becomes a linux-wide header
under include/linux/soc/ti/, and the parts that are actually only
needed by board files.

Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500

Based on 2 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: OMAP1: fix USB host on 1710

There is a long-standing bug that OHCI USB host controller does
not respond on 1710, because of wrong clock definitions. See e.g.
http://marc.info/?l=linux-omap&m=119634441229321&w=2. All register reads
return just zeroes:

[ 1.896606] ohci ohci: OMAP OHCI
[ 1.912597] ohci ohci: new USB bus registered, assigned bus number 1
[ 1.933776] ohci ohci: irq 38, io mem 0xfffba000
[ 2.012573] ohci ohci: init err (00000000 0000)
[ 2.030334] ohci ohci: can't start
[ 2.046661] ohci ohci: startup error -75
[ 2.063201] ohci ohci: USB bus 1 deregistered

After some experiments, it seems that when changing the usb_dc_ck /
SOFT_REQ enable bit from USB_REQ_EN_SHIFT to SOFT_USB_OTG_DPLL_REQ_SHIFT
(like done also on 7XX), the USB appears to work:

[ 2.183959] ohci ohci: OMAP OHCI
[ 2.198242] ohci ohci: new USB bus registered, assigned bus number 1
[ 2.215820] ohci ohci: irq 38, io mem 0xfffba000
[ 2.324798] hub 1-0:1.0: USB hub found
[ 2.361267] hub 1-0:1.0: 3 ports detected

The patch is tested on Nokia 770.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

ARM: OMAP: Split sram.h to local headers and minimal shared header

Most of the defines are specific to omap1 and omap2+,
and should be in the local headers. Only minimal function
prototypes need to be shared.

As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:

http://www.spinics.net/lists/linux-omap/msg80520.html

So this patch re-adds a minimal plat/sram.h.

The new plat/sram.h must not be included from drivers,
that will break build for omap2+ CONFIG_MULTIPLATFORM.

Note that this patch temporarily adds two more
relative includes; Those will be removed in the
following patch.

Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: Split plat/cpu.h into local soc.h for mach-omap1 and mach-omap2

We want to remove plat/cpu.h. To do this, let's first split
it to private soc.h to mach-omap1 and mach-omap2. We have to
keep plat/cpu.h around until the remaining drivers are fixed,
so let's include the local soc.h in plat/cpu.h and for drivers
still including plat/cpu.h.

Once the drivers are fixed not to include plat/cpu.h, we
can remove the file.

This is needed for the ARM common zImage support.

[tony@atomide.com: updated to not print a warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: clock: split plat/clkdev_omap.h into OMAP1/2 files

To facilitate the ARM single image work, split
arch/arm/plat-omap/include/plat/clkdev_omap.h into the
arch/arm/mach-omap1/clock.h and arch/arm/mach-omap2/clock.h files.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: remove plat/clock.h

Remove arch/arm/plat-omap/include/plat/clock.h by merging it into
arch/arm/mach-omap1/clock.h and arch/arm/mach-omap2/clock.h.
The goal here is to facilitate ARM single image kernels by removing
includes via the "plat/" symlink.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: fixed to remove duplicate clock.h includes]
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: duplicate plat-omap/clock.c into mach-omap[12]/clock.c

Duplicate arch/arm/plat-omap/clock.c into arch/arm/mach-omap1/clock.c
and arch/arm/mach-omap2/clock.c. This is to support people who are working
on the ARM single image kernel and the OMAP common clock framework
conversion.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: Make plat/sram.h local to plat-omap

We can move this from plat to be local to plat-omap
for common ARM zImage support.

Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: unwrap strings

Find and unwrap wrapped strings in the style:

pr_debug("clockdomain: hardware cannot set/clear wake up of "
"%s when %s wakes up\n", clkdm1->name, clkdm2->name);

Keeping these strings contiguous seems to be the current Linux kernel
policy.

The offending lines were found with the following command:

pcregrep -rnM '"\s*$\s*"' arch/arm/*omap*

While here, some messages have been clarified, some pr_warning(
... calls have been converted to pr_warn( ..., and some printk(KERN_*
... have been converted to pr_*.

Signed-off-by: Paul Walmsley <paul@pwsan.com>

ARM: OMAP1: remove the crystal type tag parsing

The omap1 crystal setting uses the OMAP custom tags.
Those tags are not used in upstream kernel and therefore the crystal
type is never set by the tag parsing code on upstream kernels.
Remove the crystal tag parsing code.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: Make FS USB omap1 only

As the FS USB code is not being actively used for omap2+
there's no point keeping it around for omap2+.

Let's make the FS USB platform init code omap1 only so
we can remove the last user of omap_read/write for omap2+,
and simplify things for further USB, DMA, and device tree
related work.

While at it, also group the mach includes for the related
drivers.

Cc: linux-usb@vger.kernel.org
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: Remove plat/io.h by splitting it into mach/io.h and mach/hardware.h

This is needed to minimize io.h so the SoC specific io.h
for ARMs can removed.

Note that minimal driver changes for DSS and RNG are needed to
include cpu.h for SoC detection macros.

Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP1: Move most of plat/io.h into local iomap.h

There's no need to have these in plat/io.h.

While at it, clean up the includes to group them
like they typically are grouped.

Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP1: Always reprogram dpll1 rate at boot

DPLL1 reprogramming to a different rate is actually blocked inside
omap1_select_table_rate(). However, it is already forced at boot, for
boards which boot at unusable clock rates, and this seems to work
correctly.

OTOH, we now have a fine, run time performed clock selection algorithm
implemented, which prevents less powerfull SoCs from being overclocked
unintentionally.

Allow reprogramming of dpll1 by default, and use it for switching to the
higest supported clock rate with all boards, including those already
booting at a usable rate of 60 MHz or above.

Created against linux-omap/master tip as of Thu Dec 1,
commit f83c2a8cbb59981722d1ab610c79adfd034a2667. Requires the just
submitted patch "ARM: OMAP1: Move dpll1 rates selection from config to
runtime" to prevent from unintentional overclocking. Tested on Amstrad
Delta.

Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP1: Update dpll1 default rate reprogramming method

According to comments in omap1_select_table_rate(), reprogramming dpll1
is tricky, and should always be done from SRAM.

While being at it, move OMAP730 special case handling inside
omap_sram_reprogram_clock().

Created on top of version 2 of the series "ARM: OMAP1: Fix dpll1
reprogramming related issues", which it depends on.
Tested on Amstrad Delta.

Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP1: Move dpll1 rates selection from config to runtime

For still better multi-OMAP1 support, expand omap1_rate_table with flags
for different SoC types and match them while selecting clock rates. The
idea is stolen from current omap24xx clock rate selection algorithm.

Since clkdev platform flag definitions are reused here, those had to be
expanded with one extra entry for OMAP1710 subtype, as this is the only
SoC for which we allow selection of the highest, 216 MHz rate.

Once done, remove no longer needed clock rate configure time options.

Tested on Amstrad Delta.

Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP1: recalculate loops per jiffy after dpll1 reprogram

Otherwise timing is inaccurate, resulting in devices which depend on it,
like omap-keypad, broken.

Tested on Amstrad Delta.

Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: removed comment referencing a development branch]
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP1: Fix ckctl value used for dpll1 defualt rate

Use the exact value found in omap1_rate_table, otherwise I have been
experiencing issues with correct timekeeping on my Amstrad Delta.

Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: removed comment referencing a development branch]
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP1: Fix reprogramming of DPLL1 for systems that boot at rates below 60MHz

Commit e9b7086b80c4d9e354f4edc9e280ae85a60df408 (ARM: OMAP: Fix
reprogramming of dpll1 rate) fixed a regression for systems that
did not rely on bootloader set rates.

However, it also introduced a new problem where the rates selected
in .config would not take affect as omap1_select_table_rate
currently refuses to reprogram DPLL1 if it's already initialized.

This was not a problem earlier, as the reprogramming was done
earlier with ck_dpll1_p->rate uninitialized.

Fix this by forcing the reprogramming on systems booting at rates
below 60MHz. Note that the long term fix is to make the rates
SoC specific later on.

Thanks for Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for figuring
this one out.

Reported-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP: Fix reprogramming of dpll1 rate

Commit a66cb3454f220f49f900646ebdc76cb943319eb7 (ARM: OMAP: Map SRAM
later on with ioremap_exec()) moved the SRAM init to happen later
to remove a dependency to early SoC detection for map_io.

This broke booting on some boards not using Kconfig option for
OMAP_CLOCKS_SET_BY_BOOTLOADER as the dpll1 reprogramming would
cause the following error:

kernel BUG at arch/arm/plat-omap/sram.c:226!
Internal error: Oops - undefined instruction: 0 [#1] PREEMPT
Modules linked in:

CPU: 0 Not tainted (3.2.0-rc1-e3 #9)
PC is at omap_sram_reprogram_clock+0x28/0x30
LR is at omap1_select_table_rate+0x88/0xb4
pc : [<c001b0c4>] lr : [<c0019f54>] psr: 600000d3
sp : c035bf10 ip : c035bf20 fp : c035bf1c
r10: c035bfd4 r9 : 54029252 r8 : c03f8120
r7 : c0362b50 r6 : 00b71b00 r5 : c03873cc r4 : c0362b40
r3 : 00000000 r2 : c0362b40 r1 : 0000010a r0 : 00002cb0
Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel
Control: 0000317f Table: 10004000 DAC: 00000017
Process swapper (pid: 0, stack limit = 0xc035a270)
Stack: (0xc035bf10 to 0xc035c000)
bf00: c035bf3c c035bf20 c0019f54 c001b0ac
bf20: 00001000 00002cb3 00000004 c035ed4c c035bf74 c035bf40 c033ea24 c0019edc
bf40: c02f526c 00000002 00000015 bc058c9b 93111a16 c035335c 02000000 c035ed4c
bf60: c035ed4c c03f8120 c035bf84 c035bf78 c00194c4 c033e8ec c035bfc4 c035bf88
bf80: c033bc24 c00194a0 c035bf90 c035bf98 00000000 00000000 00000000 00000000
bfa0: 00000001 00000000 c0354678 c035ece4 10004000 103532f4 c035bff4 c035bfc8
bfc0: c0338574 c033b598 00000000 00000000 00000000 c035467c 0000317d c035c03c
bfe0: c0354678 c035ece4 00000000 c035bff8 10008040 c0338508 00000000 00000000
Backtrace:
[<c001b09c>] (omap_sram_reprogram_clock+0x0/0x30) from [<c0019f54>] (omap1_select_table_rate+0x88/0xb4)
[<c0019ecc>] (omap1_select_table_rate+0x0/0xb4) from [<c033ea24>] (omap1_clk_init+0x148/0x334)
r7:c035ed4c r6:00000004 r5:00002cb3 r4:00001000
[<c033e8dc>] (omap1_clk_init+0x0/0x334) from [<c00194c4>] (omap1_init_early+0x34/0x48)
r8:c03f8120 r7:c035ed4c r6:c035ed4c r5:02000000 r4:c035335c
[<c0019490>] (omap1_init_early+0x0/0x48) from [<c033bc24>] (setup_arch+0x69c/0x79c)
[<c033b588>] (setup_arch+0x0/0x79c) from [<c0338574>] (start_kernel+0x7c/0x2f4)
[<c03384f8>] (start_kernel+0x0/0x2f4) from [<10008040>] (0x10008040)
r7:c035ece4 r6:c0354678 r5:c035c03c r4:0000317d
Code: 0a000002 e1a0e00f e12fff13 e89da800 (e7f001f2)

Fix this by adding omap1_clk_late_init() that only reprograms dpll1
if the bootloader rate is less than 60MHz. This also allows removing
of the OMAP_CLOCKS_SET_BY_BOOTLOADER option.

Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP1: clock_data: use runtime cpu / machine checks

Otherwise multi-omap1 configurations may set wrong clock speed.

Created and tested against l-o master on Amstrad Delta.

Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

I2C: i2c-omap: Change device name: i2c_omap -> omap_i2c

The convention for omap device naming is omap_XXX.

Rename the device and driver name in order to stick
to this naming convention.

Change device name in clock nodes as well.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP: GPIO: Implement GPIO as a platform device

Implement GPIO as a platform device.

GPIO APIs are used in machine_init functions. Hence it is
required to complete GPIO probe before board_init. Therefore
GPIO device register and driver register are implemented as
postcore_initcalls.

omap_gpio_init() does nothing now and this function would be
removed in the next patch as it's usage is spread across most
of the board files.

Inorder to convert GPIO as platform device, modifications are
required in clockxxxx_data.c file for OMAP1 so that device names
can be used to obtain clock instead of getting clocks by
name/NULL ptr.

Use runtime pm APIs (pm_runtime_put*/pm_runtime_get*) for enabling
or disabling the clocks, modify sysconfig settings and remove usage
of clock FW APIs.
Note 1: Converting GPIO driver to use runtime PM APIs is not done as a
separate patch because GPIO clock names are different for various OMAPs
and are different for some of the banks in the same CPU. This would need
usage of cpu_is checks and bank id checks while using clock FW APIs in
the gpio driver. Hence while making GPIO a platform driver framework,
PM runtime APIs are used directly.

Note 2: While implementing GPIO as a platform device, pm runtime APIs
are used as mentioned above and modification is not done in gpio's
prepare for idle/ resume after idle functions. This would be done
in the next patch series and GPIO driver would be made to use dev_pm_ops
instead of sysdev_class in that series only.

Due to the above, the GPIO driver implicitly relies on
CM_AUTOIDLE = 1 on its iclk for power management to work, since the
driver never disables its iclk.
This would be taken care in the next patch series (see Note 3 below).

Refer to
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg39112.html
for more details.

Note 3: only pm_runtime_get_sync is called in gpio's probe() and
pm_runtime_put* is never called. This is to make the implementation
similar to the existing GPIO code. Another patch series would be sent
to correct this.

In OMAP3 and OMAP4 gpio's debounce clocks are optional clocks. They
are enabled/ disabled whenever required using clock framework APIs

TODO:
1. Cleanup the GPIO driver. Use function pointers and register
offest pointers instead of using hardcoded values
2. Remove all cpu_is_ checks and OMAP specific macros
3. Remove usage of gpio_bank array so that only
instance specific information is used in driver code
4. Rename 'method'/ avoid it's usage
5. Fix the non-wakeup gpios handling for OMAP2430, OMAP3 & OMAP4
6. Modify gpio's prepare for idle/ resume after idle functions
to use runtime pm implentation.

Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Basak, Partha <p-basak2@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated for bank specific revision and updated boards]
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap1: omap7xx clocks, mux, serial fixes

This change adds in the necessary clocks and mux pins for UART
control on omap7xx devices. I also made a change in the serial
code to only try and initialize two UARTs in omap_serial_init, as
these devices don't have three.

Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP1: clock: some cleanup

Convert most of the magic numbers in mach-omap1/clock_data.c to use
macros. Clean up a few comments to conform with Documentation/CodingStyle.
Mark the current clkops_uart as being OMAP16xx-only, and add some comments
to indicate that it does not belong there, for future cleanup.

This patch should not cause any functional changes.

Signed-off-by: Paul Walmsley <paul@pwsan.com>

OMAP4: clock: Add dummy clock nodes for interface clocks

On OMAP4 platform the iclk control is completly under hardware control
and no software control is available.

This difference w.r.t previous OMAP's needs all the common driver
accross OMAP's , cpu_is_xxxx() checks. To avoid poulluting the
drivers dummy clock nodes are created (The autogeneration
script has been updated accordingly).

Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: made OMAP1 dummy_ck common and edited patch to reuse that]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

OMAP clock: drop RATE_FIXED clock flag

The RATE_FIXED clock flag is pointless. In the OMAP1 clock code, it
simply causes the omap1_clk_round_rate() function to return the
current rate of the clock. omap1_clk_round_rate(), however, should
never be called for a fixed-rate clock, since none of these clocks
have a .round_rate function pointer set in their struct clk records.
Similarly, in the OMAP2+ clock code, the RATE_FIXED flag just causes
the clock code to emit a warning if the OMAP clock maintainer was
foolish enough to add a .round_rate function pointer to a fixed-rate
clock. "Doctor, it hurts when I pretend that a fixed-rate clock is
rate-changeable." "Then don't pretend that a fixed-rate clock is
rate-changeable." It has no functional value. This patch drops the
RATE_FIXED clock flag, removing it from all clocks that are so marked.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>

OMAP clock: drop .id field; ensure each clock has a unique name

After the clkdev conversion, the struct clk.id field became
superfluous, so, drop it. Bring the clock names closer to the TRMs
and ensure they are unique for debugfs.

Signed-off-by: Paul Walmsley <paul@pwsan.com>

OMAP1 clock: convert armwdt_ck to use the fixed divisor recalc function

The armwdt_ck clock uses a fixed divisor, so it can use the OMAP clock
fixed divisor recalculation code, rather than a custom function.

Signed-off-by: Paul Walmsley <paul@pwsan.com>

OMAP1 clock: remove __initdata from struct clk_functions to prevent crash

Commit 52650505fbf3a6ab851c801f54e73e76c55ab8da added an __initdata
decoration to the structure containing the clk_enable and clk_disable
functions. Once init data was freed, these pointers went to null, and
the next enable or disable call caused the kernel to crash. This
change removes this decoration.

Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
[paul@pwsan.com: patch manually split and commit message edited]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

OMAP1 clock: Add missing clocks for OMAP 7xx

This change adds in some missing clocks that were needed as a result
of 526505... (OMAP1 clock: convert mach-omap1/clock.h to
mach-omap1/clock_data.c). Prior to this, it was just assumed that
these clocks existed for all devices, and it was used directly instead
of calling it out with a clock_get call or similar. So, not having
the CK_7XX meant these clocks weren't being used anymore for omap 7xx
devices, which broke things badly.

Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
[paul@pwsan.com: commit message edited]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

omap1: Add 7xx clocks and pin muxes for SPI

Commit 35c9049b27040d09461bc90928ad770be7ddf661 added
drivers/spi/omap_spi_100k.c.

This patch add the related clocks and pin muxing
entries to make the driver work on omap7xx platforms.

Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap1: I2C mux and clocks for omap7xx

This change adds MUX pin configuration and clocks for I2C support
to OMAP 730 and 850-based devices.

Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP1 clock: convert mach-omap1/clock.h to mach-omap1/clock_data.c

The OMAP1 clock code currently #includes a large .h file full of static
data structures. Instead, define the data in a .c file.

Russell King <linux@arm.linux.org.uk> proposed this new arrangement:

http://marc.info/?l=linux-omap&m=125967425908895&w=2

This patch also deals with most of the flagrant checkpatch violations.

While here, separate the mpu_rate data structures out into their own
files, opp.h and opp_data.c. In the long run, these mpu_rate tables
should be replaced with OPP code.

Also includes a patch from Felipe Balbi <felipe.balbi@nokia.com> to
mark omap1_clk_functions as __initdata to avoid a section warning:

http://patchwork.kernel.org/patch/64366/

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Nishanth Menon <nm@ti.com>