treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 174

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 655 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: signal handling support for FDPIC_FUNCPTRS functions

Signal handlers are not direct function pointers but pointers to function
descriptor in that case. Therefore we must retrieve the actual function
address and load the GOT value into r9 from the descriptor before branching
to the actual handler.

If a restorer is provided, we also have to load its address and GOT from
its descriptor. That descriptor address and the code to load it is pushed
onto the stack to be executed as soon as the signal handler returns.

However, to be compatible with NX stacks, the FDPIC bounce code is also
copied to the signal page along with the other code stubs. Therefore this
code must get at the descriptor address whether it executes from the stack
or the signal page. To do so we use the stack pointer which points at the
signal stack frame where the descriptor address was stored. Because the
rt signal frame is different from the simpler frame, two versions of the
bounce code are needed, and two variants (ARM and Thumb) as well. The
asm-offsets facility is used to determine the actual offset in the signal
frame for each version, meaning that struct sigframe and rt_sigframe had
to be moved to a separate file.

Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mickael GUENE <mickael.guene@st.com>
Tested-by: Vincent Abriou <vincent.abriou@st.com>
Tested-by: Andras Szemzo <szemzo.andras@gmail.com>

ARM: 7895/1: signal: fix armv7-m build issue in sigreturn_codes.S

After "ARM: signal: sigreturn_codes should be endian neutral to
work in BE8" commit, thumb only platforms, like armv7m, fails to
compile sigreturn_codes.S. The reason is that for such arch
values '.arm' directive and arm opcodes are not allowed.

Fix conditionally enables arm opcodes only if no CONFIG_CPU_THUMBONLY
defined and it uses .org instructions to keep sigreturn_codes
layout.

Suggested-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

ARM: signal: sigreturn_codes should be endian neutral to work in BE8

In case of BE8 kernel data is in BE order whereas code stays in LE
order. Move sigreturn_codes to separate .S file and use proper
assembler mnemonics for these code snippets. In this case compiler
will take care of proper instructions byteswaps for BE8 case.
Change assumes that sufficiently Thumb-capable tools are used to
build kernel.

Problem was discovered during ltp testing of BE system: all rt_sig*
tests failed. Tested against the same tests in both BE and LE modes.

Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>