[astro][hid] Goodix touch driver

TEST: test on astro with hidtouch
Change-Id: I780befb0ffdf83680af7124f0bb6adb33f6f5cf1

[gpio] Refactor the GPIO protocol

This is a first step in a move toward using protocols to represent
individual resources. A similar change will be made to the I2C protocol
to bring it in line with how I2C is used on x86 platforms.

From the client's point of view, an instance of the ZX_PROTOCOL_GPIO
protocol now represents a single pin. The protocol remains the same,
except the "uint32_t index" has been removed from all the protocol functions.

For devices that have only one GPIO resource assigned to them, the driver
can simply call device_get_protocol() to access the GPIO protocol for the pin.
To for devices with more than one GPIO pins, a new API in the platform bus called
pdev_get_protocol() must be used instead.

In addition, we add a new protocol ZX_PROTOCOL_GPIO_IMPL, which is now
implemented by the GPIO drivers. This protocol is essentially the same as
the old GPIO protocol, except "index" has been renamed "pin".
Board drivers may use this protocol directly when doing low level system
configuration, specifying pin numbers directly.

TEST: Booted on VIM2 and Hikey.
On VIM2, USB, display, ethernet and the GPIO test driver are working properly
On Hikey, the system boots and USB is functional.

Change-Id: I44f1bc11ad9793543361a2d19d7a2de4458c334b

[ddk][gpio] Break gpio_config() API into two functions

gpio_config_in() is used to configure a pin for input, while
gpio_config_out() is used to configure a pin for output.
gpio_config_out() now takes an initial value for the pin,
so the configuration and value can be set atomically to avoid a
race condition or glitch between setting it as output and writing the value.

Also removed some unnecessary GPIO configuration flags.
Now we only have flags for configuring the pull-up in gpio_config_in().
gpio_get_interrupt() uses interrupt handle flags for configuring edge vs level triggered,
so we don't need GPIO_* flags for these.

TEST: manual testing on VIM2, astro and gauss

ZX-2564 #in progress
ZX-2465 #in progress

Change-Id: I280c489ba951ca5953c0a2d57135c3482dd96c37

[dev][platform-bus] Clean-up and simplify platform bus protocol:

- Remove "flags" parameter from pbus_device_add().
Now platform devices can only be started in new devhosts.

- Add new API pbus_protocol_device_add(), for binding drivers that implement
platform bus protocols like GPIO and I2C_IMPL.
pbus_protocol_device_add() is equivalent to pbus_device_add(PDEV_ADD_PBUS_DEVHOST)
followed by pbus_wait_protocol().

- Remove pbus_wait_protocol(). pbus_protocol_device_add() does the wait for you automatically.

- Rename pbus_set_protocol() to pbus_register_protocol()

These changes will hopefully make the platform bus protocol easier
to understand and use.
I found two places where people accidentally using PDEV_ADD_PBUS_DEVHOST
inappropriately (probably copy & paste errors), which resulted in
the entire network stack and storage stack running in the platform bus devhost.
Hopefully this change will make it impossible for mistakes like that to happen again.

While doing this I also noticed that the gauss nand driver and vim2 ethernet driver
were running in the platform bus devhost. This change fixes that.

Also removed some remnants of the pbus_device_enable() API, which has been removed previously.

TEST: boot up on qemu, VIM2, gauss and astro and verified platform devices all start up properly

Change-Id: I580269bc6f53a63348ba8ab580259b1ba56dd393

[amlogic][gpu] Refactoring GPU driver

Change-Id: Ic04890b638912982e780b1141c301adf57548fbe

[astro][touch] ft3x27 driver

Change-Id: I2958fdef9e2a8b0a4b641dd5078d2fb6e60d1843