sys: Remove $FreeBSD$: two-line .h pattern

Remove /^\s*\*\n \*\s+\$FreeBSD\$$\n/

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.

Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix

Remove dead code.

is_physical_memory() dead since 235a54de.

Reviewed by: markj
Differential revision: https://reviews.freebsd.org/D35056
MFC after: 2 weeks

Simplify swi for bus_dma.

When a DMA request using bounce pages completes, a swi is triggered to
schedule pending DMA requests using the just-freed bounce pages. For
a long time this bus_dma swi has been tied to a "virtual memory" swi
(swi_vm). However, all of the swi_vm implementations are the same and
consist of checking a flag (busdma_swi_pending) which is always true
and if set calling busdma_swi. I suspect this dates back to the
pre-SMPng days and that the intention was for swi_vm to serve as a
mux. However, in the current scheme there's no need for the mux.

Instead, remove swi_vm and vm_ih. Each bus_dma implementation that
uses bounce pages is responsible for creating its own swi (busdma_ih)
which it now schedules directly. This swi invokes busdma_swi directly
removing the need for busdma_swi_pending.

One consequence is that the swi now works on RISC-V which had previously
failed to invoke busdma_swi from swi_vm.

Reviewed by: imp, kib
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D33447

minidump: Parameterize minidumpsys()

The minidump code is written assuming that certain global state will not
change, and rightly so, since it executes from a kernel debugger
context. In order to support taking minidumps of a live system, we
should allow copies of relevant global state that is likely to change to
be passed as parameters to the minidumpsys() function.

This patch does the work of parameterizing this function, by adding a
struct minidumpstate argument. For now, this struct allows for copies of
the kernel message buffer, and the bitset that tracks which pages should
be dumped (vm_page_dump). Follow-up changes will actually make use of
these arguments.

Notably, dump_avail[] does not need a snapshot, since it is not expected
to change after system initialization.

The existing minidumpsys() definitions are renamed, and a thin MI
wrapper is added to kern_dump.c, which handles the construction of
the state struct. Thus, calling minidumpsys() remains as simple as
before.

Reviewed by: kib, markj, jhb
Sponsored by: Juniper Networks, Inc.
Sponsored by: Klara, Inc.
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D31989

minidump: De-duplicate is_dumpable()

The function is identical in each minidump implementation, so move it to
vm_phys.c. The only slight exception is powerpc where the function was
public, for use in moea64_scan_pmap().

Reviewed by: kib, markj, imp (earlier version)
MFC after: 2 weeks
Sponsored by: Juniper Networks, Inc.
Sponsored by: Klara, Inc.
Differential Revision: https://reviews.freebsd.org/D31884

Move vm_page_dump bitset array definition to MI code

These definitions were repeated by all architectures, with small
variations. Consolidate the common definitons in machine
independent code and use bitset(9) macros for manipulation. Many
opportunities for deduplication remain in the machine dependent
minidump logic. The only intended functional change is increasing
the bit index type to vm_pindex_t, allowing the indexing of pages
with address of 8 TiB and greater.

Reviewed by: kib, markj
Approved by: scottl (implicit)
MFC after: 1 week
Sponsored by: Ampere Computing, Inc.
Differential Revision: https://reviews.freebsd.org/D26129

[PPC64] Initial kernel minidump implementation

Based on POWER9BSD implementation, with all POWER9 specific code removed and
addition of new methods in PPC64 MMU interface, to isolate platform specific
code. Currently, the new methods are implemented on pseries and PowerNV
(D21643).

Reviewed by: jhibbits
Differential Revision: https://reviews.freebsd.org/D21551

Break out the cpu_features setup to its own function, to be run earlier

The new POWER9 MMU configuration is slightly different from current setups.
Rather than special-casing on POWER9, move the initialization of cpu_features
and cpu_features2 to as early as possible, so that platform and MMU
configuration can be based upon CPU features instead of specific CPUs if at all
possible.

Reviewed by: nwhitehorn

sys/powerpc: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.

Provide support for userland binaries using the new ELFv2 ABI. This is a
new, simplified, ELF ABI that avoids some of the stranger aspects of the
existing 64-bit PowerPC ABI (function descriptors, in particular). Actually
generating such executables requires a new version of binutils and a newer
compiler (either GCC or clang) than GCC 4.2.1.

A new jail(8) with a configuration file, to replace the work currently done
by /etc/rc.d/jail.

Update PowerPC event timer code to use new event timers infrastructure.

Reviewed by: nwitehorn
Tested by: andreast
H/W donated by: Gheorghe Ardelean

MFppc64:

Kernel sources for 64-bit PowerPC, along with build-system changes to keep
32-bit kernels compiling (build system changes for 64-bit kernels are
coming later). Existing 32-bit PowerPC kernel configurations must be
updated after this change to specify their architecture.

MFC r199886:

Add a CPU features framework on PowerPC and simplify CPU setup a little
more. This provides three new sysctls to user space:
hw.cpu_features - A bitmask of available CPU features
hw.floatingpoint - Whether or not there is hardware FP support
hw.altivec - Whether or not Altivec is available

PR: powerpc/139154

Add a CPU features framework on PowerPC and simplify CPU setup a little
more. This provides three new sysctls to user space:
hw.cpu_features - A bitmask of available CPU features
hw.floatingpoint - Whether or not there is hardware FP support
hw.altivec - Whether or not Altivec is available

PR: powerpc/139154
MFC after: 10 days

PowerPC common SMP startup and time base rework.

- make mftb() shared, rewrite in C, provide complementary mttb()
- adjust SMP startup per the above, additional comments, minor naming
changes
- eliminate redundant TB defines, other minor cosmetics

Reviewed by: marcel, nwhitehorn
Obtained from: Freescale, Semihalf

Factor out platform dependent things unrelated to device drivers into a
new platform module. These are probed in early boot, and have the
responsibility of determining the layout of physical memory, determining
the CPU timebase frequency, and handling the zoo of SMP mechanisms
found on PowerPC.

Reviewed by: marcel, raj
Book-E parts by: raj

Add support for 64-bit PowerPC CPUs operating in the 64-bit bridge mode
provided, for example, on the PowerPC 970 (G5), as well as on related CPUs
like the POWER3 and POWER4.

This also adds support for various built-in hardware found on Apple G5
hardware (e.g. the IBM CPC925 northbridge).

Reviewed by: grehan

- Import the HEAD csup code which is the basis for the cvsmode work.

Allow the cacheline size on PowerPC to be set at runtime. This is essential for
supporting 64-bit CPUs, which often have 128-byte cache lines instead of the
standard 32.

For AIM, have cpu_idle() set MSR_POW when the powerpc_pow_enabled
variable is set. On my Mac Mini this puts the CPU in NAP mode when
the kernel is idle and, any technical or environmental reasons
aside, avoids that I have to listen to the fan all day :-)

Initial support for Freescale PowerQUICC III MPC85xx system-on-chip family.

The PQ3 is a high performance integrated communications processing system
based on the e500 core, which is an embedded RISC processor that implements
the 32-bit Book E definition of the PowerPC architecture. For details refer
to: http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MPC8555E

This port was tested and successfully run on the following members of the PQ3
family: MPC8533, MPC8541, MPC8548, MPC8555.

The following major integrated peripherals are supported:

* On-chip peripherals bus
* OpenPIC interrupt controller
* UART
* Ethernet (TSEC)
* Host/PCI bridge
* QUICC engine (SCC functionality)

This commit brings the main functionality and will be followed by individual
drivers that are logically separate from this base.

Approved by: cognet (mentor)
Obtained from: Juniper, Semihalf
MFp4: e500

Split decr_init() into two, with the section that reads the timebase
frequency from OpenFirmware moved out and into a routine that is called
from cpu_startup().

This allows correct reporting of the CPU clockspeed when printing out
CPU information at boot time.

Reported by: numerous
Reviewed by: marcel
MFC after: 1 day

Revamp the interrupt handling in support of INTR_FILTER. This includes:
o Revamp the PIC I/F to only abstract the PIC hardware. The
resource handling has been moved to nexus, where it belongs.
o Include EOI and MASK+EOI methods to the PIC I/F in support of
INTR_FILTER.
o With the allocation of interrupt resources and setup of
interrupt handlers in the common platform code we can delay
talking to the PIC hardware after enumeration of all devices.
Introduce a call to powerpc_intr_enable() in configure_final()
to achieve that and have powerpc_setup_intr() only program the
PIC when !cold.
o As a consequence of the above, remove all early_attach() glue
from the OpenPIC and Heathrow PIC drivers and have them
register themselves when they're found during enumeration.
o Decouple the interrupt vector from the interrupt request line.
Allocate vectors increasingly so that they can be used for
the intrcnt index as well. Extend the Heathrow PIC driver to
translate between IRQ and vector. The OpenPIC driver already
has the support for vectors in hardware.

Approved by: re (blanket)

Add kdb_cpu_sync_icache(), intended to synchronize instruction
caches with data caches after writing to memory. This typically
is required to make breakpoints work on ia64 and powerpc. For
those architectures the function is implemented.

o Move the prototype of mem_valid() from ofw_machdep.h to md_var.h.
This avoids that mem.c has to include ofw_machdep.h, including
all OFW related headers.
o Provide a stub for OF_decode_addr(), which is used by low-level
console drivers to obtain a tag and handle given a OFW phandle.
This is different from sparc64, where a fake bus tag needs to be
created explicitly.

Further cleanup <machine/cpu.h> and <machine/md_var.h>: move the MI
prototypes of cpu_halt(), cpu_reset() and swi_vm() from md_var.h to
cpu.h. This affects db_command.c and kern_shutdown.c.

ia64: move all MD prototypes from cpu.h to md_var.h. This affects
madt.c, interrupt.c and mp_machdep.c. Remove is_physical_memory().
It's not used (vm_machdep.c).

alpha: the MD prototypes have been left in cpu.h with a comment
that they should be there. Moving them is left for later. It was
expected that the impact would be significant enough to be done in
a seperate commit.

powerpc: MD prototypes left in cpu.h. Comment added.

Suggested by: bde
Tested with: make universe (pc98 incomplete)

Export the ns_per_tick variable through md_var.h rather than by declaring
it extern in cpu.c.

Add cpu.c. This contains one exported function, cpu_setup(), which handles
setup of and printing information about cpus.

Obtained from: NetBSD (parts)

- Rename the "powerpc" timecounter to the "decrementer" timecounter.
- Initialise it earlier.

Change hw.physmem and hw.usermem to unsigned long like they used to be
in the original hardwired sysctl implementation.

The buf size calculator still overflows an integer on machines with large
KVA (eg: ia64) where the number of pages does not fit into an int. Use
'long' there.

Change Maxmem and physmem and related variables to 'long', mostly for
completeness. Machines are not likely to overflow 'int' pages in the
near term, but then again, 640K ought to be enough for anybody. This
comes for free on 32 bit machines, so why not?

Remove __P.

Reveiwed by: benno

Complete rework of the PowerPC pmap and a number of other bits in the early
boot sequence.

The new pmap.c is based on NetBSD's newer pmap.c (for the mpc6xx processors)
which is 70% faster than the older code that the original pmap.c was based
on. It has also been based on the framework established by jake's initial
sparc64 pmap.c.

There is no change to how far the kernel gets (it makes it to the mountroot
prompt in psim) but the new pmap code is a lot cleaner.

Obtained from: NetBSD (pmap code)

[partially forced commit due to pilot error in earlier commit attempt]

{set,fill}_{,fp,db}regs() fixup:

- Add dummy {set,fill}_dbregs() on architectures that don't have them.

- KSEfy the powerpc versions (struct proc -> struct thread).

- Some architectures had the prototypes in md_var.h, some in reg.h, and
some in both; for consistency, move them to reg.h on all platforms.

These functions aren't really MD (the implementation is MD, but the interface
is MI), so they should move to an MI header, but I haven't figured out which
one yet.

Run-tested on i386, build-tested on Alpha, untested on other platforms.

vm_page_zero_idle() is no longer MD.

This commit (along with one pending in sys/dev/ofw and one in sys/conf) give
us our first minimal glimpse of PowerPC support.

With this code we can get to the "mountroot>" prompt on my Apple iMac. We
can't get any further due to lack of clock and interrupt handling, among other
things. This does however mean that pmap and VM are initialising.

We're fairly dependant on OpenFirmware at this point, but I hope to add
support for other classes of firmware at a later stage.

Reviewed by: obrien, dfr

Next phase in the PCI subsystem cleanup.

- Move PCI core code to dev/pci.
- Split bridge code out into separate modules.
- Remove the descriptive strings from the bridge drivers. If you
want to know what a device is, use pciconf. Add support for
broadly identifying devices based on class/subclass, and for
parsing a preloaded device identification database so that if
you want to waste the memory, you can identify *anything* we know
about.
- Remove machine-dependant code from the core PCI code. APIC interrupt
mapping is performed by shadowing the intline register in machine-
dependant code.
- Bring interrupt routing support to the Alpha
(although many platforms don't yet support routing or mapping
interrupts entirely correctly). This resulted in spamming
<sys/bus.h> into more places than it really should have gone.
- Put sys/dev on the kernel/modules include path. This avoids
having to change *all* the pci*.h includes.

Remove the last of the MD netisr code. It is now all MI. Remove
spending, which was unused now that all software interrupts have
their own thread. Make the legacy schednetisr use an atomic op
for setting bits in the netisr mask.

Reviewed by: jhb

- Overhaul the software interrupt code to use interrupt threads for each
type of software interrupt. Roughly, what used to be a bit in spending
now maps to a swi thread. Each thread can have multiple handlers, just
like a hardware interrupt thread.
- Instead of using a bitmask of pending interrupts, we schedule the specific
software interrupt thread to run, so spending, NSWI, and the shandlers
array are no longer needed. We can now have an arbitrary number of
software interrupt threads. When you register a software interrupt
thread via sinthand_add(), you get back a struct intrhand that you pass
to sched_swi() when you wish to schedule your swi thread to run.
- Convert the name of 'struct intrec' to 'struct intrhand' as it is a bit
more intuitive. Also, prefix all the members of struct intrhand with
'ih_'.
- Make swi_net() a MI function since there is now no point in it being
MD.

Submitted by: cp

- Heavyweight interrupt threads on the alpha for device I/O interrupts.
- Make softinterrupts (SWI's) almost completely MI, and divorce them
completely from the x86 hardware interrupt code.
- The ihandlers array is now gone. Instead, there is a MI shandlers array
that just contains SWI handlers.
- Most of the former machine/ipl.h files have moved to a new sys/ipl.h.
- Stub out all the spl*() functions on all architectures.

Submitted by: dfr

Support bounce buffers for ISA DMA on the alpha. This is required for the
irongate chipset (used in the UP1000) which does not support scatter/gather
DMA. We'll still use scatter gather if the core logic chipset supports it.

Reviewed by: dfr

Handle PCI devices that actually use an ISA IRQ for the cia and tsunami
chipsets. An example of this is the USB controller on these chipsets.
With this, I can now use USB devices on the test Alpha I am borrowing at
the moment.

Reviewed by: dfr, obrien

Update the ata driver to take more advantage of newbus, this
was needed to make attach/detach of devices work, which is
needed for the PCCARD support.
(PCCARD support is still not working though, more to come on that)

Support the CMD646 chip which is used on many alphas, sadly only
in WDMA2 mode, as the silicon is broken beyond belief for UDMA modes.

Lots of cosmetic fixes here and there.

Sorry for the size of this megapatchfromhell but it was not
possible otherwise...

newbus patches based on work from: dfr (Doug Rabson)

$Id$ -> $FreeBSD$

Add alpha_platform_setup_ide_intr() and alpha_platform_assign_pciintr()
prototypes.

Declare busdma_swi() like on i386 version.

Add the ability to specify where on the at_shutdown queue a handler is
installed.

Remove cpu_power_down, and replace it with an entry at the end of the
SHUTDOWN_FINAL queue in the only place it's used (APM).

Submitted by: Some ideas from Bruce Walter <walter@fortean.com>

Automatically detect which disk was booted and change the root to that disk.

Add new functions fill_fpregs() and set_fpregs(), like fill_regs()
and set_regs() but for the floating point register state. The code
is stolen from procfs_machdep.c, and moved out of there into
machdep.c.

These functions are needed for generating ELF core dumps.

Overhaul the spl system so that it actually works properly.

Add initial support for the FreeBSD/alpha kernel. This is very much a
work in progress and has never booted a real machine. Initial
development and testing was done using SimOS (see
http://simos.stanford.edu for details). On the SimOS simulator, this
port successfully reaches single-user mode and has been tested with
loads as high as one copy of /bin/ls :-).

Obtained from: partly from NetBSD/alpha