sys: Remove $FreeBSD$: one-line .c comment pattern

Remove /^/[*/]\s*\$FreeBSD\$.*\n/

ixl: Fix a mechanical mess-up in DrvAPI conversion

ixl_iw.c is not compiled by default, and I missed this in code
inspection.

Reported by: erj@
Sponsored by: Juniper Networks, Inc.

Convert iflib(4) and iflib-based drivers to the DrvAPI

Summary:
Convert iflib(4) and the following drivers:
* axgbe
* em
* ice
* ixl
* vmxnet

Sponsored by: Juniper Networks, Inc.
Reviewed by: kbowling, #iflib
Differential Revision: https://reviews.freebsd.org/D37768

ixl(4): Fix VLAN HW filtering

X700 family of controllers has limited number of available VLAN
HW filters. Driver did not handle properly a case when user
assigned more VLANs to the interface which had all filters
already in use. Fix that by disabling HW filtering when
it is impossible to create filters for all requested VLANs.
Keep track of registered VLANs using bitstring to be able
to re-enable HW filtering when number of requested VLANs
drops below the limit.

Also switch all allocations to use M_IXL malloc type
to ease detecting memory leaks in the driver.

Reviewed by: erj
Tested by: gowtham.kumar.ks@intel.com
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D28137

- Stop iflib(4) from leaking MSI messages on detachment by calling
bus_teardown_intr(9) before pci_release_msi(9).
- Ensure that iflib(4) and associated drivers pass correct RIDs to
bus_release_resource(9) by obtaining the RIDs via rman_get_rid(9)
on the corresponding resources instead of using the RIDs initially
passed to bus_alloc_resource_any(9) as the latter function may
change those RIDs. Solely em(4) for the ioport resource (but not
others) and bnxt(4) were using the correct RIDs by caching the ones
returned by bus_alloc_resource_any(9).
- Change the logic of iflib_msix_init() around to only map the MSI-X
BAR if MSI-X is actually supported, i. e. pci_msix_count(9) returns
> 0. Otherwise the "Unable to map MSIX table " message triggers for
devices that simply don't support MSI-X and the user may think that
something is wrong while in fact everything works as expected.
- Put some (mostly redundant) debug messages emitted by iflib(4)
and em(4) during attachment under bootverbose. The non-verbose
output of em(4) seen during attachment now is close to the one
prior to the conversion to iflib(4).
- Replace various variants of spelling "MSI-X" (several in messages)
with "MSI-X" as used in the PCI specifications.
- Remove some trailing whitespace from messages emitted by iflib(4)
and change them to consistently start with uppercase.
- Remove some obsolete comments about releasing interrupts from
drivers and correct a few others.

Reviewed by: erj, Jacob Keller, shurd
Differential Revision: https://reviews.freebsd.org/D18980

ixl(4): Update version number to 2.0.0-k

And update copyrights to current year.

MFC after: 1 month
Sponsored by: Intel Corporation

ixl(4): Update to 1.9.9-k

Refresh upstream driver before impending conversion to iflib.

Major changes:

- Support for descriptor writeback mode (required by ixlv(4) for AVF support)
- Ability to disable firmware LLDP agent by user (PR 221530)
- Fix for TX queue hang when using TSO (PR 221919)
- Separate descriptor ring sizes for TX and RX rings

PR: 221530, 221919
Submitted by: Krzysztof Galazka <krzysztof.galazka@intel.com>
Reviewed by: #IntelNetworking
MFC after: 1 day
Relnotes: Yes
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D14985

ixl(4): Update to 1.7.12-k

Refresh upstream driver before impending conversion to iflib.

Major new features:

- Support for Fortville-based 25G adapters
- Support for I2C reads/writes

(To prevent getting or sending corrupt data, you should set
dev.ixl.0.debug.disable_fw_link_management=1 when using I2C
[this will disable link!], then set it to 0 when done. The driver implements
the SIOCGI2C ioctl, so ifconfig -v works for reading I2C data,
but there are read_i2c and write_i2c sysctls under the .debug sysctl tree
[the latter being useful for upper page support in QSFP+]).

- Addition of an iWARP client interface (so the future iWARP driver for
X722 devices can communicate with the base driver).
- Compiling this option in is enabled by default, with "options IXL_IW" in
GENERIC.

Differential Revision: https://reviews.freebsd.org/D9227
Reviewed by: sbruno
MFC after: 2 weeks
Sponsored by: Intel Corporation