sys: Remove $FreeBSD$: two-line .h pattern

Remove /^\s*\*\n \*\s+\$FreeBSD\$$\n/

kbdreg.h: include opt_kbd.h

This is a kernel-only file, so it's safe to include opt_kbd.h. However,
add #ifdef _KERNEL guards to emphasize that. And also move the include
of opt_kbd.h in atkbdcreg.h to inside the kernel guards. Nothing outside
the kernel in tree uses the rest of that file, but I'm less comfortable
moving the #ifdef _KERNEL to the top of that file.

Sponsored by: Netflix

psm(4): Disable AUX multiplexer probing on all Lenovo laptops.

Rudimentary AUX multiplexing support was added to kernel to make possible
touchpad initialization on some HP EliteBook laptops with trackpoint.

Disable multiplexer probing on all Lenovo laptops now as they use touchpad
pass-through port rather than AUX multiplexer to connect trackpoint and
at least two model (X120e and X121e) is known for getting PS/2 AUX port
dysfunctional after switching back to hidden multiplexing mode.

AUX MUX probing can be reenabled with setting of hw.psm.mux_disabled loader
tunable to 0.

PR: 249987
Reported by: jwb
MFC after: 2 weeks

atkbdc: use proper pointer type for KBDC

Proper locking for atkbdc will likely replace the kbdc_lock mechanism
entirely with a mutex in atkbdc_softc, so that other consumers can also
properly ensure locking protocol is followed (e.g. psm.c:doinitialize).

The first step to doing this neatly is making KBDC less opaque so that
others don't have to jump through weird casting hoops to address the mutex.

No functional change intended; this diff effectively just removes a bunch of
casting. A future change may remove the KBDC typedef entirely and just opt
for using `atkbdc_softc_c *` directly, but this was decidedly a good
intermediate step to make these changes simple to audit.

psm(4): Add minimal support for active AUX port multiplexers

Active PS/2 multiplexing is a method for attaching up to four PS/2
pointing devices to a computer. Enabling of multiplexed mode allows
commands to be directed to individual devices using routing prefixes.
Multiplexed mode reports input with each byte tagged to identify
its source. This method differs from one currently supported by psm(4)
where so called guest device (trackpoint) is attached to special
interface located on the host device (touchpad) and latter performs
guest protocol conversion to special encapsulation packet format.

At present time active PS/2 multiplexing is used in some models of
HP laptops e.g. EliteBook 8560w, 9470m. Enabling of absolute operation
mode on such touchpads is connected with following problems:
1. Touchpad's port priority is lower than trackpoint's. That blocks
information queries thus prevents touchpad detection and configuration.
2. Touchpad and trackpoint have different protocol packet sizes and
sync bytes.

As PS/2 usage is on decline only minimal possible set of changes to
support Synaptics touchpad and generic mouses is implemented.
Active multiplexing mode is enabled only at probe stage to scan through
attached PS/2 devices to query and configure Synaptics touchpad.
After touchpad has been configured, mux is switched back to legacy
(hidden multiplexing) mode to perform normal interrupt-driven input
data processing. Overflow bit values rather than tags are used to
separate packets produced by different devices. Switching back to
legacy mode allows to avoid psm(4) and atkbd(4) rework to support
4 instances of mouse driver.

Note: While in hidden multiplexing mode KBC does some editing of the
packet stream. It remembers the button bits from the last packet
received from each device, and replaces the button bits of every
packet with the logical OR of all devices’ most recent button bits.
This sort of button crosstalk results in spurious button events
which are inhibitted with various tricks. E.g. trackpoint middle
button events are suppressed while trackpad surface is touched and
touchpad left and right button events are suppressed if corresponding
trackpoint buttons are pressed.

PR: 231058
Reported by: Michael Figiel <mifigiel@gmail.com>
Tested by: Michael Figiel <mifigiel@gmail.com>
MFC after: 2 weeks

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.

Quirk based support of Chromebook keyboard found in Acer C720

This probably supports other devices based on SeaBIOS, which need
to be added to the smbios based quirks table.

The functionality has been ported from DragonFlyBSD and adapted
to FreeBSD's more general purpose environment.

Devices not covered by a quirk shouldn't be affected at all. Thanks
to jhb and kostikbel for reviewing the code.

Reviewed by: kostikbel, jhb
Approved by: jhb, kostikbel
Differential Revision: https://reviews.freebsd.org/D1802

- If the atkbdc device is assigned an IRQ resource by ACPI or the PnPBIOS,
allow the child atkbd device to reuse that IRQ resource instead of
reallocating the same IRQ from the parent bus inside the atkbd driver.
- Don't allocate a shared IRQ for the atkbd driver. For AT keyboard
devices on an ISA bus the IRQ is not shareable. Instead, the bus driver
should mark the IRQ shareable if the bus supports shared IRQs.
- Don't identify child devices until after the atkbdc device itself has
attached.

A new jail(8) with a configuration file, to replace the work currently done
by /etc/rc.d/jail.

On certain chipsets AT keyboard controller isn't present and is
emulated by BIOS using SMI interrupt. On those chipsets reading
from the status port may be thousand times slower than usually.
Sometimes this emilation is not working properly resulting in
commands timing out and since we assume that inb() operation
takes very little time to complete we need to adjust number of
retries to keep waiting time within a designed limits (100ms).
Measure time it takes to make read_status() call and adjust
number of retries accordingly.

To keep it simple, use TSC to measure inb() performance and
keep it to amd64-only, since TSC may not available on older
CPUs.

Also enable detection of the AT controller absence on amd64.

Reviewed by: jhb
MFC after: 1 month

- Import the HEAD csup code which is the basis for the cvsmode work.

- Hook up the new locations of the atkbdc(4), atkbd(4) and psm(4) source
files after they were repo-copied to sys/dev/atkbdc. The sources of
atkbdc(4) and its children were moved to the new location in preparation
for adding an EBus front-end to atkbdc(4) for use on sparc64; i.e. in
order to not further scatter them over the whole tree which would have
been the result of adding atkbdc_ebus.c in e.g. sys/sparc64/ebus. Another
reason for the repo-copies was that some of the sources were misfiled,
e.g. sys/isa/atkbd_isa.c wasn't ISA-specific at all but for hanging
atkbd(4) off of atkbdc(4) and was renamed to atkbd_atkbdc.c accordingly.
Most of sys/isa/psm.c, i.e. expect for its PSMC PNP part, also isn't
ISA-specific.
- Separate the parts of atkbdc_isa.c which aren't actually ISA-specific
but are shareable between different atkbdc(4) bus front-ends into
atkbdc_subr.c (repo-copied from atkbdc_isa.c). While here use
bus_generic_rl_alloc_resource() and bus_generic_rl_release_resource()
respectively in atkbdc_isa.c instead of rolling own versions.
- Add sparc64 MD bits to atkbdc(4) and atkbd(4) and an EBus front-end for
atkbdc(4). PS/2 controllers and input devices are used on a couple of
Sun OEM boards and occur on either the EBus or the ISA bus. Depending on
the board it's either the only on-board mean to connect a keyboard and
mouse or an alternative to either RS232 or USB devices.
- Wrap the PSMC PNP part of psm.c in #ifdef DEV_ISA so it can be compiled
without isa(4) (e.g. for EBus-only machines). This ISA-specific part
isn't separated into its own source file, yet, as it requires more work
than was feasible for 6.0 in order to do it in a clean way. Actually
philip@ is working on a rewrite of psm(4) so a more comprehensive
clean-up and separation of hardware dependent and independent parts is
expected to happen after 6.0.

Tested on: i386, sparc64 (AX1105, AXe and AXi boards)
Reviewed by: philip

Add support for the A4 Tech RFSW-35 mouse wheel. Probe is similar to
4D Plus.

PR: 44333

Include "opt_kbd.h" since certain structures size depend on the value
of KBDIO_DEBUG which may be defined in the kernel config (as it is in NOTES).

This kind of bug is a _really_ horribly thing as we end up with one bit
of code thinking a particular structure is 136 bytes and another that it
is only 112 bytes.

Ideally all places would remember to #include the right "opt_foo.h" file,
but I think in practice file containing the variable sized struct should
#include it explicitly as a precaution.

Detected by: FlexeLint

Refine ACPI/PnP BIOS probe/attach routines a bit.

- Add workaround for the problematic PnP BIOS which does not assign
irq resource for the PS/2 mouse device node; if there is no irq
assigned for the PS/2 mouse node, refer to device.hints for an
irq number. If we still don't find an irq number in the hints
database, use a hard-coded value.
- Delete unused ivars.
- Bit of clean up in probe/attach.
- Add PnP ID for the PS/2 mouse port on some IBM ThinkPad models.

Update the atkbdc, atkbd, and psm drivers to probe/attach
more cleanly and consistently in all APCI, PnP BIOS, and "hint"
cases.

NOTE: this doesn't necessarily solve the problem that the PS/2
mouse is not detected after the recent ACPI update.

- Properly keep track of I/O port resources.
- Use bus_space_read/write() to access the ports.

- Add Support for the following PS/2 mice:
- Microsoft IntelliMouse Explorer: 2 buttons on top, 2 side buttons
and a wheel which also acts as the middle button. The mouse is
recognized as "IntelliMouse Explorer".
- Genius NetScroll Optical: 2 buttons on top, 2 side buttons and a
wheel which also acts as the middle button. The mouse is recognized
as "NetMouse/NetScroll Optical".
- MouseSystems SmartScroll Mouse (OEM from Genius?): 3 buttons on top,
1 side button and a wheel. The mouse is recognized as Genius
"NetScroll".
- IBM ScrollPoint: 2 buttons on top and a stick between the buttons.
The stick can perform "horizontal scroll" in W*ndows environment.
The horizontal movement of the stick is detected. It is currently
mapped to the Z axis movement in the same way as the first wheel.
The mouse is recognized as "MouseMan+", as it is considered to be
a variation of MouseMan.
- A4 Tech 4D and 4D+ mice. These mice have two wheels! The movement
of the second wheel is reported as the Z axis movement in the
same way as the first wheel. These mice are recognized as "4D
Mouse" and "4D+ Mouse".
- Tweak IntelliMouse support code a bit so that less-than-compatible
wheel mice can work properly with the psm driver.
- Add driver configuration flags which correspond to the kernel
options PSM_HOOKRESUME and PSM_RESETAFTERSUSPEND, so that we don't
need to recompile the kernel when we need these functions.
- Properly keep track of the irq resource.
- Add a watchdog timer in case interrupts are lost (experimental).
- Add `detach' function (experimental).

Change #ifdef KERNEL to #ifdef _KERNEL in the public headers. "KERNEL"
is an application space macro and the applications are supposed to be free
to use it as they please (but cannot). This is consistant with the other
BSD's who made this change quite some time ago. More commits to come.

$Id$ -> $FreeBSD$

Slight reorganization of internal interface in the keyboard controller
driver.

Add the new keyboard driver and video card driver. They will be
used by console drivers.

(They are not yet activated yet. Wait for announcement later.)