Copy stable/9 to releng/9.3 as part of the 9.3-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Copy head to stable/9 as part of 9.0-RELEASE release cycle.

Approved by: re (implicit)

Change return code semantics of start_scan_locked(). Instead of reporting
if a scan is running, report if a scan has been started. The return value
itself is not (yet) used anywhere in the tree and it is also not exported
to userspace.

MFC after: 1 month

Honor the IEEE80211_SCAN_BGSCAN flag, which makes it possible to actually
request a background scan using IEEE80211_IOC_SCAN_BGSCAN.

MFC after: 1 month

Implementation of the upcoming Wireless Mesh standard, 802.11s, on the
net80211 wireless stack. This work is based on the March 2009 D3.0 draft
standard. This standard is expected to become final next year.
This includes two main net80211 modules, ieee80211_mesh.c
which deals with peer link management, link metric calculation,
routing table control and mesh configuration and ieee80211_hwmp.c
which deals with the actually routing process on the mesh network.
HWMP is the mandatory routing protocol on by the mesh standard, but
others, such as RA-OLSR, can be implemented.

Authentication and encryption are not implemented.

There are several scripts under tools/tools/net80211/scripts that can be
used to test different mesh network topologies and they also teach you
how to setup a mesh vap (for the impatient: ifconfig wlan0 create
wlandev ... wlanmode mesh).

A new build option is available: IEEE80211_SUPPORT_MESH and it's enabled
by default on GENERIC kernels for i386, amd64, sparc64 and pc98.

Drivers that support mesh networks right now are: ath, ral and mwl.

More information at: http://wiki.freebsd.org/WifiMesh

Please note that this work is experimental. Also, please note that
bridging a mesh vap with another network interface is not yet supported.

Many thanks to the FreeBSD Foundation for sponsoring this project and to
Sam Leffler for his support.
Also, I would like to thank Gateworks Corporation for sending me a
Cambria board which was used during the development of this project.

Reviewed by: sam
Approved by: re (kensmith)
Obtained from: projects/mesh11s

calls callout_drain(9) to un-schedule a scan timer to prevent a page
fault in softclock.

Submitted by: sam
Reviewed by: jhb, sam (original version), thompsa

Overhaul monitor mode handling:
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi

Reviewed by: cbzimmer, rpaulo, thompsa

Create a taskqueue for each wireless interface which provides a serialised
sleepable context for net80211 driver callbacks. This removes the need for USB
and firmware based drivers to roll their own code to defer the chip programming
for state changes, scan requests, channel changes and mcast/promisc updates.
When a driver callback completes the hardware state is now guaranteed to have
been updated and is in sync with net80211 layer.

This nukes around 1300 lines of code from the wireless device drivers making
them more readable and less race prone.

The net80211 layer has been updated as follows
- all state/channel changes are serialised on the taskqueue.
- ieee80211_new_state() always queues and can now be called from any context
- scanning runs from a single taskq function and executes to completion. driver
callbacks are synchronous so the channel, phy mode and rx filters are
guaranteed to be set in hardware before probe request frames are
transmitted.

Help and contributions from Sam Leffler.

Reviewed by: sam

o add ic_rt to track the rate table for the current channel; this enables
calculation of packet transmit times to do things like check txop limits
o remove equivalent driver code and convert to use net80211 state

display min/max dwell times in msecs in debug msgs

Add modes for 1/2 and 1/4-width channels so we have separate roaming
and xmit parameters. This makes it possible to use tdma on fractional
channels.
o add IEEE80211_MODE_HALF and IEEE80211_MODE_QUARTER; note these are
band-agnostic (may need revisiting)
o setup all default rates in ic_sup_rates instead of doing it only
for active modes; we need these to calculate the default tx parameters
which are not recalculated after a regulatory update (can't just
recalculate after installing a new channel list because we might
clobber user settings)
o remove special case code in ieee80211_get_suprates; this is now
a candidate for an inline or removal
o add various entries for new modes (roaming+tx params, wme, rate
mapping, scan set setup, country ie construction, tdma, basic rates)

Note these modes are intentionally not visible through if_media.

simplify setting up the roaming parameters; writing default parameters only
for active modes hasn't turned out to be useful so just define a const table
and copy it in place

convert MALLOC/FREE to malloc/free

Revert the removal of the MALLOC and FREE macros from the net80211 code.

Requested by: sam

Retire the MALLOC and FREE macros. They are an abomination unto style(9).

MFC after: 3 months

Simplify some contorted logic that wrongly left ISCAN_DISCARD set
in certain cases causing the current ap to be lost from the scan cache.

Obtained from: Atheros (original bug)

Revise lock name handling:
o construct a name for the com lock as done for other locks
o pass the device name to IEEE80211_LOCK_INIT so the mtx name
is constructed as foo_com_lock
o introduce *_LOCK_OBJ macro's to hide the lock contents and
minimize redundant code

Multi-bss (aka vap) support for 802.11 devices.

Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.

Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)

silence complaint about not loading the wlan_scan_monitor module;
it does not exist and is not needed as monitor mode operation has
always required setting the current channel

Reviewed by: thompsa
MFC after: 1 week

Fix scanning issues since the new net80211 code went in
- provide dummy routines for ic_scan_curchan and ic_scan_mindwell, we do not support those operations.
- add ieee80211_scan_done() to tell the scanning module that all channels have been scanned.
- pass IEEE80211_S_SCAN state off to net80211 so it can initiate scanning
- fix overflow in the rates array
- scale the rate value passed back from the firmware scan to the units that net80211 uses.

Submitted by: Token
Reviewed by: sam, avatar
Approved by: re (kensmith)

Change the channel number in the scan results struct to be a pointer to the
operating channel and use this in the scan cache rather than directly using
ic_curchan. Some firmware cards can only do a full scan and so ic_curchan does
not have the correct value.

Also add IEEE80211_CHAN2IEEE to directly dereference ic_ieee from the channel
to be used in the fast path.

Reviewed by: sam, sephe
Approved by: re (kensmith)

Update 802.11 wireless support:
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing

Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested

This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.