| #
252814 |
|
05-Jul-2013 |
np |
- MFC r252661, r252705, r252711, r252715, r252716, r252724, r252728,
r252747.
- Connect t3_tom and t4_tom to the build (r252555 enables them).
r252661:
- Include the T5 firmware with the driver.
- Update the T4 firmware to the latest.
- Minor reorganization and updates to the version macros, etc.
r252705:
- Read all TP parameters in one place.
- Read the filter mode, calculate various shifts, and use them
properly during active open (in select_ntuple).
r252711:
The T5 allows the driver to specify the ISS. Do so; use the ISS picked
by the kernel.
r252715:
Ring the egress queue's doorbell as soon as there are 8 or more
descriptors ready to be processed.
r252716:
Pay attention to TCP_NODELAY when it's set/unset after the connection
is established.
r252724:
On-the-fly changes to the interrupt coalescing timer should apply to the
TOE rx queues too.
r252728:
- Make note of interface MTU change if the rx queues exist, and not just
when the interface is up.
- Add a tunable to control the TOE's rx coalesce feature (enabled by
default as it always has been). Consider the interface MTU or the
coalesce size when deciding which cluster zone to use to fill the
offload rx queue's free list. The tunable is:
dev.{t4nex,t5nex}.<N>.toe.rx_coalesce
r252747:
- Show the reason why link is down if this information is available.
- Display the temperature and PHY firmware version of the BT PHY.
|
| #
252495 |
|
02-Jul-2013 |
np |
MFC all cxgbe(4) changes missing from stable/9:
r248925, r249368, r249370, r249376, r249382, r249383, r249385, r249391,
r249392, r249393, r249627, r249629, r250090, r250092, r250093, r250117,
r250218, r250221, r250614, r251213, r251317, r251358, r251434, r251518,
r251638, r252312, r252469, r252470, r250697(kib).
r248925:
Support for Chelsio's 40G Terminator 5 (aka T5) ASIC.
...
r249368:
Set and display the IP fragment bit correctly when dealing with
the filter mode.
r249370:
cxgbe(4): Ensure that the MOD_LOAD handler runs before either t4nex or
t5nex attach to their devices.
r249376:
- Explain clearly why a different firmware is being installed (if/when
it is being installed). Improve other error messages while here.
- Select special FPGA specific configuration profile when appropriate.
r249382:
There is no need for elaborate queries and error checking when trying to
set FW4MSG_ENCAP.
r249383:
Get rid of a couple of stray \n's.
r249385:
cxgbe/tom: Slight simplification of code that calculates options2.
r249391:
Auto-reduce the holdoff timers that are greater than the maximum value
allowed by the hardware.
r249392:
Cosmetic change (s/wrwc/wcwr/;s/WRWC/WCWR/).
r249393:
Add pciids of the T5 based cards. The ones that I haven't tested with
cxgbe(4) are disabled for now. This will change.
r249627:
cxgbe/tom: Update the CLIP table on the chip when there are changes
to the list of IPv6 addresses on the system. The table is used for
TOE+IPv6 only.
r249629:
cxgbe(4): Refuse to install T5 firmwares on a T4 card (and vice versa).
r250090:
cxgbe(4): Some updates to shared code.
r250092:
- Provide accurate ifmedia information so that 40G ports/transceivers are
displayed properly in ifconfig, etc.
- Use the same number of tx and rx queues for a 40G port as for a 10G port.
r250093:
Attach to the T580 (2 x 40G) card.
r250117:
Fix DDP breakage introduced in r248925. Bitwise OR has higher
precedence than ternary conditional.
r250218:
cxgbe/tom: Do not use M_PROTO1 to mark rx zero-copy mbufs as special.
All the M_PROTOn flags are clobbered when an mbuf is appended to the
socket buffer.
r250221:
cxgbe: Switch to a better way to install firmware.
r250614:
Deal correctly with 40G ports that don't have any transceiver plugged
in. Do not claim that they have unknown tranceivers.
r251213:
cxgbe(4): Some more debug sysctls. These work on both T4 and T5 based
cards.
r251317:
cxgbe(4): t4fw_cfg must be explicitly loaded if the driver is being
loaded via loader.conf.
r251358:
cxgbe(4): Provide accurate hit count for filters on T5 cards. The
location within the TCB and the size have both changed.
r251434:
cxgbe(4): Never install a firmware if hw.cxgbe.fw_install is 0.
r251518:
cxgbe/tom: Fix bad signed/unsigned mixup in the stid allocator. This
fixes a panic when allocating a mixture of IPv6 and IPv4 stids.
r251638:
cxgbe/tom: Allow caller to select the queue (control or data) used to
send the CPL_SET_TCB_FIELD request in t4_set_tcb_field().
r252312:
Update T5 register ranges. This is so that regdump skips over registers
with read side-effects.
r252469:
Add a sysctl to get the number of filters available.
sysctl dev.t4nex.<N>.nfilters
sysctl dev.t5nex.<N>.nfilters
r252470:
Count the number of hits for a filter by default.
r250697:
Add dependencies on the firmware, which allows the loading of the cxgb
and cxgbe modules.
|
| #
237920 |
|
01-Jul-2012 |
np |
Backport just the sys/{dev,modules}/cxgb{,e}/ parts of r237263, and then
disable the TOE and iWARP modules in the Makefiles (they won't compile
without the rest of r237263).
This reduces diffs between the cxgb/cxgbe drivers in head and 9 and
makes it easy to MFC other fixes to 9.
|