Copy stable/9 to releng/9.3 as part of the 9.3-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Copy head to stable/9 as part of 9.0-RELEASE release cycle.

Approved by: re (implicit)

Remove duplicate header includes

The previous commit didn't completely rename this to what it should be.

Refactor out the ar71xx mac address code into something that's
just for Redboot.

At some point we're going to need to build options for different
boot environments - for example, the UBoot setups I've seen simply
have the MAC address hard-coded at a fixed location in flash.
The OpenWRT support simply yanks the if_arge MAC directly from that
in code, rather than trying to find a uboot environment to pull it
from.

Add an option - AR71XX_REALMEM - which overrides the amount of
memory detected from Redboot, or overrides the "otherwise" case
if no Redboot information was found.

Some AR71XX platforms don't use Redboot (eg TP-LINK devices using
UBoot; some later Ubiquiti devices which apparently also use
UBoot) and at least one plain out lies - the Ubiquiti LS-SR71A
Redboot says there's 16mb of RAM when in fact there's 32mb.

A more "clean" solution will be needed at a later date.

- Populate dump_avail with proper values from phys_avail

Make a note of which platforms the mac strings come from.

Suggested by: adrian

Use getenv to find the mac address since it could be in the bootloader
environment or command line and under different names.

Remove now unused 'reg'.

Initialise the USB system using cpuops rather than the AR71XX specific method.

Migrate the CPU reset path to use the new cpuops.

Preparation work for supporting the AR91xx and AR724x.

* Implement a SoC probe function, from Linux, which determines the
SoC family, type and revision. This only probes the AR71xx series
SoC and (currently) panics on others.

* Migrate some of the AR71XX specific hardware init (USB device, determining
system frequencies) into using the cpuops introduced in an earlier commit.
Other SoC specific hardware stuff (per-device flush/WB, GPIO pin wiring,
Ethernet PLL setup, other things I've likely missed) will be introduced in
subsequent commits.

Reviewed by: imp@
Obtained from: (partially) Linux

- Call post-boot fixup function in order to get proper static
symbols resolving in DDB
- When zeroing .bss/.sbss do not round end address to page boundary,
it's not neccessary and might destroy data pased by trampoline or
boot loader

Update from old DDB convetion to initialize debugger to new KDB way.
Always call kdb_init(). If we have KDB enabled, then provide a handy
place to break to the debugger.

Set the svn:eol-style = native and svn:mime-type = text/plain
properties on all files in this tree.

Submitted by: rpaulo@

Place proper svn:keywords tag on all these files. They were created
somehow without them on projects/mips, and that mistake was propigated
over to head.

Submitted by: rpaulo@

Merge from projects/mips to head by hand:

Merge support files for the Atheros AR71xx (and soon AR9xxx)
processors, except files from sys/conf and sys/mips/conf. This work
was done primarily by Olecksandr Tymoshenko and works on the
RouterStation and RouterStation PRO. Other AR71xx-based boards have
been reported as working as well (RouterBoard, for example).

Rename mips_pcpu_init to mips_pcpu0_init since it applies only to the
BSP. Provide a missing prototype.

Centralize initialization of pcpu, and set curthread early...

With this commit our friend RMI will now compile. I have
not tested it and the chances of it running yet are about
ZERO.. but it will now compile. The hard part now begins,
making it run ;-)

Parse and save the command line passed in from RedBoot (exec -c "xxx") and also
the board specific environment variables.

This is not ar71xx specific and should be shared better.

- Move CPU/AHB frequency calculations to functions to
prevent code duplication

- ar71xx increases Count value every two cycles

- Get memory size and base MAC address from RedBoot (if available)

- Calculate CPU frequency using dividers from PLL registers

- Revert changes accidentally killed by merge operation

- Reset USB chip and init control registers

- Rename RESET-related registers
- Add PCI registers

- Forgot to add this file to r187515

- Use ATH_READ_REG/ATH_WRITE_REG instead of direct memory access

- Fix platform_reset function

- Use more generic name for atheros-based devices subdirectory. Keep old
naming scheme for files until we'll figure out common parts.

Suggested by: imp@

- style(9) fix: replace spaces with tabs

- First bits of Atheros' AR71XX port. Only UART supported ATM.