Copy stable/9 to releng/9.3 as part of the 9.3-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Copy head to stable/9 as part of 9.0-RELEASE release cycle.

Approved by: re (implicit)

- If the atkbdc device is assigned an IRQ resource by ACPI or the PnPBIOS,
allow the child atkbd device to reuse that IRQ resource instead of
reallocating the same IRQ from the parent bus inside the atkbd driver.
- Don't allocate a shared IRQ for the atkbd driver. For AT keyboard
devices on an ISA bus the IRQ is not shareable. Instead, the bus driver
should mark the IRQ shareable if the bus supports shared IRQs.
- Don't identify child devices until after the atkbdc device itself has
attached.

On certain chipsets AT keyboard controller isn't present and is
emulated by BIOS using SMI interrupt. On those chipsets reading
from the status port may be thousand times slower than usually.
Sometimes this emilation is not working properly resulting in
commands timing out and since we assume that inb() operation
takes very little time to complete we need to adjust number of
retries to keep waiting time within a designed limits (100ms).
Measure time it takes to make read_status() call and adjust
number of retries accordingly.

To keep it simple, use TSC to measure inb() performance and
keep it to amd64-only, since TSC may not available on older
CPUs.

Also enable detection of the AT controller absence on amd64.

Reviewed by: jhb
MFC after: 1 month

- Hook up the new locations of the atkbdc(4), atkbd(4) and psm(4) source
files after they were repo-copied to sys/dev/atkbdc. The sources of
atkbdc(4) and its children were moved to the new location in preparation
for adding an EBus front-end to atkbdc(4) for use on sparc64; i.e. in
order to not further scatter them over the whole tree which would have
been the result of adding atkbdc_ebus.c in e.g. sys/sparc64/ebus. Another
reason for the repo-copies was that some of the sources were misfiled,
e.g. sys/isa/atkbd_isa.c wasn't ISA-specific at all but for hanging
atkbd(4) off of atkbdc(4) and was renamed to atkbd_atkbdc.c accordingly.
Most of sys/isa/psm.c, i.e. expect for its PSMC PNP part, also isn't
ISA-specific.
- Separate the parts of atkbdc_isa.c which aren't actually ISA-specific
but are shareable between different atkbdc(4) bus front-ends into
atkbdc_subr.c (repo-copied from atkbdc_isa.c). While here use
bus_generic_rl_alloc_resource() and bus_generic_rl_release_resource()
respectively in atkbdc_isa.c instead of rolling own versions.
- Add sparc64 MD bits to atkbdc(4) and atkbd(4) and an EBus front-end for
atkbdc(4). PS/2 controllers and input devices are used on a couple of
Sun OEM boards and occur on either the EBus or the ISA bus. Depending on
the board it's either the only on-board mean to connect a keyboard and
mouse or an alternative to either RS232 or USB devices.
- Wrap the PSMC PNP part of psm.c in #ifdef DEV_ISA so it can be compiled
without isa(4) (e.g. for EBus-only machines). This ISA-specific part
isn't separated into its own source file, yet, as it requires more work
than was feasible for 6.0 in order to do it in a clean way. Actually
philip@ is working on a rewrite of psm(4) so a more comprehensive
clean-up and separation of hardware dependent and independent parts is
expected to happen after 6.0.

Tested on: i386, sparc64 (AX1105, AXe and AXi boards)
Reviewed by: philip

Forced commit to denote that the following repo-copies have taken place:

sys/dev/kbd/atkbd.c -> sys/dev/atkbdc/atkbd.c
sys/dev/kbd/atkbdc.c -> sys/dev/atkbdc/atkbdc.c
sys/dev/kbd/atkbdcreg.h -> sys/dev/atkbdc/atkbdcreg.h
sys/dev/kbd/atkbdreg.h -> sys/dev/atkbdc/atkbdreg.h
sys/isa/atkbd_isa.c -> sys/dev/atkbdc/atkbd_atkbdc.c
sys/isa/atkbdc_isa.c -> sys/dev/atkbdc/atkbdc_isa.c
sys/isa/atkbdc_isa.c -> sys/dev/atkbdc/atkbdc_subr.c
sys/isa/psm.c -> sys/dev/atkbdc/psm.c

Repo-copies done by: markm

Add support for the A4 Tech RFSW-35 mouse wheel. Probe is similar to
4D Plus.

PR: 44333

Include "opt_kbd.h" since certain structures size depend on the value
of KBDIO_DEBUG which may be defined in the kernel config (as it is in NOTES).

This kind of bug is a _really_ horribly thing as we end up with one bit
of code thinking a particular structure is 136 bytes and another that it
is only 112 bytes.

Ideally all places would remember to #include the right "opt_foo.h" file,
but I think in practice file containing the variable sized struct should
#include it explicitly as a precaution.

Detected by: FlexeLint

Refine ACPI/PnP BIOS probe/attach routines a bit.

- Add workaround for the problematic PnP BIOS which does not assign
irq resource for the PS/2 mouse device node; if there is no irq
assigned for the PS/2 mouse node, refer to device.hints for an
irq number. If we still don't find an irq number in the hints
database, use a hard-coded value.
- Delete unused ivars.
- Bit of clean up in probe/attach.
- Add PnP ID for the PS/2 mouse port on some IBM ThinkPad models.

Update the atkbdc, atkbd, and psm drivers to probe/attach
more cleanly and consistently in all APCI, PnP BIOS, and "hint"
cases.

NOTE: this doesn't necessarily solve the problem that the PS/2
mouse is not detected after the recent ACPI update.

- Properly keep track of I/O port resources.
- Use bus_space_read/write() to access the ports.

- Add Support for the following PS/2 mice:
- Microsoft IntelliMouse Explorer: 2 buttons on top, 2 side buttons
and a wheel which also acts as the middle button. The mouse is
recognized as "IntelliMouse Explorer".
- Genius NetScroll Optical: 2 buttons on top, 2 side buttons and a
wheel which also acts as the middle button. The mouse is recognized
as "NetMouse/NetScroll Optical".
- MouseSystems SmartScroll Mouse (OEM from Genius?): 3 buttons on top,
1 side button and a wheel. The mouse is recognized as Genius
"NetScroll".
- IBM ScrollPoint: 2 buttons on top and a stick between the buttons.
The stick can perform "horizontal scroll" in W*ndows environment.
The horizontal movement of the stick is detected. It is currently
mapped to the Z axis movement in the same way as the first wheel.
The mouse is recognized as "MouseMan+", as it is considered to be
a variation of MouseMan.
- A4 Tech 4D and 4D+ mice. These mice have two wheels! The movement
of the second wheel is reported as the Z axis movement in the
same way as the first wheel. These mice are recognized as "4D
Mouse" and "4D+ Mouse".
- Tweak IntelliMouse support code a bit so that less-than-compatible
wheel mice can work properly with the psm driver.
- Add driver configuration flags which correspond to the kernel
options PSM_HOOKRESUME and PSM_RESETAFTERSUSPEND, so that we don't
need to recompile the kernel when we need these functions.
- Properly keep track of the irq resource.
- Add a watchdog timer in case interrupts are lost (experimental).
- Add `detach' function (experimental).

Change #ifdef KERNEL to #ifdef _KERNEL in the public headers. "KERNEL"
is an application space macro and the applications are supposed to be free
to use it as they please (but cannot). This is consistant with the other
BSD's who made this change quite some time ago. More commits to come.

$Id$ -> $FreeBSD$

Slight reorganization of internal interface in the keyboard controller
driver.

Add the new keyboard driver and video card driver. They will be
used by console drivers.

(They are not yet activated yet. Wait for announcement later.)