Copy stable/9 to releng/9.3 as part of the 9.3-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

MFC r242625:

Remove duplicate const specifiers in many drivers (I hope I got all of
them, please let me know if not). Most of these are of the form:

static const struct bzzt_type {
[...list of members...]
} const bzzt_devs[] = {
[...list of initializers...]
};

The second const is unnecessary, as arrays cannot be modified anyway,
and if the elements are const, the whole thing is const automatically
(e.g. it is placed in .rodata).

I have verified this does not change the binary output of a full kernel
build (except for build timestamps embedded in the object files).

Reviewed by: yongari, marius

MFC: r233282

- First pass at const'ifying ata(4) as appropriate.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.

MFC r232380:
Fix names of some Marvell SATA chips. It looks like chips with proprietary
interface supported by mvs(4) are 88SX, while AHCI-like chips are 88SE.

PR: kern/165271

Copy head to stable/9 as part of 9.0-RELEASE release cycle.

Approved by: re (implicit)

Several chipset drivers alter parameters relevant for the DMA tag creation,
i.e. alignment, max_address, max_iosize and segsize (only max_address is
thought to have an negative impact regarding this issue though), after
calling ata_dmainit() either directly or indirectly so these values have
no effect or at least no effect on the DMA tags and the defaults are used
for the latter instead. So change the drivers to set these parameters
up-front and ata_dmainit() to honor them.

Reviewd by: mav
MFC after: 1 month

Set of legacy mode SATA enchancements:
- Implement proper combined mode decoding for Intel controllers to properly
identify SATA and PATA channels and associate ATA channels with SATA ports.
This fixes wrong reporting and in some cases hard resets to wrong SATA ports.
- Improve SATA registers support to handle hot-plug events and potentially
interface errors. For ICH5/6300ESB chipsets these registers accessible via
PCI config space. For later ones they may be accessible via PCI BAR(5).
- For controllers not generating interrupts on hot-plug events, implement
periodic status polling. Use it to detect hot-plug on Intel and VIA
controllers. Same probably could also be used for Serverworks and SIS.

If ata_sata_phy_reset() failed and ata_generic_reset() is not called, mark
channel as having no devices connected. This improves hot-unplug operation
on legacy-emulating SATA controllers.

Make hw.ata.ata_dma_check_80pin tunable affect not only device side, but
also controller side cable checks. Make respective sysctl writable.

PR: kern/143462

Add support for SATA part of Marvell 88SE912x controllers to ahci(4).
Limit early revisions from 6Gb/s to 3Gb/s by default, or they negotiate
only 1.5Gbps, when 3Gb/s devices connected.

Add dummy driver for PATA part of these controllers, preventing generic
driver attach them. It causes system freeze when SATA controller used after
PATA was touched.

MFp4:
Introduce ATA_CAM kernel option, turning ata(4) controller drivers into
cam(4) interface modules. When enabled, this options deprecates all ata(4)
peripheral drivers (ad, acd, ...) and interfaces and allows cam(4) drivers
(ada, cd, ...) and interfaces to be natively used instead.

As side effect of this, ata(4) mode setting code was completely rewritten
to make controller API more strict and permit above change. While doing
this, SATA revision was separated from PATA mode. It allows DMA-incapable
SATA devices to operate and makes hw.ata.atapi_dma tunable work again.

Also allow ata(4) controller drivers (except some specific or broken ones)
to handle larger data transfers. Previous constraint of 64K was artificial
and is not really required by PCI ATA BM specification or hardware.

Submitted by: nwitehorn (powerpc part)

Change the way in which AHCI+PATA combined controllers, such as JMicron
and Marvell handled. Instead of trying to attach two different drivers to
single device, wrapping each call, make one of them (atajmicron, atamarvell)
attach do device solely, but create child device for AHCI driver,
passing it all required resources. It is quite easy, as none of
resources are shared, except IRQ.

As result, it:
- makes drivers operation more independent and straitforward,
- allows to use new ahci(4) driver with such devices, adding support for
new features, such as PMP and NCQ, same time keeping legacy PATA support,
- will allow to just drop old ataahci driver, when it's time come.

Add support for SATA ports on SATA+PATA Marvell controllers.
These controllers provide combination of AHCI for SATA and legacy
PCI ATA for PATA. Use same solution as used for JMicron controllers.
Add IDs of Marvell 88SX6102, 88SX6111. 88SX6141 alike controllers

Allow newly added controllers to use full I/O sizes.

MFp4:
- Remove most of direct relations between ATA(4) peripherial and controller
levels. It makes logic more transparent and is a mandatory step to wrap
ATA(4) controller level into ATA-native CAM SIM.
- Tune AHCI and SATA2 SiI drivers memory allocation a bit to allow bigger
I/O transaction sizes without additional cost.

Add support for different request block format used by Gen-IIe Marvell SATA.
This adds support for Marvell 6042/7042 chips and Adaptec 1430SA controller.

- Add missing bus_dmamap_sync(9) calls for the work DMA map. Previously
the work area was totally unsynchronized which means this driver only
had a chance of working on x86 when no bounce buffers were involved,
which isn't that likely given that support for 64-bit DMA is currently
broken throughout ata(4).
- Add necessary little-endian conversion of accesses to the work area,
making this driver work on big-endian hosts. While at it, use the
alignment-agnostic byte order encoders in order to be on the safe side.
- Clear the reserved member of the SG list entries in order to be on the
safe side. [1]

Submitted by: yongari [1]
Reviewed by: yongari
MFC after: 3 days

Revert previous commit and add myself to the list of people who should
know better than to commit with a cat in the area.

Add necessary include.

Fix Marvel SATA controllers operation, broken by rev. 188765,
by using uninitialized variable.

Tested by: Chris Hedley
Approved by: re (kensmith)

MFp4:
Reduce default PCI ATA drivers priorities from absolute to default,
to allow them been overriden. It was so before modularization.

Integrate user/mav/ata branch:

Add ch_suspend/ch_resume methods for PCI controllers and implement them
for AHCI. Refactor AHCI channel initialization according to it.

Fix Port Multipliers operation. It is far from perfect yet, but works now.
Tested with JMicron JMB363 AHCI + SiI 3726 PMP pair.
Previous version was also tested with SiI 4726 PMP.

Hardware sponsored by: Vitsch Electronics / VEHosting.nl

Remove the local management of INTx as this is now taken care of by pci.

Reviewed by: jhb
MFC after: 3 days

Quite mechanical ch_detach implementations for all atapci subdrivers.
Some dmainit call fixes for previous commit.

As soon as they called in only same one place (ata_pcichannel_attach()),
join allocate() and dmainit() atapci subdriver's channel initialization
methods into single ch_attach() method.

As opposite to ch_attach() add new ch_detach() method to deallocate/disable
channel.

Add support for Marvell PATA M88SX6121.

PR: 129154
Submitted by: João Barros <joao.barros at gmail.com>
MFC after: 1 month

- For chipsets that can't do 64k transfers, fall back to 32k transfers
(still a power of 2) rather than 63k transfers. Even with 63k transfers
some machines (such as Dell SC1435's) were experiencing chronic data
corruption.
- Use the MIO method to talk to the Serverworks HT1000_S1 SATA controller
like all the other SATA controllers rather than the compat PATA
method. This lets the controller see all 4 SATA ports and also
matches the behavior of the Linux driver.

Silence from: sos
MFC after: 3 days

This is the roumored ATA modulerisation works, and it needs a little explanation.

If you just config KERNEL as usual there should be no apparent changes, you'll get all chipset support code compiled in.

However there is now a way to only compile in code for chipsets needed on a pr vendor basis. ATA now has the following "device" entries:

atacore: ATA core functionality, always needed for any ATA setup

atacard: CARDBUS support
atacbus: PC98 cbus support
ataisa: ISA bus support
atapci: PCI bus support only generic chipset support.

ataahci: AHCI support, also pulled in by some vendor modules.

ataacard, ataacerlabs, ataadaptec, ataamd, ataati, atacenatek, atacypress, atacyrix, atahighpoint, ataintel, ataite, atajmicron, atamarvell, atamicron, atanational, atanetcell, atanvidia, atapromise, ataserverworks, atasiliconimage, atasis, atavia; Vendor support, ie atavia for VIA chipsets

atadisk: ATA disk driver
ataraid: ATA softraid driver

atapicd: ATAPI cd/dvd driver
atapifd: ATAPI floppy/flashdisk driver
atapist: ATAPI tape driver

atausb: ATA<>USB bridge
atapicam: ATA<>CAM bridge

This makes it possible to config a kernel with just VIA chipset support by having the following ATA lines in the kernel config file:

device atacore
device atapci
device atavia

And then you need the atadisk, atapicd etc lines in there just as usual.

If you use ATA as modules loaded at boot there is few changes except the rename of the "ata" module to "atacore", things looks just as usual.
However under atapci you now have a whole bunch of vendor specific drivers, that you can kldload individually depending on you needs. Drivers have the same names as used in the kernel config explained above.