Copy stable/11@r303970 to releng/11.0 as part of the 11.0-RELEASE
cycle.

Prune svn:mergeinfo from the new branch, and rename it to RC1.

Update __FreeBSD_version.

Use the quarterly branch for the default FreeBSD.conf pkg(8) repo and
the dvd1.iso packages population.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Copy head@r302406 to stable/11 as part of the 11.0-RELEASE cycle.
Prune svn:mergeinfo from the new branch, as nothing has been merged
here.

Additional commits post-branch will follow.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Add initial support for the AR9485 CUS198 / CUS230 variants.

These variants have a few differences from the default AR9485 NIC,
namely:

* a non-default antenna switch config;
* slightly different RX gain table setup;
* an external XLNA hooked up to a GPIO pin;
* (and not yet done) RSSI threshold differences when
doing slow diversity.

To make this possible:

* Add the PCI device list from Linux ath9k, complete with vendor and
sub-vendor IDs for various things to be enabled;
* .. and until FreeBSD learns about a PCI device list like this,
write a search function inspired by the USB device enumeration code;
* add HAL_OPS_CONFIG to the HAL attach methods; the HAL can use this
to initialise its local driver parameters upon attach;
* copy these parameters over in the AR9300 HAL;
* don't default to override the antenna switch - only do it for
the chips that require it;
* I brought over ar9300_attenuation_apply() from ath9k which is cleaner
and easier to read for this particular NIC.

This is a work in progress. I'm worried that there's some post-AR9380
NIC out there which doesn't work without the antenna override set as
I currently haven't implemented bluetooth coexistence for the AR9380
and later HAL. But I'd rather have this code in the tree and fix it
up before 11.0-RELEASE happens versus having a set of newer NICs
in laptops be effectively RX deaf.

Tested:

* AR9380 (STA)
* AR9485 CUS198 (STA)

Obtained from: Qualcomm Atheros, Linux ath9k

Fix a corner case in the HAL debugging changes, where ah was NULL.

Although I tried to fix this earlier by introducing HALDEBUG_G(), it
turns out there seem to be other cases where the pointer value is still
NULL.

* Fix DO_HALDEBUG() and the HALDEBUG macro to check whether ah is NULL
before deferencing it
* Remove HALDEBUG_G() as it's no longer needed

This is hopefully a merge candidate for 9.0-RELEASE as enabling
debugging at startup could result in a kernel panic.

Re-introduce a global ath_hal_debug again for now, whilst I figure out what
to do about the few cases where the HAL state isn't available (regdomain)
or isn't yet setup (probe/attach.)

The global ath_hal_debug now affects all instances of the HAL.

This also restores the ability for probe/attach debugging to work; as
the sysctl tree may not be attached at that point. Users can just set
the global "hw.ath.hal.debug" to a suitable value to enable probe/attach
related debugging.

Include the initial support for external EEPROMs.

The AR9100 at least doesn't have an external serial EEPROM
attached to the MAC; it instead stores the calibration data
in the normal system flash.

I believe earlier parts can do something similar but I haven't
experienced it first-hand.

This commit introduces an eepromdata pointer into the API but
doesn't at all commit to using it. A future commit will
include the glue needed to allow the AR9100 support code
to use this data pointer as the EEPROM.

Recognize AR5212_AR2317_REV2 in ar5312Probe()

Submitted by: Pavel Roskin <proski@gnu.org>

fix ini setup

Submitted by: Jiri Fojtasek <jiri.fojtasek@hlohovec.net>

remove duplicate case

Obtained from: netbsd

import ath hal

add chip+rf names for debug msgs, showing compiled-in support, etc.

Replace most compile-time support options with linker sets for
chip and RF backend support:
o add OS_DATA_SET and OS_SET_DECLARE os requirements for setting
up linker sets
o add AH_CHIP macro for registering chip support (e.g. 5210)
o add AH_RF macro for registering RF support (e.g. 2413); note
this isn't required for single chip solutions where there's no
ambiguity (e.g. 5416/9160+2133) but for 5212 class parts it's
required because of the multi-chip solutions
o remove all uses of AH_SUPPORT_AR5210, AH_SUPPORT_AR5211, AH_SUPPORT_5212,
and AH_SUPPORT_AR9160; still need AH_SUPPORT_AR5416 to enable the 11n
descriptor formats and 5312 support is presently broken
o remove all uses of AH_SUPPORT_2133, AH_SUPPORT_2413, AH_SUPPORT_5111,
AH_SUPPORT_5112, AH_SUPPORT_2417, AH_SUPPORT_2425, and AH_SUPPORT_5413;
5312-related support still requires fixup

Remaining issues:
o fixup SoC attach
o ath_hal_attach uses a hack to probe w/o access to the vendorid
o fallback handling of parts w/o a macrev needs to be restored

Update to later code from my repository:
o many bug fixes
o add new periodic calibration api
o break up 5416 periodic calibration code in preparation for 928x
o move get noise floor to rf backends
o 5416-specific ani (still disabled)
o modularize 5210 eeprom format a la other eeprom formats
o start cleaning up regdomain code
o prepare for proper 1/2 and 1/4 width channel support
o bring back 900MHz card support
o clean up 5212 rf version handling
o add 1/2 and 1/4 width channel support for 5212 parts
o split 5212 rfgain handling out
o improve ani debugging
o add AH_USE_INIPDGAIN compile option
o purge a bunch of dead 5212 state
o add 1/2 and 1/4 rate modes
o remove HAL_CAP_CHAN_HALFRATE and HAL_CAP_CHAN_QUARTERRATE; the
same info can now be deduced from the set of supported modes

virgin import of ath hal