Copy stable/11@r303970 to releng/11.0 as part of the 11.0-RELEASE
cycle.

Prune svn:mergeinfo from the new branch, and rename it to RC1.

Update __FreeBSD_version.

Use the quarterly branch for the default FreeBSD.conf pkg(8) repo and
the dvd1.iso packages population.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Copy head@r302406 to stable/11 as part of the 11.0-RELEASE cycle.
Prune svn:mergeinfo from the new branch, as nothing has been merged
here.

Additional commits post-branch will follow.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Grammar fix: s/NIC's/NICs/

MFC after: 3 days

Hook up the five gpio pins on the Avila board to the gpio framework. There are
actually 16 I/O lines but the other ones are used for system devices and
interrupts.

The IXP4XX platform can set interrupts on these pins for
high/low/rising/falling/transitional but this is not implemented yet.

The Cambria has the same interface but as all the pins are assigned to system
functions the gpio header is toggled via a PLD on the i2c bus and is not
supported by this commit.

o remove hack to write UUE+RTOIE in the uart's IER; force them with hints
o honor hints for the rclk

- Rename ds1672 and ds133x devices to "ds1672_rtc" and "ds133x_rtc"
respectivly. This will allow one to have a kernel with both devices
present and use it for multiple boards with different types of RTC
sitting on a bus.

Discussed with: imp

- Give a warning and start the oscillator if it was not previously
runned.
- Rename ds1672 -> rtc to follow the other drivers.
- Refactor/simplify the code a bit.

MFC after: 2 weeks

Add support for the StrataFlash on 2348 boards:
o add bus shim for cfi driver
o add static mapping for CS0 (we map all 16M as the cfi driver doesn't
support demand mapping)

Note this needs some tweaking to work for 2358 boards which is why the
CAMBRIA config is not touched.

Merge support for Gateworks Cambria boards:
o add support for IXP435 cpu's (e.g. 64 irq's)
o add support for Cambria-specific devices: npe, led's (front panel and
octal latch), ehci, mcu, ide cf
o redo memory mapping for xscale/ixp4xx boards: previously memory
was assumed aliased to 0x10000000 but this appears to be true only
for ixp425 systems and breaks operation on others; rework so memory
is assumed to start at 0
o rework NPE configuration support to use NPE id's instead of port #'s;
these changes also rename the associated MAC's to follow the NPE's
they are attached to
o update npe firmware to latest rev (same license) and update default fw
imageid's to match; in particular this adds NPE-A and crypto support
o re-style NPE fw handling code and add a console msg identifying the
attributes of the loaded fw
o fix numerous problems with handling failures during npe setup
o fix npe rx q setup; need to spin waiting for mailbox responses during
early boot stages as qmgr interrupts are not delivered; this fixes
the problem where all 8 traffic classifications were not tied to the
rx q (and eliminates the console msg "remember to fix rx q setup")
o add DELAY to npe MII wait logic for IXP435
o strip down builtin phys->virt address translation table in resource
handling to just those resources that require it and add a console msg
to alert people when this (kludge) table needs to be extended
o purge a bunch of dead netbsd-ism's
o cleanup avila led driver
o add Cambria support to boot2 and rework code for better multi-board support

Notes:
1. NPE-A doesn't work and causes NPE-C to stop working; it is disabled
in the hints
2. USB isn't working yet; controller communicates ok but device
discovery fails
3. Cambria support must be configured separately from IXP425 boards;
multi-board support is TBD

Sponsored by: Hobnob, Gateworks (board donation)
Reviewed by: imp

add hints to specify how NPE ports are mapped to MAC+PHY; these
could be commented out as they just duplicate the defaults that
are built into the code

Reviewed by: imp
MFC after: 1 week

Remove the hardcoded IXP425_UART?_VBASE values in the
uart_ixp425_probe() and uart_cpu_getdev(). Change
uart_cpu_getdev() to use hints to find the console.

Reviewed by: marcel

o add hints for avila boards; brings back i2c devices lost when iicbus
started using hints instead of wired down device enumeration
o add usb commented out; will enable when support works

MFC after: 1 month