| #
330233 |
|
01-Mar-2018 |
eadler |
MFC r324570,r324580:
[net80211] begin handling multiple hardware decap'ed A-MSDU in the RX path.
The duplicate detection code currently expects A-MSDU frames to be encaped -
they're decap'ed /after/ duplicate detection.
However for ath10k (and iwm hardware later on) the firmware supports
doing A-MSDU decap in hardware - which shows up as multiple frames with
the same sequence number and IV.
This is the first part of decap handling - if we see a stretch of A-MSDU
frames from the driver with the MORE bit set, then don't treat them
as duplicates.
This isn't 100% complete as crypto sequence number handling and "A-MSDU in
A-MPDU" needs handling, but it's a start.
This should be a glorified no-op for everyone. Please tell me if it isn't.
|
| #
283535 |
|
25-May-2015 |
adrian |
Begin plumbing ieee80211_rx_stats through the receive path.
Smart NICs with firmware (eg wpi, iwn, the new atheros parts, the intel 7260
series, etc) support doing a lot of things in firmware. This includes but
isn't limited to things like scanning, sending probe requests and receiving
probe responses. However, net80211 doesn't know about any of this - it still
drives the whole scan/probe infrastructure itself.
In order to move towards suppoting smart NICs, the receive path needs to
know about the channel/details for each received packet. In at least
the iwn and 7260 firmware (and I believe wpi, but I haven't tried it yet)
it will do the scanning, power-save and off-channel buffering for you -
all you need to do is handle receiving beacons and probe responses on
channels that aren't what you're currently on. However the whole receive
path is peppered with ic->ic_curchan and manual scan/powersave handling.
The beacon parsing code also checks ic->ic_curchan to determine if the
received beacon is on the correct channel or not.[1]
So:
* add freq/ieee values to ieee80211_rx_stats;
* change ieee80211_parse_beacon() to accept the 'current' channel
as an argument;
* modify the iv_input() and iv_recv_mgmt() methods to include the rx_stats;
* add a new method - ieee80211_lookup_channel_rxstats() - that looks up
a channel based on the contents of ieee80211_rx_stats;
* if it exists, use it in the mgmt path to switch the current channel
(which still defaults to ic->ic_curchan) over to something determined
by rx_stats.
This is enough to kick-start scan offload support in the Intel 7260
driver that Rui/I are working on. It also is a good start for scan
offload support for a handful of existing NICs (wpi, iwn, some USB
parts) and it'll very likely dramatically improve stability/performance
there. It's not the whole thing - notably, we don't need to do powersave,
we should not scan all channels, and we should leave probe request sending
to the firmware and not do it ourselves. But, this allows for continued
development on the above features whilst actually having a somewhat
working NIC.
TODO:
* Finish tidying up how the net80211 input path works.
Right now ieee80211_input / ieee80211_input_all act as the top-level
that everything feeds into; it should change so the MIMO input routines
are those and the legacy routines are phased out.
* The band selection should be done by the driver, not by the net80211
layer.
* ieee80211_lookup_channel_rxstats() only determines 11b or 11g channels
for now - this is enough for scanning, but not 100% true in all cases.
If we ever need to handle off-channel scan support for things like
static-40MHz or static-80MHz, or turbo-G, or half/quarter rates,
then we should extend this.
[1] This is a side effect of frequency-hopping and CCK modes - you
can receive beacons when you think you're on a different channel.
In particular, CCK (which is used by the low 11b rates, eg beacons!)
is decodable from adjacent channels - just at a low SNR.
FH is a side effect of having the hardware/firmware do the frequency
hopping - it may pick up beacons transmitted from other FH networks
that are in a different phase of hopping frequencies.
|
| #
282820 |
|
12-May-2015 |
adrian |
Do not check sequence number for QoS Null frames; set it for generated QoS Null
frames to 0
From IEEE Std. 802.11-2012, 8.3.2.1 "Data frame format", p. 415 (513):
"The Sequence Control field for QoS (+)Null frames is ignored by the receiver
upon reception."
At this moment, any <mode>_input() function interprets them as regular QoS data
frames with TID = 0. As a result, stations, that use another TX sequence for
QoS Null frames (e.g. wpi(4), where (QoS) Null frames are generated by the
firmware), may experience significant packet loss with any other NIC in hostap
mode.
Tested:
* wpi(4) (author)
* iwn(4) - Intel 5100, STA mode (me)
PR: kern/200128
Submitted by: Andriy Voskoboinyk <s3erios@gmail.com>
|
| #
221418 |
|
04-May-2011 |
adrian |
Fix some corner cases in the net80211 sequence number retransmission
handling.
The current sequence number code does a few things incorrectly:
* It didn't try eliminating duplications from HT nodes. I guess it's assumed
that out of order / retransmission handling would be handled by the AMPDU RX
routines. If a HT node isn't doing AMPDU RX, then retransmissions need to
be eliminated. Since most of my debugging is based on this (as AMPDU TX
software packet aggregation isn't yet handled), handle this corner case.
* When a sequence number of 4095 was received, any subsequent sequence number
is going to be (by definition) less than 4095. So if the following sequence
number (0) doesn't initially occur and the retransmit is received, it's
incorrectly eliminated by the IEEE80211_FC1_RETRY && SEQ_LEQ() check.
Try to handle this better.
This almost completely eliminates out of order TCP statistics showing up during
iperf testing for the 11a, 11g and non-aggregate 11n AMPDU RX case. The only
other packet loss conditions leading to this are due to baseband resets or
heavy interference.
|
| #
186904 |
|
08-Jan-2009 |
sam |
TDMA support for long distance point-to-point links using ath devices:
o add net80211 support for a tdma vap that is built on top of the
existing adhoc-demo support
o add tdma scheduling of frame transmission to the ath driver; it's
conceivable other devices might be capable of this too in which case
they can make use of the 802.11 protocol additions etc.
o add minor bits to user tools that need to know: ifconfig to setup and
configure, new statistics in athstats, and new debug mask bits
While the architecture can support >2 slots in a TDMA BSS the current
design is intended (and tested) for only 2 slots.
Sponsored by: Intel
|