Revert r330897:

This was intended to be a non-functional change. It wasn't. The commit
message was thus wrong. In addition it broke arm, and merged crypto
related code.

Revert with prejudice.

This revert skips files touched in r316370 since that commit was since
MFCed. This revert also skips files that require $FreeBSD$ property
changes.

Thank you to those who helped me get out of this mess including but not
limited to gonzo, kevans, rgrimes.

Requested by: gjb (re)

Partial merge of the SPDX changes

These changes are incomplete but are making it difficult
to determine what other changes can/should be merged.

No objections from: pfg

MFC r307518:
Fix device delete child function.

When detaching device trees parent devices must be detached prior to
detaching its children. This is because parent devices can have
pointers to the child devices in their softcs which are not
invalidated by device_delete_child(). This can cause use after free
issues and panic().

Device drivers implementing trees, must ensure its detach function
detaches or deletes all its children before returning.

While at it remove now redundant device_detach() calls before
device_delete_child() and device_delete_children(), mostly in
the USB controller drivers.

Tested by: Jan Henrik Sylvester <me@janh.de>
Reviewed by: jhb
Differential Revision: https://reviews.freebsd.org/D8070

Copy head@r302406 to stable/11 as part of the 11.0-RELEASE cycle.
Prune svn:mergeinfo from the new branch, as nothing has been merged
here.

Additional commits post-branch will follow.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

EHCI: Make core reset and port speed reading more generic.

Use driver settable callbacks for handling of:
- core post reset
- reading actual port speed

Typically, OTG enabled EHCI cores wants setting of USBMODE register,
but this register is not defined in EHCI specification and different
cores can have it on different offset.

Also, for cores with TT extension, actual port speed must be determinable.
But again, EHCI specification not covers this so this patch provides
function for two most common variant of speed bits layout.

Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D5088

Add initial support for the QCA953x ("Honeybee") from Qualcomm Atheros.

The QCA953x SoC is an integrated 2x2 2GHz 11n + MIPS24k core, with
a 5 port FE switch, gige WAN port, and all the same stuff you'd find on
its predecessor - the AR9331.

However, buried deep in here somewhere is also a PCIe EP/RC for various
applications and some other weird bits I don't yet know about.

This is enough to get the reference board up and booting. I haven't yet
had it pass lots of packets - I need to finalise the ethernet switch
bits and the GMAC configuration (ie, how the ethernet ports and switch
are wired up) and I'll bring that in when I commit the base configuration
files to use the thing.

The wifi stuff will come much later. I have to port that support from
Linux ath9k and extend our vendor HAL to support it.

The reference board (AP143) comes with 32MB RAM and 4MB flash, so in order
to use it I need to get USB working fully so I can run root from there.

Thankyou to Qualcomm Atheros for access to the reference design board.

Details:

* Add register definitions from openwrt;
* It looks like a QCA955x but shrunk down to a QCA933x footprint, so
use the QCA955x bits and fix up the clock detection code to do the
QCA953x bits (they're very subtly different);
* Teach GPIO about it;
* Teach EHCI about it;
* Teach if_arge about it;
* Teach the CPU detection code about it.

Tested:

* AP143, QCA9533v2 SoC

Obtained from: Linux, Linux OpenWRT

Reshuffle all of the DDR flush operations into a single switch/mux,
and start teaching subsystems about it.

The Atheros MIPS platforms don't guarantee any kind of FIFO consistency
with interrupts in hardware. So software needs to do a flush when it
receives an interrupt and before it calls the interrupt handler.

There are new ones for the QCA934x and QCA955x, so do a few things:

* Get rid of the individual ones (for ethernet and IP2);
* Create a mux and enum listing all the variations on DDR flushes;
* replace the uses of IP2 with the relevant one (which will typically
be "PCI" here);
* call the USB DDR flush before calling the real USB interrupt handlers;
* call the ethernet one upon receiving an interrupt that's for us,
rather than never calling it during operation.

Tested:

* QCA9558 (TP-Link archer c7 v2)
* AR9331 (Carambola 2)

TODO:

* PCI, USB, ethernet, etc need to do a double-check to see if the
interrupt was truely for them before doing the DDR. For now I
prefer "correct" over "fast".

[QCA955x] make the USB EHCI interrupts shareable.

There's two EHCI controllers in the QCA955x SoCs - they have different
interrupts available via various demux registers, but they both tie to
IP3.

So for now, allow them to be sharable so they can hang off of IP3.

Add QCA955x support to the EHCI setup path.

Tested:

* QCA AP135 development board, USB rootfs.

Add 64-bit DMA support in the XHCI controller driver.
- Fix some comments and whitespace while at it.

MFC after: 1 month
Submitted by: marius@

Add the USB EHCI flags required for the post-AR71xx devices.

Tested:

* DB120, AR9344

Devices that rely on hints or identify routines for discovery need to
return BUS_PROBE_NOWILDCARD from their probe routines to avoid claiming
wildcard devices on their parent bus. Do a sweep through the MIPS tree.

MFC after: 2 weeks

Fix AR933x USB support - this needs the same controller initialisation
as the AR7242.

Tested:

* Atheros AP121, AR9331
* ZyDas wifi device, and 64MB (yes, ew) USB flash storage

Implement better support for USB controller suspend and resume.

This patch should remove the need for kldunload of USB
controller drivers at suspend and kldload of USB controller
drivers at resume.

This patch also fixes some build issues in avr32dci.c

MFC after: 2 weeks

Rename device_delete_all_children() into device_delete_children().

Suggested by: jhb @ and marius @
MFC after: 1 week

- There's no need to overwrite the default device method with the default
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.

We don't need to call EOWRITE4(sc, EHCI_USBINTR, 0) directly from each EHCI
bus driver at detach, hence ehci_detach() does exactly this since r199718.

Submitted by: Luiz Otavio O Souza
MFC after: 7 days
Approved by: thompsa (mentor)

- Correct EHCI interrupt disabling at detach.

Submitted by: Luiz Otavio O Souza
MFC after: 7 days
Approved by: thompsa (mentor)

Add in some missing flags in the EHCI initialisation code,
needed to get USB working on the AR913x/AR724x.

Add some missing flags needed for AR913x/AR724x USB to correctly operate.

The AR913x/AR724x USB lives at a different offset to the AR71xx
USB, so this needs to be either adjusted for in a subsequent
commit, or updated in hints for kernels compiled for those
platforms.

Submitted by: Luiz Otavio O Souzau <loos.br@gmail.com>

Set the svn:eol-style = native and svn:mime-type = text/plain
properties on all files in this tree.

Submitted by: rpaulo@

Place proper svn:keywords tag on all these files. They were created
somehow without them on projects/mips, and that mistake was propigated
over to head.

Submitted by: rpaulo@

Merge from projects/mips to head by hand:

Merge support files for the Atheros AR71xx (and soon AR9xxx)
processors, except files from sys/conf and sys/mips/conf. This work
was done primarily by Olecksandr Tymoshenko and works on the
RouterStation and RouterStation PRO. Other AR71xx-based boards have
been reported as working as well (RouterBoard, for example).

- include register definitions for respective controllers

- Remove flags accidently brought by dumb cut'n'paste coding

- Make USB part of AR71XX kernel buildable again

- Remove garbage debug output
- ar71xx_bus_space_reversed is bus_space_tag_t, use it this way

- Add EHCI controller driver for AR71XX-based boards.