| #
330307 |
|
03-Mar-2018 |
np |
MFC r319506, r319872, r321063, r321103, r321179, r321390, r321435,
r321582, r321671, r322014, r322034, r322055, r322123, r322167, r322425,
r322549, r322914, r322960, r322962, r322964, r322985, r322990, r323006,
r323026, r323041, r323069, r323078, r323343, r323514, r323520, r324296,
r324379, r324386, r324443, r324945, r325596, r325680, r325880,
r325883-r325884, r325961, r326026, r326042, r327062, r327093, r327332,
r327528, r328420, and r328423.
r319506:
cxgbe(4): Update the statistics for compound tx work requests once per
work request, not once per frame.
r319872:
cxgbe(4): Do not request an FEC setting that the port does not support.
r321063:
cxgbe(4): Various link/media related improvements.
- Deal with changes to port_type, and not just port_mod when a
transceiver is changed. This fixes hot swapping of transceivers of
different types (QSFP+ or QSA or QSFP28 in a QSFP28 port, SFP+ or
SFP28 in a SFP28 port, etc.).
- Always refresh media information for ifconfig if the port is down.
The firmware does not generate tranceiver-change interrupts unless at
least one VI is enabled on the physical port. Before this change
ifconfig diplayed potentially stale information for ports that were
administratively down.
- Always recalculate and reapply L1 config on a transceiver change.
- Display PAUSE settings in ifconfig. The driver sysctls for this
continue to work as well.
r321103:
cxgbe(4): New ioctls to flash bootrom and boot config to the card.
r321179:
cxgbe/t4_tom: Log more details about the newly ESTABLISHED tid to the
trace buffer.
r321390:
cxgbe(4): Install the firmware bundled with the driver to the card if it
doesn't seem to have one. This lets the driver recover automatically
from incomplete firmware upgrades (panic, reboot, power loss, etc. in
the middle of an upgrade).
r321435:
cxgbe(4): Display some more TOE parameters related to retransmission
and keepalive in the sysctl MIB. Provide tunables to change some of
these parameters. These are supposed to be setup by the firmware so
these tunables are for experimentation only.
r321582:
cxgbe(4): Some updates to the common code.
- Updated register ranges.
- Helper routines for access to TP registers.
- Updated routine to read flash parameters.
r321671:
cxgbe/iw_cxgbe: Log the end point's history and flags to the trace
buffer just before it's freed.
r322014:
cxgbe(4): Initial import of the "collect" component of Chelsio unified
debug (cudbg) code, hooked up to the main driver via an ioctl.
The ioctl can be used to collect the chip's internal state in a
compressed dump file. These dumps can be decoded with the "view"
component of cudbg.
r322034:
cxgbe(4): Always use the first and not the last virtual interface
associated with a port in begin_synchronized_op.
r322055:
cxgbe(4): Allow the TOE timer tunables to be set with microsecond
precision. These timers are already displayed in microseconds in the
sysctl MIB. Add variables to track these tunables while here.
r322123:
cxgbe(4): Avoid a NULL dereference that would occur during module unload
if there were problems earlier during attach.
r322167:
cxgbe(4): Add the T6 and T5 Unified Wire configuration files to the
kernel, just like for T4, when the driver is compiled into the kernel.
r322425:
cxgbe(4): Save the last reported link parameters and compare them with
the current state to determine whether to generate a link-state change
notification. This fixes a bug introduced in r321063 that caused the
driver to sometimes skip these notifications.
r322549:
cxgbe/t4_tom: Use correct name for the ISS-valid bit in options2.
r322914:
cxgbe(4): Dump the mailbox contents in the same format as CH_DUMP_MBOX.
r322960:
cxgbe(4): Verify that the driver accesses the firmware mailbox in a
thread-safe manner.
r322962:
cxgbe(4): Remove write only variable from t4_port_init.
r322964:
cxgbe(4): vi_mac_funcs should include the base Ethernet function. It is
already used in the driver as if it does.
r322985:
cxgbe(4): Maintain one ifmedia per physical port instead of one per
Virtual Interface (VI). All autonomous VIs that share a port share the
same media.
r322990:
cxgbe(4): Do not access the mailbox without appropriate locks while
creating hardware VIs.
This fixes a bad race on systems with hw.cxgbe.num_vis > 1.
r323006:
cxgbe(4): Update T6/T5/T4 firmwares to 1.16.59.0.
r323026:
cxgbe(4): Zero out the memory allocated for the debug dump.
cudbg_collect seems to expect it this way.
r323041:
cxgbe(4): Add two new debug flags -- one to allow manual firmware
install after full initialization, and another to disable the TCB
cache (T6+). The latter works as a tunable only.
Note that debug_flags are for debugging only and should not be set
normally.
r323069:
cxgbe/t4_tom: Add a knob to select the congestion control algorigthm
used by the TOE hardware for fully offloaded connections. The knob
affects new connections only.
r323078:
cxgbe/t4_tom: There may not be a tid to update if the connection isn't
established.
r323343:
cxgbe(4): Fix a couple of problems in the sge_wrq data path.
- start_wrq_wr must not drain the wr_list if there are incomplete_wrs
pending. This can happen when a t4_wrq_tx runs between two
start_wrq_wr.
- commit_wrq_wr must examine the cookie's pidx and ndesc with the
queue's lock held. Otherwise there is a bad race when incomplete WRs
are being completed and commit_wrq_wr for the WR that is ahead in the
queue updates the next incomplete WR's cookie's pidx/ndesc but the
commit_wrq_wr for the second one is using stale values that it read
without the lock.
r323514:
cxgbetool(8): mode must be specified when creating the dump file.
r323520:
cxgbe(4): Ignore capabilities that depend on TOE when the firmware
reports TOE is not available.
r324296:
cxgbe(4): Provide knobs to set the holdoff parameters of TOE rx queues
separately from NIC rx queues instead of using the same parameters for
both types of queues.
r324379:
cxgbetool(8): Do not create a large file devoid of useful content when
the dumpstate ioctl fails. Make the file world-readable while here.
r324386:
cxgbe(4): Update T6, T5, and T4 firmwares to 1.16.63.0.
r324443:
cxgbetool(8): Do not close uninitialized fd on malloc failure.
r324945:
cxgbe(4): Read the MPS buffer group map from the firmware as it could be
different from hardware defaults. The congestion channel map, which is
still fixed, needs to be tracked separately now. Change the congestion
setting for TOE rx queues to match the drivers on other OSes while here.
r325596:
cxgbe(4): Do not request settings not supported by the port.
r325680:
cxgbe(4): Excluce mdi from the check against port capabilities.
r325880:
cxgbe(4): Combine all _10g and _1g tunables and drop the suffix from
their names. The finer-grained knobs weren't practically useful.
r325883:
cxgbe(4): Sanitize t4_num_vis during MOD_LOAD like all other t4_*
tunables. Add num_vis to the intrs_and_queues structure as it affects
the number of interrupts requested and queues created. In future
cfg_itype_and_nqueues might lower it incrementally instead of going
straight to 1 when enough interrupts aren't available.
r325884:
cxgbe(4): Remove rsrv_noflowq from intrs_and_queues structure as it does
not influence or get affected by the number of interrupts or queues.
r325961:
cxgbe(4): Add core Vdd to the sysctl MIB.
r326026:
cxgbe(4): Add a custom board to the device id list.
r326042:
cxgbe(4): Fix unsafe mailbox access in cudbg.
r327062:
cxgbe(4): Read the MFG diags version from the VPD and make it available
in the sysctl MIB.
r327093:
cxgbe(4): Do not forward interrupts to queues with freelists. This
leaves the firmware event queue (fwq) as the only queue that can take
interrupts for others.
This simplifies cfg_itype_and_nqueues and queue allocation in the driver
at the cost of a little (never?) used configuration. It also allows
service_iq to be split into two specialized variants in the future.
r327332:
cxgbe(4): Reduce duplication by consolidating minor variations of the
same code into a single routine.
r327528:
cxgbe(4): Add a knob to enable/disable PCIe relaxed ordering. Disable it by
default when running on Intel CPUs.
r328420:
cxgbe(4): Do not display harmless warning in non-debug builds.
r328423:
cxgbe(4): Accept old names of a couple of tunables.
Sponsored by: Chelsio Communications
|
| #
309560 |
|
05-Dec-2016 |
jhb |
MFC 305695,305696,305699,305702,305703,305713,305715,305827,305852,305906,
305908,306062,306063,306137,306138,306206,306216,306273,306295,306301,
306465,309302:
Add support for adapters using the Terminator T6 ASIC.
305695:
cxgbe(4): Set up fl_starve_threshold2 accurately for T6.
305696:
cxgbe(4): Use correct macro for header length with T6 ASICs. This
affects the transmit of the VF driver only.
305699:
cxgbe(4): Update the pad_boundary calculation for T6, which has a
different range of boundaries.
305702:
cxgbe(4): Use smaller min/max bursts for fl descriptors with a T6.
305703:
cxgbe(4): Deal with the slightly different SGE_STAT_CFG in T6.
305713:
cxgbe(4): Add support for additional port types and link speeds.
305715:
cxgbe(4): Catch up with the rename of tlscaps -> cryptocaps. TLS is one
of the capabilities of the crypto engine in T6.
305827:
cxgbe(4): Use the interface's viid to calculate the PF/VF/VFValid fields
to use in tx work requests.
305852:
cxgbe(4): Attach to cards with the Terminator 6 ASIC. T6 cards will
come up as 't6nex' nexus devices with 'cc' ports hanging off them.
The T6 firmware and configuration files will be added as soon as they
are released. For now the driver will try to work with whatever
firmware and configuration is on the card's flash.
305906:
cxgbe/t4_tom: The SMAC entry for a VI is at a different location in the T6.
305908:
cxgbe/t4_tom: Update the active/passive open code to support T6. Data
path works as-is.
306062:
cxgbe(4): Show wcwr_stats for T6 cards.
306063:
cxgbe(4): Setup congestion response for T6 rx queues.
306137:
cxgbetool: Add T6 support to the SGE context decoder.
306138:
Fix typo.
306206:
cxgbe(4): Catch up with the different layout of WHOAMI in T6.
Note that the code moved below t4_prep_adapter() as part of this change
because now it needs a working chip_id().
306216:
cxgbe(4): Fix the output of the "tids" sysctl on T6.
306273:
cxgbe(4): Fix netmap with T6, which doesn't encapsulate SGE_EGR_UPDATE
message inside a FW_MSG. The base NIC already deals with updates in
either form.
306295:
cxgbe(4): Support SIOGIFXMEDIA so that ifconfig displays correct media
for 25Gbps and 100Gbps ports. This should have been part of r305713,
which is when the driver first started reporting extended media types.
306301:
cxgbe(4): Use the port's top speed to figure out whether it is "high
speed" or not (for the purpose of calculating the number of queues etc.)
This does the right thing for 25Gbps and 100Gbps ports.
306465:
cxgbe(4): Claim the T6 -DBG card.
309302:
cxgbe(4): Include firmware for T6 cards in the driver. Update all
firmwares to 1.16.12.0.
Sponsored by: Chelsio Communications
|
| #
306664 |
|
03-Oct-2016 |
jhb |
MFC 303522,303647,303860,303880,304168,304169,304170,304479,304485,305549:
Chelsio T4/T5 VF driver.
303522:
Various fixes to the t4/5nex character device.
- Remove null open/close methods.
- Don't set d_flags to 0 explicitly.
- Remove t5_cdevsw as the .d_name member isn't really used and doesn't
warrant a separate cdevsw just for the name.
- Use ENOTTY as the error value for an unknown ioctl request.
- Use make_dev_s() to close race with setting si_drv1.
303647:
Store the offset of the KDOORBELL and GTS registers in the softc.
VF devices use a different register layout than PF devices. Storing
the offset in a value in the softc allows code to be shared between the
PF and VF drivers.
303860:
Reserve an adapter flag IS_VF to mark VF devices vs PF devices.
303880:
Track the base absolute ID of ingress and egress queues.
Use this to map an absolute queue ID to a logical queue ID in interrupt
handlers. For the regular cxgbe/cxl drivers this should be a no-op as
the base absolute ID should be zero. VF devices have a non-zero base
absolute ID and require this change. While here, export the absolute ID
of egress queues via a sysctl.
304168:
Make SGE parameter handling more VF-friendly.
Add fields to hold the SGE control register and free list buffer sizes to
the sge_params structure. Populate these new fields in
t4_init_sge_params() for PF devices and change t4_read_chip_settings() to
pull these values out of the params structure instead of reading
registers directly. This will permit t4_read_chip_settings() to be reused
for VF devices which cannot read SGE registers directly.
While here, move the call to t4_init_sge_params() to
get_params__post_init(). The VF driver will populate the SGE parameters
structure via a different method before calling t4_read_chip_settings().
304169:
Update mailbox writes to work with VF devices.
- Use alternate register locations for the data and control registers for
VFs.
- Do a dummy read to force the writes to the mailbox data registers to
post before the write to the control register on VFs.
- Do not check the PCI-e firmware register for errors on VFs.
304170:
Add support for register dumps on VF devices.
- Add handling of VF register sets to t4_get_regs_len() and t4_get_regs().
- While here, use t4_get_regs_len() in the ioctl handler for regdump
instead of inlining it.
304479:
Add structures for VF-specific adapter parameters.
While here, mark which parameters are PF-specific and which are
VF-specific.
304485:
Reorder sysctls so that nodes shared with the VF driver are added first.
This permits a single early return for VF devices in the routines that
add sysctl nodes.
305549:
Chelsio T4/T5 VF driver.
The cxgbev/cxlv driver supports Virtual Function devices for Chelsio
T4 and T4 adapters. The VF devices share most of their code with the
existing PF4 driver (cxgbe/cxl) and as such the VF device driver
currently depends on the PF4 driver.
Similar to the cxgbe/cxl drivers, the VF driver includes a t4vf/t5vf
PCI device driver that attaches to the VF device. It then creates
child cxgbev/cxlv devices representing ports assigned to the VF.
By default, the PF driver assigns a single port to each VF.
t4vf_hw.c contains VF-specific routines from the shared code used to
fetch VF-specific parameters from the firmware.
t4_vf.c contains the VF-specific PCI device driver and includes its
own attach routine.
VF devices are required to use a different firmware request when
transmitting packets (which in turn requires a different CPL message
to encapsulate messages). This alternate firmware request does not
permit chaining multiple packets in a single message, so each packet
results in a firmware request. In addition, the different CPL message
requires more detailed information when enabling hardware checksums,
so parse_pkt() on VF devices must examine L2 and L3 headers for all
packets (not just TSO packets) for VF devices. Finally, L2 checksums
on non-UDP/non-TCP packets do not work reliably (the firmware trashes
the IPv4 fragment field), so IPv4 checksums for such packets are
calculated in software.
Most of the other changes in the non-VF-specific code are to expose
various variables and functions private to the PF driver so that they
can be used by the VF driver.
Note that a limited subset of cxgbetool functions are supported on VF
devices including register dumps, scheduler classes, and clearing of
statistics. In addition, TOE is not supported on VF devices, only for
the PF interfaces.
Sponsored by: Chelsio Communications
|