Revert r330897:

This was intended to be a non-functional change. It wasn't. The commit
message was thus wrong. In addition it broke arm, and merged crypto
related code.

Revert with prejudice.

This revert skips files touched in r316370 since that commit was since
MFCed. This revert also skips files that require $FreeBSD$ property
changes.

Thank you to those who helped me get out of this mess including but not
limited to gonzo, kevans, rgrimes.

Requested by: gjb (re)

Partial merge of the SPDX changes

These changes are incomplete but are making it difficult
to determine what other changes can/should be merged.

No objections from: pfg

Copy head@r302406 to stable/11 as part of the 11.0-RELEASE cycle.
Prune svn:mergeinfo from the new branch, as nothing has been merged
here.

Additional commits post-branch will follow.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Fix tx pause quanta and timer calculations.

MFC after: 3 days

Always reset the XGMAC's XAUI PCS on a link up.

MFC after: 3 days

The 10GBASE-T card should use an IPG of 1. Also enable the check
for low power startup on this card.

cxgb(4) updates, including:
- support for the new Gen-2, BT, and LP-CR cards.
- T3 firmware 7.7.0
- shared "common code" updates.

Approved by: gnn (mentor)
Obtained from: Chelsio
MFC after: 1 month

Update the Chelsio driver to the latest bits from Chelsio

Firmware upgraded to 7.1.0 (from 5.0.0).
T3C EEPROM and SRAM added; Code to update eeprom/sram fixed.
fl_empty and rx_fifo_ovfl counters can be observed via sysctl.
Two new cxgbtool commands to get uP logic analyzer info and uP IOQs
Synced up with Chelsio's "common code" (as of 03/03/09)

Submitted by: Navdeep Parhar at Chelsio
Reviewed by: gnn
MFC after: 2 weeks

Bug fix from Chelsio which addresses the issue of the device resetting
when it sees only received packets. In some cases where a device only
recieves data it mistakenly thinks that its transmitting side is broken
and resets the device.

Obtained from: Chelsio Inc.
MFC after: 3 days

Update cxgb include paths to not require prefixing with dev/cxgb

Submitted by: Chelsio Inc.

Vendor fix for PHY problem.

Obtained from: Chelsio Inc.
MFC after: 3 days

import vendor fixes to cxgb

- update firmware to 5.0
- add support for T3C
- add DDP support (zero-copy receive)
- fix TOE transmit of large requests
- fix shutdown so that sockets don't remain in CLOSING state indefinitely
- register listeners when an interface is brought up after tom is loaded
- fix setting of multicast filter
- enable link at device attach
- exit tick handler if shutdown is in progress
- add helper for logging TCB
- add sysctls for dumping transmit queues

- note that TOE wxill not be MFC'd until after 7.0 has been finalized

MFC after: 3 days

- fix qset to port binding as a proper fix for the problems encountered on the 4-port
- fix the use after free seen when sending packets small enough to fit as an immediate
and bpf peers are present
- update to firmware rev 4.7 along with various small vendor fixes

Supported by: Chelsio
Approved by: re (blanket)
MFC after: 3 days

- integrate most recent changes from vendor branch and upgrade to firmware revision 4.5.5
- add filter support
- further improvements for T304
- recover gracefully from spurious immediate packets

Approved by: re(blanket)
Supported by: Chelsio
MFC after: 3 days

- import new common code for the T304
- update to firmware version 4.1.0

- switch over to standard method for initializing cdevs (contributed by scottl@)
- break out timer_reclaim_task to be per-port
- move msix teardown into separate function
- fix bus_setup_intr for msi-x for the multi-port case so that msi-x resources
are not corrupted on unload
- handle 10/100/1000 base-T media and auto negotiation
- bind qset to cpu even for singleq case
- white space cleanups
- remove recursive PORT_LOCK
- move mtu setting to separate function
- stop and re-init port when changing mtu
- replace all direct references to m_data with calls to mtod
- handle attach failure better by not trying to de-initialize
taskqueues when they have not been allocated
- no longer default to jumbo frames

Sponsored by: Chelsio
MFC after: 3 days

When building cxgb as a module make include paths relative to the driver's root.
This will make it possible to build the module out of tree against an older src tree.

MFC after: 3 days

(MFp4)
- upgrade to reflect state of 1.0.0.86
- move from firmware rev 3.2 to 4.0.0
- import driver bits for offload functionality
- remove binary distribution clause from top level files as it
runs counter to the intent of purely supporting the hardware

MFC after: 3 days

Synchronize with version 1.0.071 of Chelsio's common code
(with the notable exception of improvements for using multiple TX queues)

This adds support for the T3B2 ASIC rev

Obtained from: Chelsio
MFC after: 3 days

First of several commits for driver support for the Chelsio T3B 10 Gigabit
Ethernet adapter.

Reviewed by: scottl, sam

For those interested in the preliminary performance work see below.

Plots of mxge vs. cxgb running netpipe:

blocksize vs. bandwidth:
http://www.fsmware.com/chelsio.random/bsvsbw.gif

blocksize vs. RTT:
First of several commits for driver support for the Chelsio T3B 10 Gigabit
Ethernet adapter.

Reviewed by: scottl, sam

For those interested in the preliminary performance work see below.

Plots of mxge vs. cxgb running netpipe:

blocksize vs. bandwidth:
http://www.fsmware.com/chelsio.random/bsvsbw.gif

blocksize vs. RTT:
http://www.fsmware.com/chelsio.random/bsvstime.gif

blocksize vs. RTT for block sizes <= 10kb:
http://www.fsmware.com/chelsio.random/bsvstime_10kb.gif
http://www.fsmware.com/chelsio.random/bsvstime_10kb3.gif