| #
331722 |
|
29-Mar-2018 |
eadler |
Revert r330897:
This was intended to be a non-functional change. It wasn't. The commit
message was thus wrong. In addition it broke arm, and merged crypto
related code.
Revert with prejudice.
This revert skips files touched in r316370 since that commit was since
MFCed. This revert also skips files that require $FreeBSD$ property
changes.
Thank you to those who helped me get out of this mess including but not
limited to gonzo, kevans, rgrimes.
Requested by: gjb (re)
|
| #
330897 |
|
14-Mar-2018 |
eadler |
Partial merge of the SPDX changes
These changes are incomplete but are making it difficult
to determine what other changes can/should be merged.
No objections from: pfg
|
| #
302408 |
|
07-Jul-2016 |
gjb |
Copy head@r302406 to stable/11 as part of the 11.0-RELEASE cycle.
Prune svn:mergeinfo from the new branch, as nothing has been merged
here.
Additional commits post-branch will follow.
Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation |
| #
276959 |
|
11-Jan-2015 |
np |
cxgb: replace r273280 with a more comprehensive fix.
Poll for link state when the link is down, even for interrupt capable
PHYs.
Allow PHYs to report a dubious "partial" link. If this state is seen 3
consecutive times (each check is ~1s apart) then reset the PHY. This is
a workaround for a situation where repeatedly toggling the link from the
peer gets the AEL2005 PHY into a state where it never establishes a PCS
block lock even when everything is in order.
MFC after: 1 week
|
| #
197791 |
|
05-Oct-2009 |
np |
cxgb(4) updates, including:
- support for the new Gen-2, BT, and LP-CR cards.
- T3 firmware 7.7.0
- shared "common code" updates.
Approved by: gnn (mentor)
Obtained from: Chelsio
MFC after: 1 month
|
| #
183292 |
|
23-Sep-2008 |
kmacy |
Update cxgb include paths to not require prefixing with dev/cxgb
Submitted by: Chelsio Inc.
|
| #
180583 |
|
18-Jul-2008 |
kmacy |
import vendor fixes to cxgb
|
| #
176472 |
|
22-Feb-2008 |
kmacy |
- update firmware to 5.0
- add support for T3C
- add DDP support (zero-copy receive)
- fix TOE transmit of large requests
- fix shutdown so that sockets don't remain in CLOSING state indefinitely
- register listeners when an interface is brought up after tom is loaded
- fix setting of multicast filter
- enable link at device attach
- exit tick handler if shutdown is in progress
- add helper for logging TCB
- add sysctls for dumping transmit queues
- note that TOE wxill not be MFC'd until after 7.0 has been finalized
MFC after: 3 days
|
| #
171978 |
|
25-Aug-2007 |
kmacy |
Fixes for 4 port and small packet optimization
- remove cpl->iff panic - we can't know the port number from the rspq on the 4-port
- pick the ifnet based on the interface in the CPL header
- switch to using qset 0 for egress on the 4-port for now - may change
when we start using RSS
- move ether_ifdetach to before the port lock gets deinitialized to avoid
hang in the case where there are BPF peers (cxgb_ioctl is called indirectly
when BPF peers are present)
- don't call t3_mac_reset if multiport is set, this was causing tx errors
by misconfiguring the MAC on the 4-port
- change V_TXPKT_INTF to use txpkt_intf as the interfaces are not contiguous
- free the mbuf immediately in the case where the payload is small enough to be copied
into the rspq
- only update the coalesce timer if for a queue if packets were taken off of it
- add in missed 20ms DELAY in initializaton vsc8211
- prompt MFC as this only applies to the 4-port which is currently completely
broken - OK'd by kensmith
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 0 days
|
| #
170076 |
|
28-May-2007 |
kmacy |
When building cxgb as a module make include paths relative to the driver's root.
This will make it possible to build the module out of tree against an older src tree.
MFC after: 3 days
|
| #
167514 |
|
14-Mar-2007 |
kmacy |
First of several commits for driver support for the Chelsio T3B 10 Gigabit
Ethernet adapter.
Reviewed by: scottl, sam
For those interested in the preliminary performance work see below.
Plots of mxge vs. cxgb running netpipe:
blocksize vs. bandwidth:
http://www.fsmware.com/chelsio.random/bsvsbw.gif
blocksize vs. RTT:
First of several commits for driver support for the Chelsio T3B 10 Gigabit
Ethernet adapter.
Reviewed by: scottl, sam
For those interested in the preliminary performance work see below.
Plots of mxge vs. cxgb running netpipe:
blocksize vs. bandwidth:
http://www.fsmware.com/chelsio.random/bsvsbw.gif
blocksize vs. RTT:
http://www.fsmware.com/chelsio.random/bsvstime.gif
blocksize vs. RTT for block sizes <= 10kb:
http://www.fsmware.com/chelsio.random/bsvstime_10kb.gif
http://www.fsmware.com/chelsio.random/bsvstime_10kb3.gif
|