Copy head@r302406 to stable/11 as part of the 11.0-RELEASE cycle.
Prune svn:mergeinfo from the new branch, as nothing has been merged
here.

Additional commits post-branch will follow.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Remove comments about creating DMA tags as children of the DMA tags of their
parent bus where the code has now been modified to do so.

Reviewed by: scottl

add a newbus method for obtaining the bus's bus_dma_tag_t... This is
required by arches like sparc64 (not yet implemented) and sun4v where there
are seperate IOMMU's for each PCI bus... For all other arches, it will
end up returning NULL, which makes it a no-op...

Convert a few drivers (the ones we've been working w/ on sun4v) to the
new convection... Eventually all drivers will need to replace the parent
tag of NULL, w/ bus_get_dma_tag(dev), though dev is usually different for
each driver, and will require hand inspection...

Reviewed by: scottl (earlier version)

Start each of the license/copyright comments with /*-, minor shuffle of lines

Add an ISA attachement to the aic7xxx driver to handle 284X controllers.
The ISA probe uses an identify routine to probe all slot locations from
1 to 14 that do not conflict with other allocated resources. This required
making aic7770.c part of the driver core when compiled as a module.

aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
Use aic_scb_timer_start() consistently to start the watchdog timer.
This removes a few places that verbatum copied the code in
aic_scb_timer_start().

During recovery processing, allow commands to still be queued to
the controller. The only requirement we have is that our recovery
command be queued first - something the code already guaranteed.
The only other change required to make this work is to prevent
timers from being started for these newly queued commands.

Approved by: re

Convert callers to the new bus_alloc_resource_any(9) API.

Submitted by: Mark Santcroos <marks@ripe.net>
Reviewed by: imp, dfr, bde

ahc_eisa.c:
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.

aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.

aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.

aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.

aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.

aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.

aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.

ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.

aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.

ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.

Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.

ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.

Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.

aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.

aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.

physaddr -> busaddr

Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>

aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.

Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.

Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.

When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.

On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.

On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.

Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.

aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.

Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.

Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.

Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.

Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.

Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.

Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.

aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.

aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.

aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.

aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.

aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.

Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.

aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.

aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.

Use __FBSDID().
Also some minor style cleanups.

Mega busdma API commit.

Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma. At the moment, this is used for the
asynchronous busdma_swi and callback mechanism. Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg. dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create(). The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.

sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms. The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.

If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.

Reviewed by: tmm, gibbs

hc_eisa.c:
ahc_pci.c:
ahd_pci.c:
Don't bogusly use the BUS_DMA_ALLOCNOW flag in our psuedo
parent bus dma tag.

Convert the use of MAXBSIZE in the dma tag to more appropriate values.
Use BUS_SPACE_MAXSIZE_32BIT for the parent dma tags, and
(NSEGS - 1) * PAGE_SIZE for the data buffer tags. FreeBSD/sparc64 is
more strict about checking these values that other arches.

Sync perforce IDs for changes first committed to FreeBSD and then
to the Adaptec driver repository.

The ahc driver should only have one devclass, not one for each bus
attachment.

Submitted by: too many people to count
MFC after: 3 days

Sync perforce Ids.

Allow the ahc and ahd drivers to be built as modules. This also
breaks the ahc driver into a core back-end and pci and eisa
front-ends.

Major update to the aic7xxx driver:

ahc_eisa.c:
ahc_pci.c:
Conform to new aic7xxx IRQ API.

Adapt to aic7xxx_freebsd -> aic7xxx_osm changes.

aic7770.c:
Disable card generated interrupt early in our probe for
"extra safety"

Commonize some seeprom code with the PCI side of the driver.

aic7xxx.c:
Correctly initialize a few scratch ram locations during
a sequencer restart. This avoids spurious sequencer ram
parity errors in some configurations.

Include the softc in ahc_update_residual calls. We need it
for some diagnostics in this code path.

Flag a data overrun on an auto-request sense failure as a
CAM_AUTOSENSE_FAIL rather than a CAM_DATA_RUN_ERR.

Force a renegotiation after noticing a parity error. This
covers targets that lose our negotiation settings but don't
bother to give us a unit attention condition. This can happen
if a target fails during a reselection of us during a cable
pull.

Convert some code to using constants.

Fix some typos.

Correct target mode message loop handling. ahc_clear_msg_state
was not clearing the "need to go to message out phase" bit once
our loop was over.

Simplify some abort handling code.

Include tag information in target mode immediate notify events.

When shutting down EISA controllers, don't EISA BIOS settings in
the high portions of scratch ram. This fixes warm boot issues on
some systems.

Save a bit of space by only allocating the SCBs that we can use.

Avoid some code paths in ahc_abort_scbs() if we are currently
acting as a target.

Correctly cleanup stranded SCBs in the card's SCB array. These
are SCBs who's mapping has already been torn down by code that
aborted the SCB by seeing it in another list first.

Add a comment about some potential bus reset issues for target
mode on Twin (EISA only) controllers.

aic7xxx.h:
Cleanup the hardware scb definitions a bit.

Allocate a ful 256 byte scb mapping index. This simplifies
the lookup code since the table covers all possible (and potentially
bogus) values.

Make AHC_DEBUG work again.

aic7xxx.reg:
Updates to hardware SCB definition.

New definitions for target mode fixes.

aic7xxx.seq:
In target mode, initialize SAVED_LUN just after we receive
the identify message. It may be required in the error recovery
path when a normal cdb packet (includes lun) is not sent up to
the host for processing.

Respond to irregular messages during a selection in target mode.

Defer looking for space for a cdb packet until we are about to
enter command phase. We want to be able to handle irregular messages
even if we would otherwise return QUEUE_FULL or BUSY.

Add support for sending Ignore Wide Residue messages as a target.

In the disable disconnect case in target mode, set our transfer
rate correctly once data are availble.

aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
Add the ability to write and erase the seeprom.

aic7xxx_inline.h:
Correct Big Endian handling of large cdb sizes (> 12 bytes).

Adaptec to changes in the calc_residual API.

Correct a target mode bug where we always attempted to service
the input queue even if no progress could be made due to lack
of ATIOs.

aic7xxx_osm.c:
Adaptec to new IRQ mapping API. The new API allows the core
to only enable our IRQ mapping once it is safe (sufficient
initialization) to do so.

Slap bootverbose protection around some diagnostics.

Only attempt DT phases if we are wide.

aic7xxx_osm.h:
Enable big endian support.

Adjust for IRQ API change.

aic7xxx_pci.c:
Be more careful about relying on subvendor 9005 information.
We now only trust it for HBAs. This should allow the driver
to attach to some MBs where the subvendor/device information
does not follow the Adaptec spec.

Only enable interrupts on the card once we are fully setup.

Disable external SCB ram usage on the aic7895. I have not
been able to make it 100% reliable.

Adjust to seeprom routines being properly prefixed with "ahc".

Fix a few bugs in the external SCB ram probing routine. We
need to clear any parity errors we've triggered during the
probe to avoid future, fatal, interrupts.

If we detect an invalid cable combination, pretent there are
no cable at all. This will enable all of the terminators
which is probably the safest configuration we can "guess".

MFC after: 4 days

ahc_eisa.c:
ahc_pci.c:
Prepare for making ahc a module by adding module dependency
and version info.

aic7770.c:
Remove linux header ifdefs. The headers are handled differently
in Linux where local includes (those using "'s instead of <>'s)
are allowed.

Don't map our interrupt until after we are fully setup to
handle interrupts. Our interrupt line may be shared so
an interrupt could occur at any time.

aic7xxx.c:
Remove linux header ifdefs.

current->curr to avoid Linux's use of current as a
#define for the current task on some architectures.

Add a helper function, ahc_assert_atn(), for use in
message phases we handle manually. This hides the fact
that U160 chips with the expected phase matching disabled
need to have SCSISIGO updated differently.

if (ahc_check_residual(scb) != 0)
ahc_calc_residual(scb);
else
ahc_set_residual(scb, 0);

becomes:

ahc_update_residual(scb);

Modify scsi parity error (or CRC error) handling to
reflect expected phase being disabled on U160 chips.

Move SELTO handling above BUSFREE handling so we can
use the new busfree interrupt behavior on U160 chips.

In ahc_build_transfer_msg() filter the period and ppr_options
prior to deciding whether a PPR message is required.
ppr_options may be forced to zero which will effect our
decision.

Correct a long standing but latent bug in ahc_find_syncrate().
We could choose a DT only rate even though DT transfers were
disabled. In the CAM environment this was unlikely as CAM
filters our rate to a non-DT value if the device does not
support such rates.

When displaing controller characteristics, include the
speed of the chip. This way we can modify the transfer
speed based on optional features that are enabled/disabled
in a particular application.

Add support for switching from fully blown tagged queing
to just using simple queue tags should the device reject
an ordered tag.

Remove per-target "current" disconnect and tag queuing
enable flags. These should be per-device and are not
referenced internally be the driver, so we let the OSM
track this state if it needs to.

Use SCSI-3 message terminology.

aic7xxx.h:
The real 7850 does not support Ultra modes, but there are
several cards that use the generic 7850 PCI ID even though
they are using an Ultra capable chip (7859/7860). We start
out with the AHC_ULTRA feature set and then check the
DEVSTATUS register to determine if the capability is really
present.

current -> curr

ahc_calc_residual() is no longer static allowing it to
be called from ahc_update_residual() in aic7xxx_inline.h.

Update some serial eeprom definitions for the latest
BIOS versions.

aic7xxx.reg:
Add a combined DATA_PHASE mask to the SCSIPHASE register
definition to simplify some sequencer code.

aic7xxx.seq:
Take advantage of some performance features available only
on the U160 chips. The auto-ack feature allows us to ack
data-in phases up to the data-fifo size while the sequencer
is still setting up the DMA engine. This greatly reduces
read transfer latency and simplifies testing for transfer
complete (check SCSIEN only). We also disable the expected
phase feature, and enable the new bus free interrupt behavior,
to avoid a few instructions.

Re-arrange the Ultra2+ data phase handling to allow us to
do more work in parallel with the data fifo flushing on a
read.

On an SDTR, ack the message immediately so the target can
prepare the next phase or message byte in parallel with
our work to honor the message.

aic7xxx_93cx6.c:
Remove linux header ifdefs.

aic7xxx_freebsd.c:
current -> curr

Add a module event handler.

Handle tag downgrades in our ahc_send_async() handler.
We won't be able to downgrade to "basic queuing" until
CAM is made aware of this queuing type.

aic7xxx_freebsd.h:
Include cleanups.

Define offsetof if required.

Correct a few comments.

Update prototype of ahc_send_async().

aic7xxx_inline.h:
Implement ahc_update_residual().

aic7xxx_pci.c:
Remove linux header ifdefs.

Correct a few product strings.

Enable several U160 performance enhancing features.

Modify Ultra capability determination so we will enable
Ultra speeds on devices with a 7850 PCI id that happen
to really be a 7859 or 7860.

Don't map our interrupt until after we are fully setup to
handle interrupts. Our interrupt line may be shared so
an interrupt could occur at any time.

This is an MFC candidate.

ahc_eisa.c:
Change aic7770_map_int to take an additional irq parameter.
Although we can get the irq from the eisa dev under FreeBSD,
we can't do this under linux, so the OSM interface must supply
this.

ahc_pci.c:
Move ahc_power_state_change() to the OSM. This allows us to
use a platform supplied function that does the same thing.
-current will move to the FreeBSD native API in the near
future.

aic7770.c:
Sync up with core changes to support Linux EISA.

We now store a 2 bit primary channel number rather
than a bit flag that only allows b to be the primary
channel. Adjust for this change.

aic7xxx.c:
Namespace and staticization cleanup. All exported symbols
use an "ahc_" prefix to avoid collisions with other modules.

Correct a logic bug that prevented us from dropping
ATN during some exceptional conditions during message
processing.

Take advantage of a new flag managed by the sequencer
that indicates if an SCB fetch is in progress. If so,
the currently selected SCB needs to be returned to the
free list to prevent an SCB leak. This leak is a rarity
and would only occur if a bus reset or timeout resulting
in a bus reset occurred in the middle of an SCB fetch.

Don't attempt to perform ULTRA transfers on ultra capable
adapters missing the external precision resistor required
for ultra speeds. I've never encountered an adapter
configured this way, but better safe than sorry.

Handle the case of 5MHz user sync rate set as "0" instead of 0x1c
in scratch ram.

If we lookup a period of 0 in our table (async), clear the scsi offset.

aic7xxx.h:
Adjust for the primary channel being represented as
a 2 bit integer in the flags member of the ahc softc.

Cleanup the flags definitions so that comment blocks are
not cramped.

Update seeprom definitions to correctly reflect the fact
that the primary channel is represented as a 2 bit integer.

Add AHC_ULTRA_DIASABLED softc flag to denote controllers
missing the external precision resistor.

aic7xxx.reg:
Add DFCACHETH to the definition of DFSTATUS for completness sake.

Add SEQ_FLAGS2 which currently only contains the SCB_DMA
(SCB DMA in progress) flag.

aic7xxx.seq:
Correct a problem when one lun has a disconnected untagged
transaction and another lun has disconnected tagged transactions.
Just because an entry is found in the untagged table doesn't
mean that it will match. If the match on the lun fails, cleanup
the SCB (return it to the disconnected list or free it), and snoop
for a tag message. Before this change, we reported an unsolicited
reselection. This bug was introduced about a month ago during an
overly aggressive optimization pass on the reselection code.

When cleaning up an SCB, we can't just blindly free the SCB. In
the paging case, if the SCB came off of the disconnected list, its
state may never have been updated in host memory. So, check the
disconnected bit in SCB_CONTROL and return the SCB to the disconnected
list if appropriate.

Manage the SCB_DMA flag of SEQ_FLAGS2.

More carefully shutdown the S/G dma engine in all cases by using
a subroutine. Supposedly not doing this can cause an arbiter hang
on some ULTRA2 chips.

Formatting cleanup.

On some chips, at least the aic7856, the transition from
MREQPEND to HDONE can take a full 4 clock cycles. Test
HDONE one more time to avoid this race. We only want our
FIFO hung recovery code to execute when the engine is
really hung.

aic7xxx_93cx6.c:
Sync perforce ids.

aic7xxx_freebsd.c:
Adjust for the primary channel being a 2 bit integer
rather than a flag for 'B' channel being the primary.

Namespace cleanup.

Unpause the sequencer in one error recovery path that
neglected to do so. This could have caused us to perform
a bus reset when a recovery message might have otherwise been
successful.

aic7xxx_freebsd.h:
Use AHC_PCI_CONFIG for controlling compilation of PCI
support consistently throughout the driver.

Move ahc_power_state_change() to OSM.

aic7xxx_inline.h
Namespace cleanup.

Adjust our interrupt handler so it will work in the edge
interrupt case. We must process all interrupt sources
when the interrupt fires or risk not ever getting an
interrupt again. This involves marking the fact
that we are relying on an edge interrupt in ahc->flags
and checking for this condition in addition to the
AHC_ALL_INTERRUPTS flag. This fixes hangs on the
284X and any other aic7770 installation where level
interrupts are not available.

aic7xxx_pci.c:
Move the powerstate manipulation code into the OSM. Several
OSes now provide this functionality natively.

Take another shot at using the data stored in scratch ram
if the SCB2 signature is correct and no SEEPROM data is
available. In the past this failed if external SCB ram
was configured because the memory port was locked. We
now release the memory port prior to testing the values
in SCB2 and re-acquire it prior to doing termination control.

Adjust for new 2 bit primary channel setting.

Trust the STPWLEVEL setting on v 3.X BIOSes too.

Configure any 785X ID in the same fashion and assume
that any device with a rev id of 1 or higher has the
PCI 2.1 retry bug.

Update Copyright notices for new year. (should have been in last commit).

ahc_eisa.c:
Initialize rid to 0. This doesn't seem to make any difference
(the driver doesn't care what rid it gets and no-one seems to
check rid's value), but follows standard conventions.

Pass in our device_t to ahc_alloc(). We now use device_T
softc storage, so passing NULL results in a panic.

Set the unit number in our softc so that the driver core
can retrieve it.

ahc_pci.c:
Set the unit number in our softc so that the driver core
can retrieve it.

aic7770.c:
Insert our softc into the list of softcs when initialization
is successful.

aic7xxx.c:
Remove a workaround for an aic7895 bug we will never trigger.

Add additional diagnostic info to ahc_dump_card_state().

Always panic the system if a sequencer assertion fails.

AHC_SCB_BTT is a "flag" not a "feature". Check the right
field in the softc.

Replace a hard coded number with a constant.

Guard against looping forever in ahc_pause_and_flushwork().
A hot eject or card failure may make the intstat register
return 0xFF, so limit the number of interrupts we'll process.

Correct the code in ahc_search_qinfifo() that guarantees that
the sequencer will see an abort collision if the qinfifo is
modified when a DMA is in progress. We now do this fixup
after modifying the queue. This guarantees that the HSCB
we place at the head of the queue is not the same as the
old head. Using "next hscb" (guaranteed not to be the
same as the first SCB) before clearing the queue could free
up the original head hscb to be used during a remove operation
placing it again at the head of the qinfifo.

aic7xxx.h:
Reduce the maximum number of outstanding commands to 253 from
254. To handle our output queue correctly on machines that only
support 32bit stores, we must clear the array 4 bytes at a
time. To avoid colliding with a DMA write from the sequencer,
we must be sure that 4 slots are empty when we write to clear
the queue. This reduces us to 253 SCBs: 1 that just completed
and the known three additional empty slots in the queue that
preceed it. Yahoo was able to force this race on one of their
systems. Interrupts were disabled for such a time that the
entire output queue was filled (254 entries complete without
any processing), and our 32bit write to clear the status clobbered
one entry.

Add a feature tag for devices that are removable.

aic7xxx.reg:
Never use the sequencer interrupt value of 0xF0. We need
to guanrantee that an INTSTAT value of 0xFF can only occur
during card failure or a hot-eject.

Align the busy targets table with the begining of scratch
space. This seems to appease a chip bug in the aic7895.

aic7xxx.seq:
Be sure to disable select-out after a bus free event that occurs
early in a selection. If we don't disable select-out, we will
believe that it is enabled even though a new selection will never
occur.

Move the clearing of SELDI to just before a jump. This appeases
another chip bug of the aic7895.

Make the target mode command loop a bit more efficient.

AHC_SCB_BTT is a "flag" not a "feature". Check the right
field in the softc.

Properly cleanup the last SCB we tested against should we
fail to properly find an SCB for a reselection.

Add some additional sequencer debugging code.

aic7xxx_freebsd.c:
Limit the driver to 253 outstanding commands per adapter.

Guard against overflow in timeout handling.

aic7xxx_inline.h:
AHC_SCB_BTT is a "flag" not a "feature". Check the right
field in the softc.

aic7xxx_pci.c:
Set the removable feature for the apa1480 cardbus and the 29160C
Compact PCI card.

Don't report high byte termination information for narrow cards.

Use a PCI read rather than a questionable delay when fetching/setting
termination settings.

ahc_eisa.c:
ahc_pci.c:
Add detach support.

Make use of soft allocated on our behalf by newbus.

For PCI devices, disable the mapping type we aren't
using for extra protection from rogue code.

aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
Sync perforce IDs.

aic7xxx_freebsd.c:
Capture the eventhandle returned by EVENTHANDER_REGISTER
so we can kill the handler off during detach.

Use AHC_* constants instead of hard coded numbers in a
few more places.

Test PPR option state when deciding to "really" negotiate
when the CAM_NEGOTIATE flag is passed in a CCB.

Make use of core "ahc_pause_and_flushwork" routine in our
timeout handler rather than re-inventing this code.

Cleanup all of our resources (really!) in ahc_platform_free().
We should be all set to become a module now.

Implement the core ahc_detach() routine shared by all of
the FreeBSD front-ends.

aic7xxx_freebsd.h:
Softc storage for our event handler.

Null implementation for the ahc_platform_flushwork() OSM
callback. FreeBSD doesn't need this as XPT callbacks are
safe from all contexts and are done directly in ahc_done().

aic7xxx_inline.h:
Implement new lazy interrupt scheme. To avoid an extra
PCI bus read, we first check our completion queues to
see if any work has completed. If work is available, we
assume that this is the source of the interrupt and skip
reading INTSTAT. Any remaining interrupt status will be
cleared by a second call to the interrupt handler should
the interrupt line still be asserted. This drops the
interrupt handler down to a single PCI bus read in the
common case of I/O completion. This is the same overhead
as in the not so distant past, but the extra sanity of
perforning a PCI read after clearing the command complete
interrupt and before running the completion queue to avoid
missing command complete interrupts added a cycle.

aic7xxx.c:
During initialization, be sure to initialize all scratch
ram locations before they are read to avoid parity errors.
In this case, we use a new function, ahc_unbusy_tcl() to
initialize the scratch ram busy target table.

Replace instances of ahc_index_busy_tcl() used to unbusy
a tcl without looking at the old value with ahc_unbusy_tcl().

Modify ahc_sent_msg so that it can find single byte messages.
ahc_sent_msg is now used to determine if a transfer negotiation
attempt resulted in a bus free.

Be more careful in filtering out only the SCSI interrupts
of interest in ahc_handle_scsiint.

Rearrange interrupt clearing code to ensure that at least
one PCI transaction occurrs after hitting CLRSINT1 and
writting to CLRINT. CLRSINT1 writes take a bit to
take effect, and the re-arrangement provides sufficient
delay to ensure the write to CLRINT is effective. The
old code might report a spurious interrupt on some "fast"
chipsets.

export ahc-update_target_msg_request for use by OSM code.

If a target does not respond to our ATN request, clear
it once we move to a non-message phase. This avoids
sending a MSG_NOOP in some later message out phase.

Use max lun and max target constants instead of
hard-coded values.

Use softc storage built into our device_t under FreeBSD.

Fix a bug in ahc_free() that caused us to delete
resources that were not allocated.

Clean up any tstate/lstate info in ahc_free().

Clear the powerdown state in ahc_reset() so that
registers can be accessed.

Add a preliminary function for pausing the chip and
processing any posted work.

Add a preliminary suspend and resume functions.

aic7xxx.h:
Limit the number of supported luns to 64. We don't
support information unit transfers, so this is the
maximum that makes sense for these chips.

Add a new flag AHC_ALL_INTERRUPTS that forces the
processing of all interrupt state in a single invokation
of ahc_intr(). When the flag is not set, we use the
lazy interrupt handling scheme.

Add data structures to store controller state while
we are suspended.

Use constants instead of hard coded values where appropriate.

Correct some harmless "unsigned/signed" conflicts.

aic7xxx.seq:
Only perform the SCSIBUSL fix on ULTRA2 or newer controllers.
Older controllers seem to be confused by this.

In target mode, ignore PHASEMIS during data phases.
This bit seems to be flakey on U160 controllers acting
in target mode.

aic7xxx_pci.c:
Add support for the 29160C CPCI adapter.

Add definitions for subvendor ID information
available for devices with the "9005" vendor id.
We currently use this information to determine
if a multi-function device doesn't have the second
channel hooked up on a board.

Add rudimentary power mode code so we can put the
controller into the D0 state. In the future this
will be an OSM callback so that in FreeBSD we don't
duplicate functionality provided by the PCI code.
The powerstate code was added after I'd completed
my regression tests on this code.

Only capture "left over BIOS state" if the POWRDN
setting is not set in HCNTRL.

In target mode, don't bother sending incremental
CRC data.

Move aicasm to its own subdirectory.

Separate our platform independent hooks from core driver functionality
shared between platforms (FreeBSD and Linux at this time).

Add sequencer workarounds for several chip->chipset interactions.

Correct external SCB corruption problem on aic7895 based cards (3940AUW).

Lots of cleanups resulting from the port to another OS.

o Convert to <inttypes.h> style fixed sized types to facilitate porting to
other systems.

o Normalize copyright text.

o Clean up probe code function interfaces by passing around a single
structure of common arguments instead of passing "too many" args
in each function call.

o Add support for the AAA-131 as a SCSI adapter.

o Add support for the AHA-4944 courtesy of "Matthew N. Dodd" <winter@jurai.net

o Correct manual termination support for PCI cards. The bit definitions
for manual termination control in the SEEPROM were incorrect.

o Add support for extracting NVRAM information from SCB 2 for BIOSen
that use this mechanism to pass this data to OS drivers.

o Properly set the STPWLEVEL bit in PCI config space based on the
setting in an SEEPROM.

o Go back to useing 32byte SCBs for all controllers. The current
firmware allows us to embed 12byte cdbs on all controllers in
a 32byte SCB, and larger cdbs are rarely used, so it is a
better use of this space to offer more SCBs (32).

o Add support for U160 transfers.

o Add an idle loop executed during data transfers that prefetches
S/G segments on controllers that have a secondary DMA engine
(aic789X).

o Improve the performance of reselections by avoiding an extra
one byte DMA in the case of an SCB lookup miss for the reselecting
target. We now keep a 16byte "untagged target" array on the card
for dealing with untagged reselections. If the controller has
external SCB ram and can support 64byte SCBs, then we use an
"untagged target/lun" array to maximize concurrency. Without
external SCB ram, the controller is limited to one untagged
transaction per target, auto-request sense operations excluded.

o Correct the setup of the STPWEN bit in SXFRCTL1. This control
line is tri-stated until set to one, so set it to one and then
set it to the desired value.

o Add tagged queuing support to our target role implementation.

o Handle the common cases of the ignore wide residue message
in firmware.

o Add preliminary support for 39bit addressing.

o Add support for assembling on big-endian machines. Big-endian
support is not complete in the driver.

o Correctly remove SCBs in the waiting for selection queue when
freezing a device queue.

o Now that we understand more about the autoflush bug on the
aic7890, only use the workaround on devices that need it.

o Add a workaround for the "aic7890 hangs the system when you
attempt to pause it" problem. We can now pause the aic7890
safely regardless of what instruction it is executing.

remove #include "eisa.h" and #if NEISA > 0 - this is guaranteed by
config since ahc_eisa.c is "optional ahc eisa" meaning "only compile
ahc_eisa if ahc and eisa are defined"

Pre 4.0 tidy up.

Collect together the components of several drivers and export eisa from
the i386-only area (It's not, it's on some alphas too). The code hasn't
been updated to work on the Alpha yet, but that can come later.

Repository copies were done a while ago.
Moving these now keeps them in consistant place across the 4.x series
as the newbusification progresses.

Submitted by: mdodd

$Id$ -> $FreeBSD$

Properly set the alignment argument to bus_dma_tag_create(). If we
don't care about the alignment, set it to 1, meaning single byte alignment.

Move the specification of EDGE/LEVEL triggered interrupts to
eisa_add_intr() which now takes an additional arguement (one of
EISA_TRIGGER_LEVEL or EISA_TRIGGER_EDGE).

The flag RR_SHAREABLE has no effect when passed to
bus_alloc_resource(dev, SYS_RES_IRQ, ...) in an EISA device context as
the eisa_alloc_resource() call (bus_alloc_resource method) now deals
with this flag directly, depending on the device ivars.

This change does nothing more than move all the 'shared = inb(foo + iobsse)'
nonesense to the device probe methods rather than the device attach.

Also, print out 'edge' or 'level' in the IRQ announcement message.

Reviewed by: dfr

Correct the comment for the last commit.

Clean up the handling of failure modes in our attach so we don't free
resources twice. ahc_free() will do all of the work for us (as would
be required by an unload event) so we only need to handle resources that
the softc has not taken ownership of.

Fix whitespace. Correct a comment.

Move the declaration of the interrupt type from the driver structure
to the BUS_SETUP_INTR call.

ahb.c:
Synchronize malloc types for our softc.

ahc_eisa.c:
Sync to aic7xxx driver bus dma and new bus changes.

Implement an EISA new-bus framework. The old driver probe mechanism
had a quirk that made a shim rather hard to implement properly and it was
just easier to convert the drivers in one go. The changes to the
buslogic driver go beyond just this - the whole driver was new-bus'ed
including pci and isa. I have only tested the EISA part of this so far.

Submitted by: Doug Rabson <dfr@nlsystems.com>

Modify to deal with changes in the storage of user negotiation settings.

Pull in new ccb_hdr list types.

Bring back support for honoring the primary channel setting for twin channel
EISA adapters. This could have caused the system to find the wrong root
disk.

Reviewed by: J Wunsch <j@ida.interface-business.de>

Pass termination information via softc flags to the core driver. The
EISA probe missed out on this change in attach->core API.

Move to new name and convert to CAM.