MFC r344360,r344361: zpool.8: document -D flag for zpool status

Also, sort zpool status flags in the same order as in illumos manual.

MFC r337007: MFV r336991, r337001:
9102 zfs should be able to initialize storage devices

The first access to a disk block can incur a performance penalty on some
platforms (e.g. AWS's EBS, VMware VMDKs). Therefore it is recommended that
volumes be "thick provisioned", where supported by the platform (VMware).
Thick provisioning is time consuming and often is ignored. If the thick
provision step is omitted, customers will see suboptimal performance until
we have written to all parts of the LUN. ZFS should be able to initialize
any unused storage to remove any first-write penalty that exists.

illumos/illumos-gate@094e47e980b0796b94b1b8f51f462a64d246e516

Reviewed by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
Author: George Wilson <george.wilson@delphix.com>

MFC r333081 (by eadler):
zpool(8): correct list of default properties in 'list'.

The default provides output in the following form:
```
NAME SIZE ALLOC FREE CKPOINT EXPANDSZ FRAG CAP DEDUP
HEALTH ALTROOT
```

this corrects the man page.

Also submitted upstream as
https://github.com/openzfs/openzfs/pull/632/files (with slightly
different changes needed)

MFC r332426: allow ZFS pool to have temporary name for duration of current import

The change adds -t <name> option to zpool create and -t option to zpool
import in its form with an old name and a new name. This allows to
import (or create) a pool under a name that's different from its real,
permanent name without affecting that name. This is useful when working
with VM images or images of other physical systems if they happen to
have a ZFS pool with the same name as the host system.

Sponsored by: Panzura (porting)

MFC r332641: MFV man pages update from r329502:
7614 zfs device evacuation/removal.

MFC r331701: MFV r331695, 331700: 9166 zfs storage pool checkpoint

illumos/illumos-gate@8671400134a11c848244896ca51a7db4d0f69da4

The idea of Storage Pool Checkpoint (aka zpool checkpoint) deals with
exactly that. It can be thought of as a “pool-wide snapshot” (or a
variation of extreme rewind that doesn’t corrupt your data). It remembers
the entire state of the pool at the point that it was taken and the user
can revert back to it later or discard it. Its generic use case is an
administrator that is about to perform a set of destructive actions to ZFS
as part of a critical procedure. She takes a checkpoint of the pool before
performing the actions, then rewinds back to it if one of them fails or puts
the pool into an unexpected state. Otherwise, she discards it. With the
assumption that no one else is making modifications to ZFS, she basically
wraps all these actions into a “high-level transaction”.

Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
Author: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>

MFC r323355: MFV r323107: 8414 Implemented zpool scrub pause/resume

illumos/illumos-gate@1702cce751c5cb7ead878d0205a6c90b027e3de8
https://github.com/illumos/illumos-gate/commit/1702cce751c5cb7ead878d0205a6c90b027e3de8

FreeBSD note: rather than merging the zpool.8 update I copied the zpool
scrub section from the illumos zpool.1m to FreeBSD zpool.8 almost
verbatim. Now that the illumos page uses the mdoc format, it was an
easier option. Perhaps the change is not in perfect compliance with the
FreeBSD style, but I think that it is acceptible.

https://www.illumos.org/issues/8414
This issue tracks the port of scrub pause from ZoL: https://github.com/zfsonlinux/zfs/pull/6167
Currently, there is no way to pause a scrub. Pausing may be useful when
the pool is busy with other I/O to preserve bandwidth.

Description

This patch adds the ability to pause and resume scrubbing. This is achieved
by maintaining a persistent on-disk scrub state. While the state is 'paused'
we do not scrub any more blocks. We do however perform regular scan
housekeeping such as freeing async destroyed and deadlist blocks while paused.

Motivation and Context

Scrub pausing can be an I/O intensive operation and people have been asking
for the ability to pause a scrub for a while. This allows one to preserve scrub
progress while freeing up bandwidth for other I/O.

Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Author: Alek Pinchuk <apinchuk@datto.com>

MFC r302787

zpool(8): update Hot Spares section to mention zfsd(8)

Approved by: re (gjb)