- Copy stable/10@296371 to releng/10.3 in preparation for 10.3-RC1
builds.
- Update newvers.sh to reflect RC1.
- Update __FreeBSD_version to reflect 10.3.
- Update default pkg(8) configuration to use the quarterly branch.

Approved by: re (implicit)

MFC r260607, r260610, r260934:

r260607:
The onyx codec works also as module, so add it.

r260610:
Described in the man page but not implemented. Here it comes,
atomic_swap_32/64. The latter only for powerpc64.

r260934:
Fix the resource information for the i2s-a node on certain G5 PowerMacs.
This is the first step needed to get the snapper codec working on those
machines.
The second step is to enable the corresponding I2S device and its clock.

Tested on machines where the snapper codec was already working, a G4 PowerBook
and a PowerMac9,1 with a Shasta based macio.
The PowerMac7,2/7,3 with a K2 based macio can now also play sound.

Copy head (r256279) to stable/10 as part of the 10.0-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Add the macio attachment for wi(4). Partially obtained from NetBSD.

Reviewed by: adrian
Obtained from: NetBSD (partially)

Do not use Open Firmware to open the device and instead program its start
on our own. This prevents hangs at boot when using a bm(4) NIC where the
cable is not plugged in at boot time.

Obtained from: NetBSD
MFC after: 1 week

Take into account the size of the interrupt cell. It's determined
by the parent for interrupt resources. This corrects parsing of
the interrupts property.

With parsing of the property fixed, add all interrupts to the
resource list. Bump the max. number of interrupts from 5 to 6
as scc(4) attached to macio(4) has 6 interrupts (3 per channel).

Submitted by: Nathan Whitehorn <nathanw@uchicago.edu>

Convert to use the recently introduced set of ofw_bus_gen_get_*() for
providing the ofw_bus KOBJ interface.

Tested by: grehan

/* -> /*- for license, minor formatting changes

- Introduce an ofw_bus kobj-interface for retrieving the OFW node and a
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.

Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386

Move soft structs back to C files to avoid exposing rman fields
to clients now that it's protected with __RMAN_RESOURCE_VISIBLE

Rework of how memory resources are discovered and dealt with in macio.
- Store the OpenFirmware "reg" property in the macio ivars.
- Use a struct to define the structure of a "reg" property entry.
- Discover all memory ranges, not just the first.
- In ata_macio, manage our own range and hand out our own allocations using
bus_space_subregion.
- Fix bus_space_subregion to handle subregions of sparse maps.

- Remove the ignore list and replace it with a quirk list of sorts.
- Add a quirk type for devices whose interrupt properties are actually
attached to their children.
- Flag the "escc" (zs-alike serial controller) device as having this quirk.
- Rework the interrupt discovery code to deal with devices that have more than
one interrupt.

Driver for the macio south bridge, and ATA cell contained within.

Approved by: benno