- Copy stable/10@296371 to releng/10.3 in preparation for 10.3-RC1
builds.
- Update newvers.sh to reflect RC1.
- Update __FreeBSD_version to reflect 10.3.
- Update default pkg(8) configuration to use the quarterly branch.

Approved by: re (implicit)

MFC r272719:

cxgbe/tom: don't leak resources tied to an active open request that
cannot be sent to the chip because a prerequisite L2 resolution
failed.

Copy head (r256279) to stable/10 as part of the 10.0-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

- Make note of interface MTU change if the rx queues exist, and not just
when the interface is up.
- Add a tunable to control the TOE's rx coalesce feature (enabled by
default as it always has been). Consider the interface MTU or the
coalesce size when deciding which cluster zone to use to fill the
offload rx queue's free list. The tunable is:
dev.{t4nex,t5nex}.<N>.toe.rx_coalesce

MFC after: 1 day

The T5 allows the driver to specify the ISS. Do so; use the ISS picked
by the kernel.

MFC after: 1 day

- Read all TP parameters in one place.
- Read the filter mode, calculate various shifts, and use them
properly during active open (in select_ntuple).

MFC after: 1 day

cxgbe/tom: Slight simplification of code that calculates options2.

MFC after: 3 days

cxgbe(4): Add support for Chelsio's Terminator 5 (aka T5) ASIC. This
includes support for the NIC and TOE features of the 40G, 10G, and
1G/100M cards based on the T5.

The ASIC is mostly backward compatible with the Terminator 4 so cxgbe(4)
has been updated instead of writing a brand new driver. T5 cards will
show up as cxl (short for cxlgb) ports attached to the t5nex bus driver.

Sponsored by: Chelsio

Add a couple of missing error codes. Treat CPL_ERR_KEEPALV_NEG_ADVICE as
negative advice and not a fatal error.

MFC after: 3 days

cxgbe/tom: Add support for fully offloaded TCP/IPv6 connections (active open).

MFC after: 1 week

Minor cleanup: use bitwise ops instead of pointless wrappers around
setbit/clrbit.

Correctly handle the case where an inp has already been dropped by the time
the TOE driver reports that an active open failed. toe_connect_failed is
supposed to handle this but it should be provided the inpcb instead of the
tcpcb which may no longer be around.

Support for TCP DDP (Direct Data Placement) in the T4 TOE module.

Basically, this is automatic rx zero copy when feasible. TCP payload is
DMA'd directly into the userspace buffer described by the uio submitted
in soreceive by an application.

- Works with sockets that are being handled by the TCP offload engine
of a T4 chip (you need t4_tom.ko module loaded after cxgbe, and an
"ifconfig +toe" on the cxgbe interface).
- Does not require any modification to the application.
- Not enabled by default. Use hw.t4nex.<X>.toe.ddp="1" to enable it.

- Updated TOE support in the kernel.

- Stateful TCP offload drivers for Terminator 3 and 4 (T3 and T4) ASICs.
These are available as t3_tom and t4_tom modules that augment cxgb(4)
and cxgbe(4) respectively. The cxgb/cxgbe drivers continue to work as
usual with or without these extra features.

- iWARP driver for Terminator 3 ASIC (kernel verbs). T4 iWARP in the
works and will follow soon.

Build-tested with make universe.

30s overview
============
What interfaces support TCP offload? Look for TOE4 and/or TOE6 in the
capabilities of an interface:
# ifconfig -m | grep TOE

Enable/disable TCP offload on an interface (just like any other ifnet
capability):
# ifconfig cxgbe0 toe
# ifconfig cxgbe0 -toe

Which connections are offloaded? Look for toe4 and/or toe6 in the
output of netstat and sockstat:
# netstat -np tcp | grep toe
# sockstat -46c | grep toe

Reviewed by: bz, gnn
Sponsored by: Chelsio communications.
MFC after: ~3 months (after 9.1, and after ensuring MFC is feasible)